Central Food Technological Research Institute Tender

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In lime mortar

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping groound within 50 metrs lead.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 M sand : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 M sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 M sand), cost of required centering, shuttering complete 1:1½:3 (1 Cement: 1½ M sand: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

15mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement : 4 M Sand)

Structural steel work rivetted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).

Providing & fixing false ceiling tiles below the roof pressed clay tile (Mangalore tile) of 15-20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).

Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately).

Providing and laying vitrified floor tiles in different sizes (minimum thickness 10mm) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 M sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of tile 600X600mm

Providing and laying vitrified tiles in different sizes (minimum 10mm thick), with water absorption less than 0.08% and confirming to IS 15622, of approverd make, in all colours and shade, in skirting, riser of steps, over 12mm thick bed of cment mortar 1:3 (1 cement : 3 M sand) jointing with grey cement slurry @ 3.3kg/Sqm including grouting the joints with white cement and matching pigments etc., complete. Size of tile 600X600mm

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (minimum 5mm thick), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 M sand), jointing with grey cement slurry @ 3.3kg/ sqm including grouting the joints with white cement and matching pigments etc., complete..

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (10mm thickness), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 M sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Size of the tile : 600X300mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiberglass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames. 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Second class teak wood

Providing and fixing fly proof stainless steel grade 304 wire guage, to windows and clerestory windows using wire guage with average width of aperture 1.4mm in bith directions with wire of dia 0.50mm all complete. With 2nd class teak wood beading 62X19 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250X10mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150X10mm

Proiding and fixing antique finished brass aldrops of approved design. 250mm length

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms.

Providing and fixing PTMT urinal cock of approved quality and colour. 15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40mm dia

Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia

Providing and fixing cPVC health faucet of approved design and coulor 15mm nominal dia Make: Hindware - F160188

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15mm nominal bore with 45 cm length

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing CP brass two way bib cock for fixing of health faucet. 15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing CP brass extension nipple (size 15mm X 50mm) of approved make and quality as per the Direction of Engineer-in-charge

Providing and fixing toilet paper holder C.P. brass

Providing and fixing pvc nahani trap of size 100X75mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Oval shape 450x350 mm (outer dimensions)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25mm nominal dia pipes

Providing and fixing cpvc/gun metal gate valve with CI wheel of approved quality (screwed end) 25mm nominal bore

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 M sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 M sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 M sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing, laying and jointing under ground drainage pipe using PVC pipes of 6 kgf/ sq.cm pressure capacity at suitable depth with required slope including testing of joints etc., complete 110 mm diameter Make: Astral, Finolex or Ashirvad

Providing and fixing PVC moulded fittings/accessories for PVC drain pipes including jointing with PVC cement solvent, etc complete. PVC Tee without door - 110mm dia

Providing and fixing PVC moulded fittings/accessories for PVC drain pipes including jointing with PVC cement solvent, etc complete. PVC Bend without door - 110mm dia

Providing and fixing PVC moulded fittings/accessories for PVC drain pipes including jointing with PVC cement solvent, etc complete. PVC Bend with door - 110mm dia

Applying priming coats with primer of approved brand and manufacturer, having low VOC content. With water thinnablecement primer on wall surface having VOC content less than 50gms/litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC content less than 50gms/litre of approved brand and manufacturer, including applying additional coats wherever required to achieve even shade and colour. Two coats

Finishing walls with premium acrylic smooth exterior paint of required shade: New work (Two or more coats applied @ 1.43ltr/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90lts/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Supplying, Installation, Testing & Successful Commissioning of IP65, 20 Watts LED Spot Light (colour, as per choice of Engineer Incharge) complete with internal wiring, 5Amps 2 way PVC Connector, 1 metre length of any standard make rated 3 core copper wire etc.,ready to use and to work with 230V Single Phase, 50Hz AC Supply and suitable to fix on wall / ceiling / wooden or steel rails with required hardwares. Make: Philips / Wipro / Havells / Bajaj / Syska / Crompton. Type 1 Point Wiring (upto 12 Metres)

Supplying, Installation, Testing & Successful Commissioning of 36 Watts 4 Feet LED Batten Light (Day Cool) complete with internal wiring, 1 metre length of any standard make rated 3 core copper wire etc.,, ready to use suitable to fix on wall / ceiling and to work with 230V Single Phase, 50Hz AC Supply. The end wire from the fitting shall be terminated to a 2 Way 5Amps PVC Connector and to connect to the existing point. LED Fitting Make: Philips / Wipro / Havells / Bajaj / Syska.

Supplying, Testing and Successful Commissioning of 3.5 Core x 35.0 sq. mm PVC insulated and PVC sheathed / XLPE aluminium armoured conductor cable of 1.1 KV grade as required. The laying of the following have already been considered under S.Nos: 75. UG Cable Make: CCI / Polycab / Havells / Universal / KEI

Commissioning of 16 Modular GI Box along with Modular Base & Cover Plate for Modular Switches and Sockets in recess / wall using suitable hardwares etc. as required and as per directions of Engineer In-Charge and consisting of following Modular items a) 5/6 Amp Switch - 2 Nos; b) 6 Pin 5/6 Amp Socket Outlet - 2 Nos; c) 15/16 Amp Switch - 2 Nos; d) 6 pin 15/16 Amp Socket Outlet - 2 Nos and e) 20 Amps, 2 Pole, "C" Curve, 10kA, 230V Mini MCB - 1 No. Internal wiring for 5 Amps Switch & Socket with 4.0 sq.mm FRLS Multistrand, Single Core Copper Wire; for 15 Amps Switch & Socket with 6.0 sq.mm FRLS Multistrand, Single Core Copper Wire. Red and Black Colour for Phase and Neutral and 4.0 sq.mm FRLS Multistrand, Single Core Copper Wire, Green Colour for Earthing Loop and terminate all the wires using suitable size Copper Lugs as required. UG Cable Make: CCI / Polycab / Havells / Universal / KEI

Supply, Installation, Testing and Successful Commissioning of 12 Inch Dia, 300 mm sweep, industrial type ready to use Exhaust Fan having Bird Cage with 1.5 FRLS PVC insulated, copper conductor, single core cable and to fix with required size of MS frame duly painted with one coat of primer and 2 coats of paint, suitable hardwares etc., and provide one no. of 3 Pin 5/6 Amps ISI make Socket along with Gangbox and 3 Pin 5/6A Amps ISI make Plugtop as required. Exhaust Fan Make : Crompton / Rally / Usha / Havells / Bajaj / Almonard / Khaitan. Other Items Make: LISHA / GM / L&T / Indo-Asian.

Supply, Installation, Successful Commissioning and Testing of LT Double Door IP55 Indoor Panel Box of size 24" (W) x 36" (H) x 20" (D) made out of 1.6mm thick CRCA sheet steel enclosure, painted with 2 coats of red oxide & 2 coats of Siemens Gray colour paint and consisting of items as mentioned in a) to i). At the bottom of the Panel, 1 x 100A, 30kA, 4P MCCB shall be fixed. The Output from the 100A MCCB shall be connected to 4 x 125A range Copper Bus-Bars using Copper Cable / Copper Bus-Bar. From the Bus-Bar, input shall be tapped for 4 x 40 Amps 4 Pole RCCB through rated FRLS multistrand copper wire using suitable type of lugs and standard colour code of wiring, neatly dressed. All Lighting Circuit (Lights & Fans), Switch Board Cicuits to be connected to this LT Panel. A Separate Aluminium Bus-Bar for connecting the Sub-Circuits Earth Wires in the Panel and extended for 2 Inches outside the Panel on both sides, for connecting Bare Copper Wires from the Earthpit should be provided. 3 Nos of plate cutting for fixing glands, entry and exit of Copper / UG Cable(s), Cable Alley are to be made available. The panel shall be have individual hinges with locking arrangement doors for each MCB / RCCB / MCCB distribution chamber within the compartment. The LT Box shall be mounted on the floor with total stand height of 0.75-1.5 Feet grouted to the floor, doors on front with locking arrangements. The stand portion from the floor on all 4 sides shall be suitable covered with removable type metal sheet (screwed to the stand) painted with same colour as of LT Box. All visible Bus-Bars inside the Panel shall be suitably covered with the 6mm Hylem sheets from. 6" x 6" water proof vents shall be provided on both the sides of the Panel, covered with wire mesh from inside. Important: All incoming / outgoing armoured cables / Sub-Main Circuits shall be terminated with suitable size copper / aluminium lugs (for copper cables / wires, coppler lugs and for aluminium cables / wires, aluminium lugs). During connections, if any Incoming / Outgoing cables is / are need to be extended, part of the work (Cable / Wires for extension of connection will be provided by CSIR-CFTRI). S.No: a), d), e) & i) Make: Any ISI Brand; S.No: b) & c) Make : L&T / ABB / Schneider / Havels. Panel Design: As per Engineer In-Charge. a) Copper Bus Bar of size 40mm x 5 mm insulated with fire proof tape, mounted on Bus Bar Insulators. - 04 Nos., b) 100A, 36KA, 4Pole MCCB - 01 No., c) 40A, 4P RCCB 440V AC with 30mA sensitivity - 04 Nos., d) RYB LED Phase Indication Lamps with Fuse Unit for Input and Output - 2 Sets., e) HT Rubber Mat of 6' x 3' - 01 No. f) Aluminium Earth Bus-Bar 50mm x 5mm - 01 No.

Labour charges for 8 feet depth earth pit below ground level, to dig including hard soil, rocks etc.,if any encountered, fixing the Item No:19, refilling of soil etc., as required. (along with charcoal / coke and salt from S.No:79 as required, already estimated under S.No.79).

Dismantling & taking down Old light Fittings / related wirings, hardwares etc., after carefully disconnecting the incoming electrical input and insulating the same, depositing all the old materials in an organised manner to the Auction / Electrical Section Store Yard or as per the advise of the Electrical Officer In-Charge of the Project without any damage.

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc., as required. Wire Make: Havells / Finolex / Standard / V-Guard / Polycab; PVC Casing-Capping / Conduit Make: VIP / Joegeetha / Supreme / Astral / Polycab / Modi's; Modular Items Make: Legrand / ABB / Crabtree / Siements / Havells / L&T / Schneider. Electrical Engineer In-Charge will give directions. Group A

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc., as required. Wire Make: Havells / Finolex / Standard / V-Guard / Polycab; PVC Casing-Capping / Conduit Make: VIP / Joegeetha / Supreme / Astral / Polycab / Modi's; Modular Items Make: Legrand / ABB / Crabtree / Siements / Havells / L&T / Schneider. Electrical Engineer In-Charge will give directions. Group B

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc., as required. Wire Make: Havells / Finolex / Standard / V-Guard / Polycab; PVC Casing-Capping / Conduit Make: VIP / Joegeetha / Supreme / Astral / Polycab / Modi's; Modular Items Make: Legrand / ABB / Crabtree / Siements / Havells / L&T / Schneider. Electrical Engineer In-Charge will give directions. Group C

Wring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for Wire & Pipe: Same as Item No:66. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for Wire & Pipe: Same as Item No:66. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for Wire & Pipe: Same as Item No:66. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Earthing with GI Plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. Note: Masonry enclosure size is 1.5 Feet x 1.5 Feet x 1.5 Feet. As per IS 3043, charcoal/ coke and salt should be refilled with 50 Kg each per earthpit. The copper plate has to be tinned, connected copper flats have to be brazed and only SS nut, bolts and washers to be used.

Supply and laying 25mm x 5 mm GI Strip 0.5 metre below ground as strip earth electrode, including connection / terminating with GI nut, bolt, spring, washer etc., as required. (Joining shall be done by overlapping and with 2 sets of GI nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with SWG dia G.I in 15mm dia G.I pipe from earth electrode including connection with G.I thimble excavation and refilling as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of Upto 35 sq. mm (clamped with 1mm thick saddle) on wall surface as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Aluminium Lugs and Brass Compression Gland Make: Dowells / Comet / Braco. Note: Each means, all leads at one end of the Cable.

Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerence as per IS: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, earthing etc. complete as required. Ceiling Fan Make: atomberg / orient electric, / Havells / Kuhl / Crompton / Bajaj. Note: a) The fan should have an connectivity option to control the motor speed through Mobile Phone App of both Android & iPhone . b) The fan should have Warm White LED downlight & control for the same should be available in the supplied remote. c) For the chosen make by the contractor from the choice of brand given as in above, the fan colour & model shall be as per the choice of the Engineer Incharge.