Central Food Technological Research Institute Tender

Making rough of the existing flooring surface by scrapping and using mechanical and means preparing the surface rough for laying flooring tile.

Dismantling and fixing of existing aluminium partition including Glass/ Novapean sheet etc. as per instruction of Engineer-in-charge

Removing porcelin laboratory sink of any size including stacking of useful materials within 50 metres lead and disposal of unserviceable materials within 50 metres

15mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 M sand)

Laying Vitrified tiles in floor (antiskid) in different sizes (thickness to be specified by the manufacturer) in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 M sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. (Tiles will be supplied departmentaly) Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600x600 mm

Laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 M sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (Tiles will be supplied departmentaly) Size of Tile 600x600 mm

Providing and fixing tiled False Ceiling of approved materials of size 600x600 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanized @ 170 gsm/sqm) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x32mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross "T" of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main "T"at 600mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.3mm and laying false ceiling tiles of approved texture in the grid including, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications drawings and as directed by Engineer-in-Charge. 9 mm thick square edge PVC Laminated Gypsum Tile of size 600x600 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. The tiles should have Thermal Conductivity k = 0.24 w/m k, Colour white, Fire performance Class 0/Class1 (BS 476 Part 6&7) in module size of 600 x 600 x 9 mm MAKE: ARMGYP DEW DROPS (KNAUF-ARMSTRONG)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps Make : Cera or Hindwdare Tap : Onida

Providing and fixing CP Coated Brass Angle cock 15 mm Make: ONIDA or its equivalent

Providing and fixing SS towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste coupling and 40mm C.P. brass tap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm MAKE: CERA/ PARRYWARE/HINDWARE or its equivalent

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing swan neck / 3-way nozzle taps for laboratory sink Make: Hindware, Cera or its equivalent

Providing and fixing 18 mm thick gang saw cut, antiskid finish, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias staircase steps and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 M sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding, nosing and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour jet black, Cherry/Ruby red/ light brown/ or any colour as instructed by Engineer-in-charge Area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing 40mm thick polished stone slab (Cuddapa) on brick walls of size beyond 0.50 sqm including edges grinding, rubbing and polished edge surface

Providing and fixing factory made PVC door frame made of PVC extruded section of profile size 42X48mm having an overall dimension (tolerance ± 1mm) with wall thickness 2.0mm (± 0.2mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded and 3 nos. staineless steel hinges fixed to the frame for door shutter complete as per manufacturers specification including 24mm thick factory made single/multi panel PVC door shutter reinforced with excellent polymeric reinforcement, shall be water proof, termite proof quality including fixing 2 nos of good quality powder coated aluminium aldrops and 2 nos PVC handles of 150mm length complete as per the manufacturers specification and direction of Engineer-in-charge. (For WC and bath room door shutter) Make : Sintex, Maruthi or its equivalent

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Make: Saint Gobain or its equivalent

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) Make: JINDAL or its equivalent

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) Make: JINDAL or its equivalent

Providing and fixing 9mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass/ stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. MAKE: NOVAPAN or its equivalent

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Make: Godrej (Heavy Duty) or its equivalent

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. Make: Godrej or its equivalent

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) (Plain /Pin Headed glass) MAKE: SAINT GOBIAN OR MODI

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Providing and fixing aluminium handles with SS screws etc. complete as per direction of Engineer-in-charge Powder coated minimum thickness 50 micron aluminium Size 100mm x 10mm length

Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead for all lead upto 10 kms including all lifts involved.