Directorate Of Municipal Administration Tender

KSRB 4.9.2 : Providing T.M.T steel reinforcement for R.C.C work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of machinery complete as per specifications. Specification No. KBS 4.6.3 - TMT bars Fe 500

KSRB 7.9 : Providing and fixing M.S.grill work for windows and ventilators weighing 21kg/sqm using M.S. flats, or M.S. square rods, or combination of M.S. flats and square rods as per approved design, drawing including cutting steel sections and welding the same to required pattern with a coat of red lead primer, cost of materials, fixtures, labour and HOM of machinery complete as per specifications. Specification No. KBS 7.12

Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 3.5 core 25 sqmm

Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required.In existing trench/duct.25 sqmm to 75 sqmm

Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1 KV.

Supplying and fixing L.T. cast Iron pot heads suitable for 1.1 KV class UG cable filled with necessary bitumen/insulating compound complete with terminals, clamps, bolts, nuts and washers etc.

Supplying and fixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only

Supplying Bitumen Compound and covering the cable joint/ pot heads

Supplying and drawing 3 core flat PVC sheathed submersible pump cable manufactured with electrolytic grade copper with flexible copper with low resistance conductor confirming to IS:8130-1984 and virgin grade PVC insulation and powder coating extruded PVC sheathed suitable for working voltage upto 1100Volts as per IS-694:1990. 3C X 6.0Sq.mm

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 25 sqmm Long Barrel

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. 4 sqmm

Wiring for lighting/power circuit using one of PVC insulated 1100V grade, stranded Aluminium wire single core in open or concealed system of wiring.10 sqmm

Fabricating supplying and mounting MS box made out … SWG suitable for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete. 14SWG

Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. flat … with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. 50x50x6mm

Supplying ......... amps rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete 100Amps 4x30x6mm Aluminium Strips

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of Overload and Short circuit with thermal Magnetic/Micro processor release and Earth Fault as per IS-13947. ( Icu = Ics) 125 Amps 25kA. 4 pole

Supplying of on load change over switches 4 poles, AC-23A Duty, 415V, 50Hz, AC Supply. With all accessories. (SM Enclosure Sheet Metal Execution)100 Amps

Supplying, fixing and wiring Earth Leakage Miniature Circuit Breaker (ELMCB) 240/450V up to 300mA sensitivity on existing wood/panel board. 32-40 Amps 4 pole

Supplying, fixing and wiring rotary selector switch suitable for Ammeter

Supplying, fixing and wiring rotary selector switch suitable for Voltmeter

Supplying, fixing and wiring 3 Phase Digital Ammeter / Voltmete

Supplying, fixing and wiring 50/5 to 400/5Amps 5VA burden Current Transformer. Class 0.5 accuracy with Tape Wound.

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440v A.C. 50 Hz 12/24v D.C.

Supply and fixing of Control Panel Board Indoor type Uniton exsiting panel IS:5124 10- up to 30 HP Electronic Type (star-Delta Panel Board) Including ETico/Btico Equalent, Having NO/NC Contactor, Over Load release, Single Phase preventer with Digital parameter Monitoring. ( Y-V Starter)

supply and fixing of brand new board approved float sensore

Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130-1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS-694:1990 4C X 1.5Sq.mm

Supplying, fixing and wiring Electronic Trivector Meter (ETV) 5 to 32/63 Amps three phase 4 wire whole current class-1 Accuracy Energy Meter.

Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc. using 40mm dia 2.9mm thick 2.5 mtr long GI pipe with GI funnel with mesh and suitable size reducer fixed on the top of the earth electrode. The funnel should be enclosed in a CC chamber of 400x400x400mm with a cast iron cover. The earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 150mm all-round with alternate layers of salt and charcoal from the bottom of the CC chamber. The connection from the electrode is to be established through GI strip using GI bolts and nuts.

Supplying and laying double walled corrugated(DWC) HDPE pipe including all necessary connecting sockets/couplings/Tees/Bends/End-caps of same materials in existing trench as per IS 14930 part-II suitable for drawing under ground cables.50mm OD/38mm ID

Supplying and running of GI/Copper strips for grounding connections, using necessary fixing materials as required.

Supplying,laying,jointing ,testing and commissioning of G.I. Pipes conforming to IS 1239:1990 with latest amendments, including fixing Collars, Elbows, Tees, bends, Glad Cocks and other Fittings (Excluding Cost of Specials) with Cuts and Threads wherever necessary including conveying the materials to workspot, including testing for water tightness with all lead and lifts etc complete (Contractor shall make his own arrangements for procuring water for testing class -c type (heavy duty)100mm dia

supply and fixing of 100mmdia GI coller (heavy duty)

supply and fixing of ductile iron double flanged swing check valve with slanted seat or with lever wieght with straight disc specification as per board approved PN 10 100mm dia

suplly and delivery of resilint saeted soft sealing sluice valves with body ,bonnet of ductile iron of grade ggg50 wedge fully rubber lined with epdm and seal of NBR and the valves shoulb be of vaccume tightand 100% leak proof with face dimention as per BS 5163-89/is 14846-200/din3202 PN 10 100mm dia

PUMPSET: Supply ,delivery and Erection at site brand new any Board approved make non clog submersible sewage pump coupled to squirrel cage induction motor of 10 HP or suitable HP 'F' class insulation capable of delivering 40LPS against 5.00 mtr head. The pump set should operate in full range of discharge and should have the following accessories specified in the following detailed specification. The submersible sewage pump shall be of monoblock type with non-clog design. The pump shall be of max. 1450RPM. The pump should be able to pass through soft solids of 100 mm dia and capable of delivering sludge with specific gravity 0f 1.05 Impellers should be single/double vane non-clog type of CF8M material and with wearing rings. The pump shall be fitted with contra block cutting and tearing system with special grooving system on suction side for disposal of soft solid materials like long fibre, plastics, solid admixes, sludge etc., Maintenance free, antifriction, deep groove permanently grease filled ball bearings to take care of all the axial and radial forces at any point of operations, should be provided.

Supplying of 1.1 KV LT UG cable XLPE or Heat resistantPVC insulated, PVC extruded Inner sheath armoured UG LTcable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouringstrip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-39754 core 10 sqmm

Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation.Lamp compartment comprising of anti glare clear diffuserwith Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66optical and electrical compartment & impact resistance ofcomplete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/Overload, short circuit/ miss-wiring protection. Compatiblefor pole mouting with outer dia of 40mm to 50mmUniversal Voltage driver to operate wide voltage range from100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. ULapproved MCPCB. Top access street light with single screwto ensure ease of maintenance at the sight site locationwith minimized minimal tools. LED Light fixture with ........WSystem Powerconsumption. LED Efficiency>130lm/w,nominal CRI >75. Luminaire manufacturer should have inhousefacility accredited by NABL/CPRI & any Governmentcertified agency & Design & Development facility certifiedby ISO 9001:2008 . Housing with supplier word mark /nameshall be Engraved / Embossing on the die cast housing/ Bodypart. Warranty of 2 Years against any manufacturing defectworking under standard electrical conditions as mentionedabove should be given by LED manufacturer & Cree/Nichia/Lumileds/Osram make LED Source..LED Floodlight 120W