Bruhat Bengaluru Mahanagara Palike Tender

code04 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification

code05 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

code06 - Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

code07 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

code08 - Fabricating providing and erecting in position hot dip galvanised gtae, using 72x72x4.8mm Sq, GI Pipe frame with top pipe bending in heavy duty hydraulic press with sand packing and hot bending to form double arc as per Drawing profile 20mm hot Dip galvanised forged ornamental Design Galvanised in between Sq Rods and heads at top, middle and bottom intermediate supports of 75x12mm and 50x6mm arc bent to hot dip galvanised flats, the work is inclusive of throughing GI Flats sq rods placing welding all the joints including grinding, finishing, metal patty, painting, the rate is inclusive of all materials like GI Sq pipe, forged designs,etc., Heavy duty hinges are made out of 75mm Sq block assembled with 20mm dia bearing in three places for each flop, Heavy duty locking arrangments at tow places including cost of labour, painting, erecting charges, using hoist pulley cranes with all lead and lift, loading, Transportation, unloading, scaffolding charges an all other incidental charges for succesfull completion of the works as per dirction of the engineers in charge of the work.

code09 - Fabricating providing and erecting in position hot dip galvanised Sq. Hallow Poles of 132x132 Heavy Guage of Length 3000mm with MS Hot dip Galvanized Grill Work as per approved design and Drawing of Chief architect. Using 12x75mm galvanized flat for alround frame and 20mm x 20mm galvanized forged design with square for for vertical at 150mm C/C as Shown in the Drawing including providing forged ornamental arrowhead at top and bottom. The Work is Inclusive of throughing flat, sqaure roads, Placing welding all the joints, including grinding, finishing 2coats of anticorrosive paint over one coat of metal primer. The rate is inclusive of all materials like MS Hollow galvanized pipe, flats, forged square rods, cost of labour for all items of work cost painting, welding, cutting, grinding withall lead and lift as per specification including loading and unloading with cost and conveyance of all materials, labour, machinery and incidental chrges for the sucessfull completion of the work as per the direction Engineer- in- charge of the Work. Complete as per Specifications & as directed by Engineer-in-Charge of the Work.

code10 - Providing and laying 60mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Cycle Tracks & Pedestrian Footpaths of approved shape and colour, laid in required pattern and including over 30mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge. (WMM/WBM Base to be paid separately if necessary as per relevant technical specification)

code11 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) Mix 1:2:4 (M15) Using 20 mm nominal size graded crushed coarse aggregates

code12 - Providing and fixing pre cast solid cement concrete kerb stones made out of M20 with top width 114mm and 165mm respectively, 400mm high and 450mm Length with CM 1:3 plastering and finishing cutting, including form work, curing, including cost of all materials, labour, hire charges of machinery, loading, unloading, lead and lift, transportation etc., complete to be laid betwwen travel lane and Cycle Track/ Landscape with all lead, Lift, Loading and unloading complete as per the direction of Engineer in Charge ( form finish concrete and no painting to be done). (Excluding GST & Area Loading Charges)

code13 - Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 600X850 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay (non modular) bricks of class designation 3.5 Extra for depth beyond 45 cm of brick masonry chamber : For 600x850 mm size With common burnt clay (non modular) bricks of class designation 3.5

code14 - Supply of round/square recess/surface mounted rolling type LED Down light with ...... W GU 10 LED Lamp Rib Fabricated from diecast aluminium with white powder coated prewired to mains connector & has swivelling unit of aluminium die cast eye ball & LED Lamp position retained by circular wire spring, with Life of 25000 burning hours & 70 lumen maintenance with CRI 80. Power Input: 220-240V @50/60Hz & Power factor 0.9 along with CE approved. 2years Warranty against any manufacturing defect working under standard electrical condition LED square or round down light 15-18W

code15 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS694:2010Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS694:2010

code16 - Providing and Fixing Polished Grey Granite Slab Benches of Size 5ft width of seating slab with bottom slab of 75mm thick with 1.50ft. With, back rest slab of 50mm thick with 1.50ft depth side and slab of 100mm thick, 2.50ft height including bull nosing of all indges including fixing in CC 1:2:4 including loading and unloading and with all lead and lift etc., complete and executing the work as per the directions of Engineer in Charge of the Work.