Agricultural Produce Market Committee Tender

Supplying PVC/GI flexible conduit pipe 25 mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using NF screws and on either end of the pipe terminated completely as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supply and fixing 12"x9"x1.5" polished wood board made of not less than 15mm thick plank on both sides of not more than 2pieces and fixing the same to the wall using tapered inverted wooden plugs screws. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using 2x1.5Sqmm (Phase& Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet/gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Short point upto 3Mtr from tapping point to out let via switch as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet/gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Medium point above 3Mtr upto 6Mtr from tapping point to out let via switch as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet/gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Long point above 6Mtr upto 10Mtr from tapping point to out let via switch as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand 2.5 Sqmm copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:confirming to latest amendments. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying 6A flush type socket and 6 amps 3/5 Ways flush type SP switch either surface/flush mounting in existing gang box or in 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required as per IS 1293 and IS 3654 as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying & Fixing of 70-150 Watts lamp holder 2 Pin as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying of 2 x4 feet - PVC Batten with integrated LED light fighting - 20/22 W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI > 80. Power Input: 220-240V @ 50/60Hz & Power factor >0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and fixing 4Way SP &N regular MCB distribution boards on wall / wood board / flush mounting using required clamps, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase / 3 phase / single door with powder coated painting. Made out of 14 SWG MS enclosure. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and fixingof 6-32Amps SP miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and fixingof 6-32Amps DP miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipment's on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit … The pit should be filled with equal proportion of salt and charcoal 150mm all-round the pipe to complete depth. The connection from the pipe to the conduit etc., is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and check nuts etc., the pipe shall have 16 through holes of 12 mm dia as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Fabricating, supplying and comprising of 10 No's of Three phase energy bank panel of size 200x160x3 + 200x45x5 + 160x45x5 =168000 Sqcm of MS sheet 16 SWG, 10Mtr of 50X50X6mm Angle iron, 32000Sqcm of Hylum plastic sheet, 1 no of 0-600 V Voltmeter, 1 no of 0-30Amps Ammeter, 1no of Rotary selector switch, 1no of LED panel, 10 no of of Three phase energy meter, 10no of 32Amps TPN MCB, 0.5Mtr of 250Amps Bus Bar, 1 no of 160Amps four pole MCCB, 1 no of 63Amps on load change over switch. (3 phase with 5KW load for ripaning chambers) as per specifications and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and fixing of heavy duty cable glands suitable for 25mm dia UG cable of 1.1 KV class (metal only) as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying 25mm tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and Fixing 50mm class A GI pipe up to 4.5Mtrs. long with a reducing collar of 50x40mm to which, an extension of 250 mm pipe is fixed for 125 or 250/400 watts MV / sodium vapour street light fitting, using suitable clamps, bolts ,nuts, and wiring using suitable capacity wires. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying of 4 core 16 sqmm, 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Labour charges for laying of 6 sqmm to 16 sqmm, 1.1 KV class UG cable in existing trench/duct GI pipe / stoneware pipe / on wall / on pole as required. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Digging of trench In soil (hard) of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete. (As per Civil SR KSRB I-2, P-7) as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and fixing of 40mm class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1KV. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying and fixing L.T. cast Iron pot heads suitable for 1.1 KV class 25Sqmm UG cable filled with necessary bitumen/insulating compound complete with terminals, clamps, bolts, nuts and washers etc. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Fabricating, supplying and erecting swaged tubular pole of height 9Mt (5Mt Hb,165.1mm dia 4.85mm thick x2M Hm, 139.7mm dia 4.50mm thick x 2M Ht,114.3mm dia 3.65mm thick) as per IS 410 SP 32 having three sections, and providing two coats of red oxide paint and finished with two coats of enamelled paint of approved quality and colour and M.S.base plate of suitable size welded at the bottom of the pole(as per IS) and 40mm dia GI / flexible PVC pipe of 1mtr length fitted to the heavy gauge polycarbonate control box including 5way connector of size 167x125x82mm for 7.5M ole/200x160x98mm for remaining length of pole with front opening cover, with locking arrangements and suitable capacity MCB/DP switch, The pole shall be erected in cement concrete work (1:2:4) including excavation and refilling of planting depth of the pole to the ground level and the coping CC shall be up to 0.6M above ground level as per IS 2713 - 7. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supply of 90 W LED streetlight with pressure die cast aluminum housing body with optimal heat sink for better thermal dissipation. Diffuser with injection moulded & is made of polycarbonate material with high transmission indes delivering superior light output . Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70% CCT>5500K, IP 66 optical and electrical compartment & impact rsistance of complete luminare>IK08. power Factor>0.9 with mains current should not be greater than 0.1A to 0.7A & Surge Protection-Min 4KV along with over voltage /Overload, short circuit/miswiring protection. Compatible for pole mounting with outer dia of 40 mm to 50 mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60 Hz application. Over load & short circuit protection ensures reliable operation in spite of problem in output side. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL aproved MCPCB Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools . LED Light fixture with.....W System power consumption. LED Efficiency>130lm/w at 1W & Fixture Efficiency>80lm with nominal CRI>75. Luminaire manufacturer should have in house facility accredited by NABL/CPRI & any Government ISO 9001:2008. Housing with supplier word mark/name shall be Engraved/Embossing on the die cast housing/Body part. Warrantly of 5 years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED source manufacture. Suitable for B1/B2 Roads as per IS 1944 part I & part II . PWD SR.and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying of 3.5 core 95 sqmm, 1.1 KV LT UG cable XLPE or Heat resistant PVC insulated, PVC extruded Inner sheath armoured UG LT cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975 as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Labour charges for laying of 95 sqmm to 150 sqmm, 1.1 KV class UG cable in existing trench/duct GI pipe / stoneware pipe / on wall / on pole as required. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Digging of trench In soil (Ordinary) of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete. (As per Civil SR KSRB I-2, P-7) as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Fabricating, supplying and mounting of MS automatic street light control box of size 120x100x2 no's + 120x40x2 no's + 100x40x2no's =41,600 Sqcm with following component, 12000Sqcm Hylum sheet, 4mts of angle iron, 14 pole 40Amps Power contractor, 1 Micro processor based Astronomical timer complete as per specifications and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Fabrication, Supplying, Erection, Testing and Commissioning of 12 Mtrs long polygon high mast with Single / Multiple telescopic sections having, (minimum overlap distance of 1.5 times of top section) thickness as per BSEN 10025 grade S355 JO /ASTM A572-50 steel sheet plate for shaft suitable to withstand a wind velocity of 47 m/sec as per IS 875 part 3(as per GA Drawing).Base plate as per IS 2062/ASTM A572-50. The mast shall be Galvanized in single Hot-dip as per BSEN ISO 1461/ASTM A123 with an average 70 microns as per IS 2629, and welded as per BS 5135 Single L-Seam joint. The mast shall have 2way head frame with die cast LM-6 pulleys, stainless steel axle, Phosphorus Bronze bearing bush press-fitted with separate guides for 2 runs of 5mmdia, stainless steel wire rope of AISI 304grade 7/19-core, (Factor of Safety as per TR no-7). 2.5sqmm EPR insulated PCP sheathed trailing power cable housed inside the bottom shaft of mast with door having locking arrangement. The mast shall have manual / power tool (Suitable reversible geared motor operating on 230/ 415V, 50Hz, shall be provide above 15 Mtrs mast) The mast shall have lantern of 2 segments, suitable dia with max load carrying capacity as per IS 1239. The mast shall be erected on existing RCC footing. The mast shall be supplied with 3mm thick template, lightning arrester of 1.2m length galvanized pipe with top arrow fitted on top of the head frame cover and GLS type aviation twin lamps fitting with wiring complete. (excluding foundation) as per technical data. as per the standard technical specification of SR and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with 150.W System Power consumption. LED Efficiency>130lm/w, nominal CRI >75. Luminaire manufacturer should have inhouse facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/Lumileds/ Osram make LED Source. as per the standard technical specification of SR and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Digging of trench In C.C. cutting of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete. (As per Civil SR KSRB I-2, P-7) as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

KSRB 2-2.1 : Earthwork excavation by manual means for foundation of buildings, water supply, sanitary lines and electrical conduits either in pits or in trenches 1.5m and above in width, in ordinary soil not exceeding 1.5m. in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation after breaking of clods complete as per specifications. with all lead and lift etc., complete as directed by the Engineer-In-Charge of the workas per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Providing and laying in position plain cement concrete of mix 1:4:8 with OPC cement @ 180kgs, with 40mm and down size graded granite metal coarse aggregates @0.85cum and fine aggregates @ 0.57cum machine mixed, machine mixed, concrete laid in layers not exceeding 15 cms. thick, well compacted, in foundation, including cost of all materials, labour, HOM of machinery, curing complete as per specifications and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Providing and laying in position reinforced cement concrete of Design mix M20 with OPC cement @ 320kgs, with 20mm and down size graded granite metal coarse aggregates @0.69cum and fine aggregtes @ 0.460 cum, with super plasticisers @ 3 liters confirming to is 9103-1999 reafirmed-2008, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation for footings, pedastals, retaining walls, return walls, walls (any thickness) including attached pilasters, columnspillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc., including cost of all materials, labour, HOM of machinery, curing, complete but excluding cost of reinforcement as per specifications and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Providing T.M.T bars Fe 500 steel reinforcement for R.C.C work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of machinery complete as per specifications and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supplying of 32Amps TPST with rewirable porcelain channels in SM enclosure. Made out of 14 SWG powder coated paint of approved colour. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.

Supply and fixing 12"x12"x2" polished wood board made of not less than 15mm thick plank on both sides of not more than 2pieces and fixing the same to the wall using tapered inverted wooden plugs screws. as per the standard technical specification and drawing with all lead and lift etc., complete as directed by the Engineer-In-Charge of work.