Central Food Technological Research Institute Tender

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 M sand)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 M sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm MAKE: SOMANY/ KAJARIA/ NITCO/ RAK

Providing and laying vitrified tiles in floor in different sizes (Minimum thickness of 10 mm) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement : 4 M sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified tiles Matt/Antiskid finish of size Size of Tile 600x600 mm MAKE: SOMANY/ KAJARIA/ RAK/ NITCO

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 M sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm MAKE: SOMANY/ KAJARIA/ RAK/ NITCO

Grouting the joints of flooring tiles having joints of 5 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm Make: Leticrete, Asian Paints or FOSROCK

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/ litre MAKE: asian or its equivalent

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic ompound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats Recommended brand: asian/NEROLAC

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture MAKE: asian - apcolite gloss enamel OR Nerolac – synthetic enamel OR Dulux - Gloss enamel

Providing and fixing tiled False Ceiling of approved materials of size 600x600 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanized @ 170 gsm/sqm) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x32mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross "T" of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main "T"at 600mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.3mm and laying false ceiling tiles of approved texture in the grid including, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications drawings and as directed by Engineer-in-Charge. 9 mm thick square edge PVC Laminated Gypsum Tile of size 600x600 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. The tiles should have Thermal Conductivity k = 0.24 w/m k, Colour white, Fire performance Class 0/Class1 (BS 476 Part 6&7) in module size of 600 x 600 x 9 mm MAKE: ARMGYP SAND (ARMSTRONG)

Providing and fixing factory made uPVC glazed/ wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles having minimum wall thickness of 1.70mm for series R1 & R2 profiles and 2.10 mm for series R3 and R4 profiles conforming to EN: 12608 in any shape colour and design duly reinforced with galvanized mild steel section made of required shape and size as per CPWD specification, uPVC extruded glazing beads, interlocks and inline sas adaptor (where ever required) of appropriage dimension, EPDM gasket, hardware SS 304 grade fasteners of Minimum 8mm dia with counter sunk head, comprixing of matching polyamide PA6 grade sleeve for fixing frame to finished wall as pr IS1367: PART 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/ mechanically jointed duty sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc., After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specificaton and direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-charge. Wire mesh/ Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS:3548 & IS:16231 shall be paid separately. Note: Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed 45 m/ sec as per IS875 - part3 (ii) sits with structure height morethan 20m for all wind speeds two track two panels sliding window with aluminium channel for roller track, wool pile, nylon rollers with SS304 body. Using R2 series with frame (40mm and above) x (40mm and above) and sash (25mm x above) x (50mm & above) with zinc alloy (Zamak) powder coated touch locks with hook (Height upto 1.2 metre) Make: LG / NCK VEKA/ Komarling

Providing and fixing factory made uPVC glazed/ wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles having minimum wall thickness of 1.70mm for series R1 & R2 profiles and 2.10 mm for series R3 and R4 profiles conforming to EN: 12608 in any shape colour and design duly reinforced with galvanized mild steel section made of required shape and size as per CPWD specification, uPVC extruded glazing beads, interlocks and inline sas adaptor (where ever required) of appropriage dimension, EPDM gasket, hardware SS 304 grade fasteners of Minimum 8mm dia with counter sunk head, comprixing of matching polyamide PA6 grade sleeve for fixing frame to finished wall as pr IS1367: PART 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/ mechanically jointed duty sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc., After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specificaton and direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-charge. Wire mesh/ Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS:3548 & IS:16231 shall be paid separately. Note: Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed 45 m/ sec as per IS875 - part3 (ii) sits with structure height morethan 20m for all wind speeds Two and half track three panels sliding window with two glazed and one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS304 body Using R3 series with frames (85mm and above) x (40mm & above) and glazed sash (30mm & above) x (55mm & above) and fly screen sash (20mm & above) x (50mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with Multi-point locking system (Height upto 1.8 metre) Make: LG / NCK VEKA/ Komarling

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) Make: JINDAL

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) Make: JINDAL

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) (Plain) MAKE: SAINT GOBIAN OR MODI

Providing and fixing 9mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass/ stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. MAKE: NOVAPAN

Providing and fixing 220mm long tubular SS handle

Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Make: Godrej

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. Make: Godrej or its equivalent

Providing and fixing SS wire guage (Grade - 304) fly proof mesh (or mosquito mesh) of thickness 0.5 mm dia to 0.63 mm dia of average width of aperture 1.4 mm or less (as decided by the engineer incharge) in UPVC window shutters with necessary screws, fittings etc.,

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 5.00 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 M sand)

Providing and laying cinder filling in sunken floors and other locations with approved quality cinder including watering and light ramming etc. required for proper compaction/ completion of the work complete in all respects as per drawings and as directed by the Engineer-in-Charge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 M sand: 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and fixing below counter wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps Make : Cera or Hindwdare or Parryware

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm MAKE: CERA/ PARRYWARE/HINDWARE

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 M sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing and laying 18mm thick granite stone slab (leather finish) in steps over 20mm thick base

Dismantling G.I pipes (exposed on wall) including all necessary fittings manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge: 15 mm to 40 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm nominal dia Pipes MAKE: SUPREME/ ASHIRWAD/ ASTRAL

Providing and fixing C.P brass two way bib cock 15 mm Make: Jaguar

Providing and fixing P.V.C waste pipe for sink or wash basin or urinals including P.V.C waste fittings complete. Semi rigid pipe 40 mm dia Make: KOHINOOR, ONIDA or its equivalent

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore (600mm)

Providing and fixing CP Coated Brass Angle cock 15 mm Make: ONIDA

Providing and fixing of SWR nahani trap 100 mm dia including adhesive complete Make: Ashirwad / finolex or its equivalent

Providing and fixing 100 mm SS grating with hole Make: ONIDA

Providing, laying and jointing PVC pipes of 6 kgf/ sq.cm pressure capacity including testing of joints etc., complete 63 mm diameter Make: ASHIRWAD/ FINOLEX/ SUPREME

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead for all lead upto 10 kms including all lifts involved.

Part B: Electrical Work

Supplying, Installation, Testing & Successful Commissioning of 36 Watts, 24 Inches x 24 Inches Square Shaped LED Fitting Day Cool White complete with internal wiring, 1 x 2 Way, 5 Amps, PVC Connector, 1 Metre length of any standard make rated 3 core copper wire etc., ready to use and to work with 230V Single Phase, 50Hz AC Supply, suitable to fix on falseceiling with required hardwares. Make for All: Please refer Special Electrical Conditions under Tender Document File.

Supplying, Installation, Testing & Successful Commissioning of 36 Watts 4 Feet LED Batten Light (Day Cool) complete with internal wiring, 1 metre length of any standard make rated 3 core copper wire etc.,, ready to use suitable to fix on wall / ceiling and to work with 230V Single Phase, 50Hz AC Supply. The end wire from the fitting shall be terminated to a 2 Way 5Amps PVC Connector and to connect to the existing point. Make for All: Please refer Special Electrical Conditions under Tender Document File.

Type 1 point wiring (upto 12 Metres) with 2 x 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit or in surface using suitable size box type casing-capping / pvc pipe and its related hardwares, with modular switch, modular plate, suitable GI Box and earthing the light points with 1 x 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc., as required. Make for All: Please refer Special Electrical Conditions under Tender Document File. Note: Electrical Engineer In-Charge will give directions to use casing-caping or pipe as per site requirements.

Type 2 point wiring (above 12 and upto 15 Metres) with 2 x 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit or in surface using suitable size box type casing-capping / pvc pipe and its related hardwares, with modular switch, modular plate, suitable GI Box and earthing the light points with 1 x 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc., as required. Make for All: Please refer Special Electrical Conditions under Tender Document File. Note: Electrical Engineer In-Charge will give directions to use casing-caping or pipe as per site requirements.

Wring for circuit / submain wiring with 4 X 25 sq. mm + 2 X 16 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class suitable size PVC conduit as required. Make for All: Same as Item No. 2.03 Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size.

Supplying, Testing and Successful Commissioning of 3.5 Core x 35.0 sq. mm PVC insulated and PVC sheathed / XLPE aluminium armoured conductor cable of 1.1 KV grade as required. (The laying of the following have already been considered under S.Nos: 2.33.) Make: Please refer Special Electrical Conditions under Tender Document File.

Supplying, Installation, Testing & Successful Commissioning of 16 Modular GI Box along with Modular Base & Cover Plate for Modular Switches and Sockets in recess / wall using suitable hardwares etc. as required and as per directions of Engineer In-Charge and consisting of following Modular items a) 5/6 Amp Switch - 2 Nos; b) 6 Pin 5/6 Amp Socket Outlet - 2 Nos; c) 15/16 Amp Switch - 2 Nos; d) 6 pin 15/16 Amp Socket Outlet - 2 Nos and e) 20 Amps, 2 Pole, "C" Curve, 10kA, 230V Mini MCB - 1 No. Internal wiring for 5 Amps Switch & Socket with 4.0 sq.mm FRLS Multistrand, Single Core Copper Wire; for 15 Amps Switch & Socket with 6.0 sq.mm FRLS Multistrand, Single Core Copper Wire. Red and Black Colour for Phase and Neutral and 4.0 sq.mm FRLS Multistrand, Single Core Copper Wire, Green Colour for Earthing Loop and terminate all the wires using suitable size Copper Lugs as required. Make: Same as Item No:2.03

Supply, Installation, Testing and Successful Commissioning of 12 Inch Dia, 300 mm sweep, industrial type ready to use Exhaust Fan having Bird Cage with 1.5 FRLS PVC insulated, copper conductor, single core cable and to fix with required size of MS frame duly painted with one coat of primer and 2 coats of paint, suitable hardwares etc., and provide one no. of 3 Pin 5/6 Amps ISI make Socket along with Gangbox and 3 Pin 5/6A Amps ISI make Plugtop as required. Make for All: Please refer Special Electrical Conditions under Tender Document File.

Supply, Installation, Testing and Successful Commissioning of 4 + 8 Way Double Door MCB Distribution Box made out 1.6mm thick CRCA sheet steel enclosure, painted with 2 coats of primer & 2 coats of Siemens Gray colour paint, suitable for 440V, AC to fix on surface / recess, complete with Din Rail consisting of 1 x 63Amps 4 Pole RCCB having a sensitivity current 30mA, 3 x 32 Amps 2 Pole MCB, "C" Curve, 10kA Breaking Capacity and blank plates. The output from the RCCB to be connected to the 3 x 32 Amp, 2 Pole, 10kA, "C" Curve MCBs as Input with independent 6.0 sq.mm single core copper wires, duly terminated with copper lugs. The earth wire from the mains should be terminated to the earth bolt / bar in the box with lugs. Make: Please refer Special Electrical Conditions under Tender Document File. Note: Labelling to be done for Input & Output Controls in Paint / Acrylic Sticker.

Single Door IP55 Indoor MCCB Box of size 24" (W) x 30" (H) x 12" (D) made out of 1.6mm thick CRCA sheet steel enclosure, painted with two coats of red oxide & two coats of enamel paint siemens gray colour and consisting of 1 No of 250A, 36KA Range 4P MCCB and 4 x 250A capacity Aluminium Bus-Bars for R,Y,B & N. The Bus-Bars should have minimum 3 sets of holes to connect UG Cables of size from 35 sq.mm to 50 sq.mm. The Box should have provision for mounting on the wall with required hardware arrangements, locking arrangements for door, RYB LED Indicating Lamps, 2 nos of earth bolts on either side of the box, 3 numbers of removable plate at the top / bottom of the box for UG Cable entry, any fire proof sheet to cover the bus-bars, water proof vents on both the sides covered with wire mesh from inside to avoid entry of any insects entering inside the box. MCCB Make: Same as Item No:2.09. Note: Labelling to be done for Input & Output Controls in Paint / Acrylic Sticker.

Single Door IP55 Indoor MCCB Box of size 24" (W) x 30" (H) x 12" (D) made out of 1.6mm thick CRCA sheet steel enclosure, painted with two coats of red oxide & two coats of enamel paint siemens gray colour and consisting of 1 No of 125A, 36KA Range 4P MCCB and 4 x 200A capacity Copper Bus-Bars for R,Y,B & N. The Bus-Bars should have minimum 4 sets of holes to connect Copper Cables / Wires of size from 10.0 sq.mm to 25.0 sq.mm. The Box should have provision for mounting on the wall with required hardware arrangements, locking arrangements for door, RYB LED Indicating Lamps, 2 nos of earth bolts on either side of the box, 3 numbers of removable plate at the top of the box for Cable/Wire entry, any fire proof sheet to cover the bus-bars, water proof vents on both the sides covered with wire mesh from inside to avoid entry of any insects entering inside the box. MCCB Make: Same as Item No:2.09 Note: Labelling to be done for Input & Output Controls in Paint / Acrylic Sticker.

Supply, Installation, Successful Commissioning and Testing of LT Double Door IP55 Indoor Panel Box of size 24" (W) x 36" (H) x 20" (D) made out of 1.6mm thick CRCA sheet steel enclosure, painted with 2 coats of red oxide & 2 coats of Siemens Gray colour paint and consisting of items as mentioned in a) to i). The newly laid 4 x 25 sq.mm Copper Cable shall be terminated as Incoming to 250A MCCB along with 2 x 16 sq.mm for earth wire. The Output from the 250A MCCB shall be connected to 4 x 250A range Individual Copper Cable / Copper Bus-Bars. From the Bus-Bar, input shall be tapped for 4 x 63 Amps 4 Pole RCCB, 4 x 63 Amps 4 Pole MCB, 2 x 32 Amps 4 Pole MCB through rated FRLS multistrand copper wire using suitable type of lugs and standard colour code of wiring, neatly dressed. All new / existing out-going Cables / Circuits to be connected to this LT Panel. A Separate Aluminium Bus-Bar for connecting the Sub-Circuits Earth Wires in the Panel and extended for 2 Inches outside the Panel on both sides, for connecting Bare Copper Wires from the Earthpit should be provided. 4 Nos of plate cutting for fixing glands, entry and exit of Copper / UG Cable(s), Cable Alley are to be made available. The panel shall be have individual hinges with locking arrangement doors for each MCB / RCCB / MCCB distribution chamber within the compartment. The LT Box shall be mounted on the floor with total stand height of 0.75-1.5 Feet grouted to the floor, doors on front with locking arrangements. The stand portion from the floor on all 4 sides shall be suitable covered with removable type metal sheet (screwed to the stand) painted with same colour as of LT Box. All visible Bus-Bars inside the Panel shall be suitably covered with the 6mm Hylem sheets from. 6" x 6" water proof vents shall be provided on both the sides of the Panel, covered with wire mesh from inside. The LT Panel is also included for Supply, Installation, Successfull Commissioning and Testing of 1 number of suitable range Multifunctional 3 Phase, 4 Wire Electronic Trivector Energy Meter with Class 0.1 accuracy, required range of CTs, to read and record upto 250 Amps. a) Copper Bus Bar of size 50mm x 5 mm insulated with fire proof tape, mounted on Bus Bar Insulators. - 04 Nos; b) 250A, 36KA, 4Pole MCCB - 01 No.; c) 63A, 4P RCCB 440V AC with 30mA sensitivity - 04 Nos.; d) 32 A, 4Pole MCB - 02 Nos.; e) 63 A, 4Pole MCB - 02 Nos.; f) RYB LED Phase Indication Lamps with Fuse Unit for Input and Output - 2 Sets.; g) Multifunctional 3 Phase, 4 Wire Electronic Trivector Energy Meter with Class 0.1 Accuracy - 01 No.; h) HT Rubber Mat of 6' x 3' - 01 No.; i) Aluminium Earth Bus-Bar 50mm x 5mm - 01 No. Important: All incoming / outgoing armoured cables / Sub-Main Circuits shall be terminated with suitable size copper / aluminium lugs (for copper cables / wires, coppler lugs and for aluminium cables / wires, aluminium lugs). During connections, if any Incoming / Outgoing cables is / are need to be extended, part of the work (Cable / Wires for extension of connection will be provided by CSIR-CFTRI). S.No: a), f), h) & i) Make: Any ISI Brand; S.No: b) to e) Make: Same as Item No:2.09. Panel Design: As per Engineer In-Charge. Note: Labelling to be done for Input & Output Controls in Paint / Acrylic Sticker.

Supply, Installation, Successful Commissioning and Testing of LT Double Door IP55 Indoor Panel Box of size 24" (W) x36" (H) x 20" (D) made out of 1.6mm thick CRCA sheet steel enclosure, painted with 2 coats of red oxide & 2 coats of Siemens Gray colour paint and consisting of items as mentioned in a) to f). The output from the 20/40KVA UPS shall be terminated as Incoming to 125A MCCB. The Output from the 125 MCCB shall be connected to 4 x 200A range Individual Copper Cable / Copper Bus-Bars. From the Bus-Bar, input shall be tapped for 4 x 63 Amps 4 Pole RCCB through rated FRLS multistrand copper wire using suitable type of lugs and standard colour code of wiring, neatly dressed. All Lighting Circuit (Lights & Fans), Part of the Switch Board Cicuits to be connected to this LT Panel. A Separate Aluminium Bus-Bar for connecting the Sub-Circuits Earth Wires in the Panel and extended for 2 Inches outside the Panel on both sides, for connecting Bare Copper Wires from the Earthpit should be provided. 4 Nos of plate cutting for fixing glands, entry and exit of UG cable(s), Cable Alley are to be made available. The panel shall be have individual hinges with locking arrangement doors for each MCB / RCCB / MCCB distribution chamber within the compartment. The LT Box shall be mounted on the floor with total stand height of 0.75-1.5 Feet grouted to the floor, doors on front with locking arrangements. The stand portion from the floor on all 4 sides shall be suitable covered with removable type metal sheet (screwed to the stand) painted with same colour as of LT Box. All visible Bus-Bars inside the Panel shall be suitably covered with the 6mm Hylem sheets from. 6" x 6" water proof vents shall be provided on both the sides of the Panel, covered with wire mesh from inside. a) Copper Bus Bar of size 50mm x 5 mm insulated with fire proof tape, mounted on Bus Bar Insulators. - 04 Nos.; b) 125A, 36KA, 4Pole MCCB - 01 No.; c) 63A, 4P RCCB 440V AC with 30mA sensitivity - 04 Nos.; d) RYB LED Phase Indication Lamps with Fuse Unit for Input and Output - 2 Sets.; e) HT Rubber Mat of 6' x 3' - 01 No.; f) Aluminium Earth Bus-Bar 50mm x 5mm - 01 No. Important: All incoming / outgoing armoured cables / Sub-Main Circuits shall be terminated with suitable size copper / aluminium lugs (for copper cables / wires, coppler lugs and for aluminium cables / wires, aluminium lugs). During connections, if any Incoming / Outgoing cables is / are need to be extended, part of the work (Cable / Wires for extension of connection will be provided by CSIR-CFTRI). S.No: a), d). e) & f) Make: Any ISI Brand; S.No: b) & c) Make: Same as Item No:2.09. Panel Design: As per Engineer In-Charge. Note: Labelling to be done for Input & Output Control in Paint / Acrylic Sticker.

Labour charges for 8 feet depth earth pit below ground level, to dig including hard soil, rocks etc.,if any encountered, fixing the Item No:19, refilling of soil etc., as required. (along with charcoal / coke and salt from S.No:2.29 as required, already estimated under S.No.2.29).

Dismantling & taking down Old light Fittings / related wirings, hardwares etc., after carefully disconnecting the incoming electrical input and insulating the same, depositing all the old materials in an organised manner to the Auction / Electrical Section Store Yard or as per the advise of the Electrical Officer In-Charge of the Project without any damage.

Wring for circuit/ submain wiring alongwith earth wire with 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for All: Same as Item No:2.03. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring.

Wring for circuit/ submain wiring alongwith earth wire with 2 X 4 sq. mm + 1 X 4 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for All: Same as Item No:2.03. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring.

Wring for circuit/ submain wiring alongwith earth wire with 4 X 4 sq. mm + 2 X 4 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for All: Same as Item No:2.03. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring.

Wring for circuit/ submain wiring alongwith earth wire with 2 X 6 sq. mm + 1 X 6 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for All: Same as Item No:2.03. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring.

Wring for circuit/ submain wiring alongwith earth wire with 4 X 6 sq. mm + 2 X 6 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for All: Same as Item No:2.03. Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring.

Wring for circuit/ submain wiring alongwith earth wire with 4 X 10 sq. mm + 2 X 6 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required. Make for All: Same as Item No:2.03 Note: All start & end point of the wires are to be terminated with "Cu" Lugs of suitable type and size and individual pipes for wiring.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. Make for All: Same as Item No:2.03

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Same as Item No: 2.09. 10 A, 240V, Single Pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Same as Item No: 2.09. 32 A, 240V, Single Pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Same as Item No: 2.09. 32 A, 240V, Double Pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Same as Item No: 2.09. 32 A, 415V, Triple Pole & Neutral (4 Pole)

Supplying and fixing 25 A rating, double pole, (single phase and neutral), 240V, residual current circuit breaker (RCCB) having a sensitivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Same as Item No: 2.09.

Supplying and fixing 40 A rating, double pole, (single phase and neutral), 240V, residual current circuit breaker (RCCB) having a sensitivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Same as Item No: 2.09.

Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. Note: Masonry enclosure size is 1.5 Feet x 1.5 Feet x 1.5 Feet raised with Sand, Cement and Bricks etc., As per IS 3043, charcoal / coke and salt should be refilled with 50 Kg each per earthpit. The copper plate has to be tinned, connected copper flats / solid wire to use only SS nut, bolts and washers.

Providing and laying earth connection from earth electrode with 4.00mm dia copper wire in 15mm G.I. pipefrom earth electrode including connection with copper thimble excavation and refilling as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of Upto 35 sq. mm (clamped with 1mm thick saddle) on wall surface as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerence as per IS: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, earthing etc. complete as required. Make: Please refer Special Electrical Conditions under Tender Document File. Note: a) The fan should have an connectivity option to control the motor speed through Mobile Phone App of both Android & iPhone . b) The fan should have Warm White LED downlight & control for the same should be available in the supplied remote. c) For the chosen make by the contractor from the choice of brand given as in above, the fan colour & model shall be as per the choice of the Engineer Incharge.