Bangalore Electricity Supply Company Limited Tender

code04 - FREE STANDING TABLE FOR CABIN - WITHOUT FRAMES Providing and fixing Free Standing Table for Cabin - without frames consisting of 25mm thick PLPB table top, 25mm thick PLPB with edge bomded End table, 18 mm thick PLPB with edge bonded Modesty, Wire manager ABS plastic grommet one number per table Hardware-Minifix assembly and screw leg, as per specifications, drawings and as directed by Engineer in charge. Main Table: 1500 mm W x 750 mm D x 750 mm ht (Post formed table top) Side Table 900mm W x 450 mm D x 750 mm ht.

code05 - Mobile pedestal unit WOODEN providing and fxing 450mmw x 450 mmd x 685 mmht) Mobile pedestal unit- WOODEN with 18mm thick PLPB with edge bonded for body, Two equal drawer and one filing drawer with centralized locking system, Telescopic channels, castors, Handles and lock etc., complete as per specifications, drawings and as directed by Engineer in charge.

code06 - Providing and fixing veneer paneling, over the 50 mmx35 mm sal wood frame work at spacing not exceeding exceeding 600 mm c/c fixed to the wall and top covered out of 4 mm thick approved quality veneer, fixed over 12 mm thick ply of approved brand, termite and water resistant, finished with melamine polish, complete including cost and conveyance of all materials, labour for all items of work HOM etc., complete as per specification.

code07 - Conference table wooden Providing and fixing confernce table consisting of 25 mm thick PLPB table Topedge bounded, 25 mm thick PLPB with edge bonded end table, 18mm thick PLPB with edge bonded modesty, Hardware- Minifix assembly and screw leg., as per specification, drawings and as directed by engineer in charge 4800 mm x 2400 mm x750 mm Ht (20 seater) U shaped with a top width of 600 mm.

code08 - Providing and laying Vitrified tiles with thickness 9-10 mm in different sizes with water absorption less than 0.08 and conforming to I.S. 15622, of approved make, in all colours & shade, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry at 3.3 kg/ m2 including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

code09 - Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 g/m2 (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of equired length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, all as per manufactus, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board

code10 - Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ m2, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GIadjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T- sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer in charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 g/m2 (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending

code11 - Providing & fixing stainless steel 304 grade chejja racks with 50mm sequare pipe of 16 guage for support and stainless steel vertical seuare pipe spaceing 10 cm.

code12 - Providing and fixing of Aluminium composite panel of approved make and colour for wall cladding for Brick/Rcc/stone walls & coloumns/beams with necessary aluminium frame works at required level made out of 50x25x4mm C section or equivalent. The panel should consist of 3mm thick non-halogenated FR grade mineral based polymer 2 hrs fire resist ance as per ASTM E119-12 and clause B, S1, do as per ENT 13501-1sand wiched between 0.50 skins thick aluminium sheet making a total panel thickness of 4mm. The surfaces will be finished with PVDF based coating on topsides and service coating on reverse sides would be in polyester paint. The system shall be fixed using GI brackets, aluminium L cleats and stainless steel bolts and nuts complete with spring washer and cap nuts and all other necessary accessories, sealing shall be done with necessary rods etc., complete

code13 - Providing Acrylic name board on ACP Cladding on Main Entrance Building with embosing lettering words on Name plates of size 20 X 4 made of ACP with BESCOM embulum.

code14 - Providing and fixing wooden storage unit one side laminated with 18mm PLY/PLPB with edge bound for body, 18mm PLY/PLPB with opeanable shutters and individual locking system for shutters 9mm PLY with edge bound for rear portion with hafele fitting hinges, hafele locks, minifix assembly, screw legs, handles and tower bolt. complete as per specification drawings and as directed by engineer incharge PLY STORAGE-900mmx430mmx 2100mm

code15 - Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. G.I. pipes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer in-charge

code16 - Supplying and installing at site Steel Storage Racks of Size: 36ix 15ix 2f6i (w x d x h) made out of slotted angle rack supports of size 40x40mm and thickness 14 G with 3 shelves made out of 18G CR sheets with 4 side bend and additional rib at the bottom. The shelves shall be fixed to the slotted angles using Corner plates with suitable bolts and nuts and heavy duty bushes at bottom. applicable with plated bolts all round. With bushes at the bottom. The rack shall be finished with sprayed enamel paint of approved quality and shade.in enamel paint with all lead, lift and applicable taxes as per design and drawing and direction of Engineer in charge of work.

code17 - Supplying heavy gauge PVC conduit pipe 700 mm thick confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc , and fixing using inverted wood plugs in case of RCC ceiling and RCC wall/ stone structure or rawl plugs in case of brick walls and cement plastering the damaged portion using heavy gauge saddles at an interval of 700mm using NF screws.

code18 - Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694 and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose ength in a wood/PVC round block. complete for each outlet. Short point upto 3Mtr from tapping point to out let via switch box

code19 - Supplying of feet -PVC Batten with integrated LED tube 20/22 W with high quality diffuser with Life of 25000 burning hours & 70 lumen maintenance with CRI 80. Power Input: 220-240Vat 50/60Hz & Power factor 0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition. LED light fitting 1 x 4feet - 20/22 W

code20 - do- LED light fitting 1 x 2 feet - 9/10W

code21 - do- Medium point above 3Mtr upto 6Mtr from tapping point to out let via switch box

code22 - do- Long point above 6Mtr upto 10Mtr from tapping point to out let vias witch box

code23 - EARTHING:-Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit.The pit should be filled with equal proportion of salt and charcoal 150mm all-round the pipe to complete depth. The connection from the pipe to the conduit etc., is to be established through GI wire of size as per ISI specification 7.3.3. of IS732 using 12mm dia bolts, nuts, washers and check nuts etc., the pipe shall have 16 through holes of 12 mm dia

code24 - Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS 8130-1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100 Volts as per IS-694 1990

code25 - Supplying capacitor type ceiling fan complete with down rod blades, shackle, canopies etc., for operation on 230 volts, 50cycles. Single phase AC supply conforming to ISS-374-1979 and with double ball bearing system. 48" Sweep (1200 mm)

code26 - Fixing a ceiling/wall mounting fan of all capacities and all types to the existing S hook with fan regulator to the existing board together supplying and fixing a 5 amps ceiling rose, necessary length of 23 / 0.0076 inch PVC insulated twin twisted copper wire and wiring.

code27 - Extra length of GI pipe of class B 19mm dia for down rod.

code28 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box.2 module

code29 - do- 4 Module

code30 - do- 8 Module

code31 - do- 10-12 Module

code32 - Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS- 694 2010 2.5 sqmm

code33 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.

code34 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6A Three Way socket

code35 - do- 6/16A Universal Socket

code36 - Supplying and drawing UTP-CAT 6E LAN cable.

code37 - Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6A One Way Switch

code38 - Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box. 8 Module

code39 - Electrical, wood work and other fixtures as per firm bill.

code40 - Labour charges for cleaning of floors shifting of tables, chairs and disbursing of waste materials etc., as per the dirictions of the engineer incharge.