Bengaluru Water Supply And Sewerage Board Tender

code04 - Providing and laying Ductile Iron pipes of K9 class conforming to IS 8329:2000 with latest amendments, conveying to work site, rolling and lowering into trenches, laying true to line, level and perfect linking at joints, testing and commissioning, including loading and unloading at both destinations, cutting of pipes wherever necessary, jointing with DI specials (excluding cost of specials) and rubber gaskets, cleaning the socket and spigot end with soap solution, applying soft soap to the socket and spigot ends before insertion of rubber gaskets, jacking and fixing in perfect conditions etc. The cost to include soap solution, soft soap, waste etc. and giving necessary hydraulic test to the required pressure as per ISS with all lead and lifts and cost of all jointing materials. (The contractor will make his own arrangements for water for testing. Earth work excavation in trenches to be measured and paid for seperately) Note: In sewerage projects for internal cement mortal lining ( CML ) of DI pipes, if High Alumina Cement ( HAC ) as recommended in Annexure B clause 16.3 of IS8329:2000 is considered in place of Slag or Sulphate Resistance Cement ( SRC ), the cost of pipes may be increased by 5-6% from the prices listed. For DI K9 pipes, 100mm dia Pipes

code05 - 150mm dia

code06 - 200mm dia

code07 - 300mm dia

code08 - 700mm dia

code09 - Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron (DI) conforming ti IS-1865 with the latest amendments and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings (minimum 2 " O " rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. For PN-10: (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete. For sluice Valve of PN 16.0 and 100mm dia

code10 - 150mm dia

code11 - 200mm dia

code12 - 300mm dia

code13 - 600mm dia

code14 - Providing and fixing kinetic AIR VALVE of PN 16.0 for automatic discharge of accumulate air during working condition, conforming to IS 14845 / EN 1074-4. Body and bonnet of DI conforming to IS-1865 of grade GGG-40/50, seals are made of approved EPDM, SS 304 float, guide and internals. Flange drilling according to IS-1538 with appurtenances. complete. Body and bonnet shall be coated with electrostatically applied epoxy powder coating with a coating thickness of 250 micron both inside and outside etc. complete. 100mm dia

code15 - Providing & Fixing DI MJ Specials such as branches and bends suitable for DI K7 and K9 pipes and CI LA class pipes, as per IS 13382 with latest amendments with complete accessories and fixing at site excluding earth work but including loading, unloading, freight charges etc. complete for. For DI MJ Specials : Collar 100mm dia

code16 - 150mm dia Collar

code17 - Providing Ductile Iron push on special confirming to IS 9523 : 2000 : All DI Flanged MJ Collar : 200mm dia Collars

code18 - 300mm dia Collars

code19 - Manufacturing, providing, trasporting, rolling, lowering, laying, jointing & testing and commissioning of MS specials of minimum 8mm thick such as bends, tail pieces, reduces etc. conforming to IS-7322:1985 with latest amendments and including perfect linking and welding of joints to correct position includng cost and conveyance of materials with all lead and lifts, cost all labour and giving satisfactory hydraulic test as per IS:3589:2001 with latest amendments for test pressure and working pressure both at factory and site etc. complete as per detailed specifications with inside lining two coat of food grade epoxy painting of approved make with Each coat of 250 micron thick (after dry) over one coat of food grade epoxy primer of approved make with minium of 50 micron thick (after dry) and outside 25mm thick coating in CM 1:3 by providing 50x50mm weld mesh including loading and unloading of the pipes for the following category to suit PSC / MS / CI / AC / DI / PVC pipes. The weight of MS shell only by considered before lining and coating for arriving at the rate. The thickness of plate will be specified by the engineer. (Contractor will make his own arrangements for procuring water for testing for: Note: 1) For small works where the C.M. lining is not practicable for inside surface of the pipe, food grade expoxy painting of two coat over one coat of epoxy primer may be proposed and got approved. 2) The above rates are applicable only for pipe works etc. complete.Pipe bends,branches, tail pieces, reducers etc. for upto 500mm dia pipes

code20 - Pipe bends,branches, tail pieces, reducers etc. for above 500mm dia pipe

code21 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50m, and lift upto 1.50m, Including cost of all labour complete as per specifications .

code22 - Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specifications including premixing the Materials with water at OMC in Mechanical Mix Plant carriage of Mixed Materials by tipper to site, laying in Uniform layeras with Paver in Sub base / Base course on well prepared surface & compacting with Vibratory roller to achieve the desired density complete as per Specifications MORTH Specifications

code23 - Dewatering the sewage / storm water by using required HP submersible pump for the diversion of storm during the execution of work considering for One Pump

code24 - Providing & Applying Primer Coat with SS1 Grade Bitumen Emulsionon prepared surface of granular base including cleaning of road surface & spraying primer at the rate of 0.60 Kg/Sq Mtr using Mechanical means complete as per specification MORTH Specification No.502

code25 - Providing & Laying Bituminous Macadam with 100 TPH capacity hot mix plant batch type using crushed aggregates of specified grading premixed with bituminous binder VG-40 @ 3.3% by weight of Mix, transported to site , laid over a previously prepared surface with mechanical paver finisher to the required grade, level & alignment & rolled as per clauses 501.6 and 501.70 to achieve the desired compaction.

code26 - Tack Coat:Providing & Applying Tack coatwith RS1 Bituminous emulsion using emulsion pressure distributor at the rate of 0.20 Kg/Sq.Mtrs on the prepared bituminous surface cleaned with mechanical broom

code27 - Providing & laying Bituminous Concrete with 100 TPH Capacity hot mix plant batch type using crushed aggregates of specified grading , premixed with bituminous binder VG-30 @ 5.2 Percent of mix & filler, transporting the hot mix to work site, laying with mechanical paver finisher to the required grade level & alignmnet, rolling with smooth wheeled , vibratory & tandem rollers to achieve the desired compaction as per MORTH specifications clause No.507 complete in all respects