Bagalkot Town Development Authority Tender

Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 (P.No.15 ,SI.No.3.6)

Construction of Granular Sub-Base of required grading asper design mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, completeas per clause 401 .(I.No.4.1,P.No.19)

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course onwell prepared surface and compacting with vibratory roller to achieve the desired density ( I.No.4.27, P.No.24)

Tack coat on Granular surface treated with primer Providing and applying tack coat with RS1 Bituminous Emulsion using emulsion pressure distributor at the rate of 0.25 kg/m2 on the prepared bituminous surface cleaned with mechanicalbroom, ( P.29, I.No.5.4)

Providing and laying Bituminous Macadam with 40/60 TPH capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder VG-30 @ 3.4% by weight of mix, transported to site, laid over a previouslyprepared surface with mechanical paver finisher to the requiredgrade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction (I.No.5.8C, P.NO.31)

Providing and laying Semi Dense Bituminous Concrete with 40/60 TPH capacity hot mix plant batch type using crushed aggregates of specified grading premixed with bituminous binder VG-30 @ 5% by weight of mix and filler, transported to site, laid over a previously prepared surface with mechanical paver finisher to the required grade, level and alignment androlled as per MoRTH V revision. (P-145, I-21.A.1)

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 g/\m2 area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35:2015.The finished surface to be level, uniform and free from streaks and holes.. (P-182 I-24.15) ----

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work In all kinds of soils Depth upto 3 m (P.No.8, I.No.1.14.1)

Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge.(The cost of PCC shall be paid extra)600 x 300 x 150 mm Kerb Stone(P.No.146 ,SI.No.6.30)

Providing and laying heavy duty cobble stones 75mm thick interlock pavers, using cement and course sand for manufacture of blocks of approved size, shape and colour with a minimum compressive strength of 281 kg per m2 over 50mm thick sand bed ( average thickness ) and compacting with plate vibrator having 3 tons compaction force thereby forcing part of sand underneath to come up in between joints, final compaction of paver surface joints into its final level, including cost ofmaterials, labour and Usage charges of machinery complete as perspecification( V-II P.No.64 ,SI.No.9.32)

Painting two coats after filling the surface with syntheticenamel paint in all shades on new plastered concretesurfaces (P.No.56 ,SI.No.8.10)

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work In all kinds of soils Depth upto 3 m (P.No.8, I.No.1.14.1)

Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately)Mix 1:3:6 (M10) Using 40 mm nominal size graded crushed coarseaggregates.(P.No.15, I.No.2.1.3)

Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all otherappurtenances required to complete the work as per technicalspecifications.M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (The cost of steel reinforcement & formwork to be paidseparately). (P.No.16, I.No.2.4.2)

Providing Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position, binding and anchoring to adjacent members whereever necessary complete as per Design including cost of material, labour, usage charges complete as per specifications. (The laps and wastages shall not be measured separately)(P.No.84, I.No.11.32)

Fabricating, supplying and erection of 9 Mtr Height (bottom dia 165mm, top dia 75mm, 3mm thick; size of base plate 220mmx220x12mm; 4Nos M20x700mm long 'J' bolts and nuts)…Mtrs long hot dip Galvanized Octagonal pole with BSEN 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, bakelite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47m/sec for …….Mtrs pole in single section and single joint welded as per IS 9595/IS 10178 AWS having dimensions bottom …..mm, top….mm with 3mm thick, suitable base plate and 4Nos of ..... long J bolts along with template and the pole shall be galvanized with not less than 65micron etc As per ASTM-A123., (With out foundation-for foundation details refer prevailing).(P.NO-13 and 153 etc

Supply of LED street light liminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with injection molded polycarbonate/clear glass materials, drelivering superior light output.Rated life burning Hrs 50000 hr@ lumen maitenance of 70%,maximum light intesity should be between 60 degrees to 70 degrees CCT>5500K,IP 66 optical and electrical compartment and impact resistance of complete luminaire>IK08. Power factor >0.9 with mains, surge protection -min 5 kv along with over voltage , overload short circuit /miss wiring protection. compatible for pole mouting with outer dia 40mm to 50mm. universal voltage driver to operate wide voltage range from 100v to 270 V 50/60 H application. Compliance to IS 10322/IEC 60598 ,LM 79 and LM 80 Adherence with Rohs. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools . LED Light fixture with ...... w system power consumption. LED Efficiency >130lm/w, nominal CRI>75. Luminaire manufacturer should have in house facility accredited by NABL/CPRI and any goverment certified agecy and design and development facility certified by ISO 9001:2008. Housing with supplier word mark/name shall be Engraved /Embossing on the die cast housing /body part.warranty of 2 years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacture and Cree/nichia/lumileds/osram make LED sourceLED Street light 70 watts (pwd ele I.NO-12.8.3 P.NO-67

Supplying, and fixing of Hot dip Galvanized M.S.Bracket suitable to out door luminaries and mounted on Octogonal pole using necessery bolts,nuts etc., complete(P.NO-16 I.NO-4.7.2(Singal arm bracket with 1500mm standard 40/50mm dia

d)Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC extruded inner sheet armoured UG LT cable as per IS-1554 OR IS -7098 part-1 Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms as per IS-3975 4 core 16 sqmm

c) Supplying of 1.1 KV LT UG cable XLPE or Heat resistant PVC extruded inner sheet armoured UG LT cable as per IS-1554 OR IS -7098 part-1 Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms as per IS-3975 3.5 core 95 sqmm

Fabricating supplying and mounting MS box made out … SWG suitable for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enameled metal paint etc., complete. (41/38(b)) (P-30, I-5.40.2)

Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. flat … with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint(P-30, I-5.41.2)b) 50x50x6mm (2MtrsX7Panels)

Providing and fixing of 3 mtr decorative street light poles 300x300x12mm foundation bolt M20x700mm long, dia 165.3x3.25mmx3mtrs hot dip galvanizing aluminium casting RGB Led light inside 25 watts , spining plate in top section 190 hole per pole inside PC sheet per pole

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts and wiring complete. Protection of Overload and Short circuit with thermal Magnetic/Microprocessed release and Earth Fault as per IS-13947. ( Icu = Ics)(34-35 four pole(a))(P-26, I-6.5.14.1)a) 100Amps 25kA.

Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947.(P-45, I-6.12.2)b) 40Amps

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 220v A.C. 50 Hz 12/24v D.C.(P-48, I-6.36)

Supplying and fixing Microprocessor based Electronic timer (without contactor,Din Mounting using necessary bolts, nuts and washers etc.,.) 3-120sec.(P-51, I-6.45)

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit … The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc, the pipe shall have 16 through holes of 12 mm dia.(P-55, I-7.1)

Digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete.(As per Civil SR KSRB I-2.(P-62, I-7.9.1)

Providing and filling sand in excavated trenches to cover already laid UG cable to a depth of 150 mm all around the cable (pwd ele SL.NO 6.7 P.NO-41)

Wiring for lighting/power circuit using one of PVC insulated 1100v grade, multistrand Copper conductor single core cable in open or concealed system of wiring .(pwd ele SL.NO 2.3.2 P.NO-5)