Agricultural Produce Market Committee Tender

xtra for Groove cutting in upto 50 mm conduit in brick wall/CC floor to the suitable depth for concealing of Conduit/GI pipe and plastering, finishing upto wall surface complete. (I no 1.7.1/p no 3)

Point wiring using copper wire with switch, Supplying and wiring adopting loop system in existing PVC Conduit /casing casing using copper PVC insulated multi strand 2x1.5Sqmm copper wire with a 6Amps flush type SP control switch shall be fixed on the exisiting plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block.complete for each outlet. Point wiring using class A Materials(copper wire:FINOLEX, SBEE, RR KABLE, POLYCAB, HAVELLS, ANCHOR,V-GUARD; flush type SP control switch: LISHA, ANCHOR, CONA, ELLE,GM. ) Short point upto 3Mtr from tapping point to out let via switch. (I no 2.1.1/p no 5)

Point wiring using copper wire with switch Supplying and wiring adopting loop system in existing PVC Conduit /casing casing using copper PVC insulated multi strand 2x1.5Sqmm copper wire with a 6Amps flush type SP control switch shall be fixed on the exisiting plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block.complete for each outlet. Point wiring using class A Materials(copper wire:FINOLEX, SBEE, RR KABLE, POLYCAB, HAVELLS, ANCHOR,V-GUARD; flush type SP control switch: LISHA,ANCHOR,CONA,ELLE,GM. ) Medium point above 3Mtr up to 6Mtr from tapping point to out let via switch. (I no 2.1.2/p no 5)

Point wiring using copper wire with switch Supplying and wiring adopting loop system in existing PVC Conduit /casing casing using copper PVC insulated multi strand 2x1.5Sqmm copper wire with a 6Amps flush type SP control switch shall be fixed on the exisiting plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block.complete for each outlet. Point wiring using class A Materials(copper wire:FINOLEX, SBEE, RR KABLE, POLYCAB, HAVELLS, ANCHOR,V-GUARD; flush type SP control switch: LISHA, ANCHOR, CONA, ELLE, GM. ) Long point above 6Mtr up to 10Mtr from tapping point to out let via switch. (I no 2.1.3/p no 5)

Supplying 6A flush/projected type socket and a 6 amps flush/ projected type SP switch either surface/flush mounting in a existing gang box or in a 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required. 6Amps 3/5 Way. (I no 3.1.2/p no 15)

Supply and fixing of bakelite D.P/Socket/ switch with/without neon indicator over existing wood board or flush mounting in plastic plates/nitches.as per IS 1293 and IS 3854 16Combined switch and socket with indication. (I no 3.3.4/p no 15)

Wiring for lighting/power circuit using 1.5 sqmm. PVC insulated 1100v grade, muftis and Copper conductor single core cable in open or concealed system of wiring Using Group A Materials. (FINOLEX, SBEE, RR KABLE, POLYCAB, HAVELLS, ANCHOR,V-GUARD). (I no 2.5.2/p no 6)

Wiring for lighting/power circuit using 2.5 sqmm. PVC insulated 1100v grade, muftis and Copper conductor single core cable in open or concealed system of wiring Using Group A Materials. (FINOLEX, SBEE, RR KABLE, POLYCAB, HAVELLS, ANCHOR,V-GUARD). (I no 2.5.3/p no 6)

Wiring for lighting/power circuit using 4 sqmm. PVC insulated 1100v grade, muftis and Copper conductor single core cable in open or concealed system of wiring. Using Group A Materials. (FINOLEX, SBEE, RR KABLE, POLYCAB, HAVELLS, ANCHOR,V-GUARD). (I no 2.5.4/p no 6)

Supplying and fixing PBBC bakelite straight or slant batten holder and wiring, within 60w/230 Volts lamps. (I no 4.2/p no 20)

LED Indoor Supplying of 4' feet - 28 Watts LED Tube Light, PVC Square Batten 28W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI > 80. Power Input: 220-240V @ 50Hz & Power factor >0.9 along with CE approved drivers. 5 years Warranty against any manufacturing defect working under standard electrical condition. (I no 4.29.2/p no 25)

Supplying surface mounted type mirror optic luminaries for Twin 2x28watts fluorescent lamps cross rising of stove enameled deep coloured M.S.low profile housing complete with all accessories and high purity anodized aluminum reflector assembling along with cross louvers including necessary fluorescent tubes with Energy Saving Electronic Ballast. 2x4'-28Watts. (I no 4.9.2 P 21)

Fixing all types and all capacities fluorescent/false ceiling/spot light/ CFL fittings indoor on the wall / ceiling/ rafters / girders using 23/ 0.0076" twin twisted PVC insulated wires, required nos of round blocks and clamps (if required) On wall/ceiling. (I no 17.1.1/p no 108)

supplying capacitor type ceiling fan complete with down rod blades, shackle, canopies etc. for operation on 230 volts, 50 cycles. Single phase AC supply conforming to ISS-374-1979 and with double ball bearing system. (I no 9.3.1.2/p no 78)

Fixing a ceiling/Wall mounting fan of all capacities and all types to the existing S hook with fan regulator to the existing board together with supplying and fixing a 5 amperes ceiling rose, necessary length of 23 / 0.0076 inch PVC insulated twin twisted copper wire and wiring completely. (I no 17.8/p no 108)

Supplying and fixing sheet metal box made out of 18 SWG 200x200x65 MM sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. (I no 1.4.7/p no 2)

Supplying 4mm thick plastic sheet with necessary nitches for fixing switches, regulators etc., and fixing on existing wooden or metal box using N.F. screws. (I no 3.9/p no 17)

Supplying and fixing regular MCB distribution boards on wall / woodboard /flush mounting using required clamps, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase / 3 phase / single door with powder coated painting etc., complete       12Way SP &N      Group 'A'. (I no 6.17.3/p no 47)

Supplying and fixing miniature circuit breakers 5-32Amps DP Group 'A' (LEGRAND, ABB, MG, L &T, HPL Molar.) on existing MCB distribution boards using necessary fixing materials and wiring complete as required.(I no 6.16.3/p no 47)

Supplying and fixing miniature circuit breakers 5-32Amps TPN Group 'A' (LEGRAND, ABB, MG, L &T, HPL Molar.) on existing MCB distribution boards using necessary fixing materials and wiring complete as required. (I no 6.16.5/p no 47)

Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit … The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc, the pipe shall have 16 through holes of 12 mm dia. (I no 7.1/p no 55)

Supplying of LT UG 4 core 25 sqmm Class `B’ PVC Cable cable having aluminium conductor PVC insulated, sheathed, galvanised, steel wire/steel tap armoured cable with PVC outer sheathing 1.1 KV class. (I no 7.4.5/p no 55)

Labour charges for laying of 25 sqmm to 75 sqmm ,1.1 KV class UG cable when supplied agency in existing trench GI pipe / stoneware pipe / on wall / on pole as required.In exixting trench/duct. (I no 7.8.2/p no 61)

Digging of trench In Hard Soil of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete.(As per Civil SR KSRB I-2, P-7) (I no 7.9.3/p no 62)

Supplying and fixing of class A (medium duty) 40mm GI pipe of wall thick ness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1 KV class. (I no 7.12.1/p no 62)

supplying and fixing LT cast Iron pot heads suitable for 1.1 kv class UG cable filled with necessary bitumen/insulating compound complete with terminals, clamps, bolts, nuts and washers etc. (I no 7.13.2/p no 62)

Supplying and fixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only) 25MM. (I no 7.14.2/p no 62)

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. 25 sqmm. (I no 7.21.7/p no 64)

Supplying and fixing HRC fuse units upto 32A base on existing switch/panel board. (I no 6.9.1/p no 45)

Supplying and installation/Fixing/Provision of Outdoor type Thermoplastic Modular Panel enclosure with transparent polycarbonate Lid, shock proof, IP65 (Weather Proof) rust proof, dust proof, water proof, corrosion proof, having internally Embedded gasket on both lid and flap suitable to fix Single phase/Three phase Energy Meter in suitable base plate and having a provision for Fuse/MCB cutout with suitable transparent hinged flap opening for operating MCB along with complete tamper proof SEALING facility.300mmx300mmx214mm. (I no 6.42.1/p no 50)

supplying, fixing and wiring electronic 10 to 40 Amps three phase 4 wire class-1 Accuary with Temper proof Energy Meter. (I no 6.33 p no 48)

Supplying PVC/GI flexible conduit pipe 25mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or ravel plugs and clamped using heavy guage saddles at an interval of 300mm using NF screws and the either end of the pipe terminated completely. (I no 1.9.2/p no 3)

Supply of 90 Watts LED streetlight with pressure die cast aluminum housing body with optimal heat sink for better thermal dissipation. Diffuser with injection moulded & is made of polycarbonate material with high transmission indes delivering superior light output . Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70% CCT>5500K, IP 66 optical and electrical compartment & impact rsistance of complete luminare>IK08. power Factor>0.9 with mains current should not be greater than 0.1A to 0.7A & Surge Protection-Min 4KV along with over voltage /Overload, short circuit/miswiring protection. Compatible for pole mounting with outer dia of 40 mm to 50 mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60 Hz application. Over load & short circuit protection ensures reliable operation in spite of problem in output side. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL aproved MCPCB Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools . LED Light fixture with 72 W System power consumption. LED Efficiency>130lm/w at 1W & Fixture Efficiency>80lm with nominal CRI>75. Luminaire manufacturer should have in house facility accredited by NABL/CPRI & any Government ISO 9001:2008. Housing with supplier word mark/name shall be Engraved/Embossing on the die cast housing/Body part. Warrantly of 5 years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED source manufacture. Suitable for B1/B2 Roads as per IS 1944 part I & part II. (I no 4.36.1/p no 27)

Supplying and Fixing of 32mm dia class A GI pipe bracket up to 2 mtrs long bent at suitable angle and fixing to this bracket 1x40/2x40 watts fluorescent tube street light fitting of all capacities to GI or CI or rail or RCC pole / wall using suitable clamps, bolts, and nuts and wiring using suitable capacity wires. (I no 17.1.2/p no 108)

Supplying of 1440 rpm heavy duty exhaust fan with bracket blades complete for light duty suitable to operate on 230V 50Hz, AC supply complete 12" sweep (300mm) (I no 9.1/ p no 78)

Fixing one exhaust fan after making a suitable nitch in the wall and finishing with cement mortar and colouring to match the existing wall or brackets with bolts and nuts and a 5 amps, ceiling rose with sufficient length of 23 / 0.0076 inch PVC insulated twin core wire of approved make with wire mesh and wooden frame if required. (I no 17.11/p no 108)

Supplying and drawing of 3C x 1.5 Sqmm PVC flexible unarmoured copper control cable of Group A approved make (FINOLEX, SBEE, RR KABLE, POLYCAB, HAVELLS, ANCHOR, V-GUARD). (I no 2.8.2/p no 8)

Supplying, installation, testing and commissioning of 200 Litres solar hot water heater comprising of solar flat plate collector of size 2120x1040x100mm and stainless steel hot water storage tank with stainless steel heat exchanger absorber made of copper sheet and copper tube of following capacity aluminum box collector with appropriate capacity electrical back up arrangement excluding inlet and out let pipes. SS Model with 100mm thick of 48Kg/M3 density Rock wool insulation with 22SWG Aluminum cladding. (I no 10.2.1.2/p no 83)

Supply & drawing C PVC pipe 25 MM dia with all fixtures for solar water heater connection with groove cutting, plastering & labour as per civil SR P93, I-13.85.3

Supplying 25 litres capacity vertical/horizontal type wall mounting Eectrical water heater with 22 SWG copper /SS sheet metal inner container tinned inside and anticorrosive paint outside and 20 SWG M.S. sheet metal outer cover between inner and outer container filled with glass wool complete with inlet and outlet pipes so arranged that water flow inside results in water to flow out from the inner container without turbulence. The inner container shall have direct element with a neon indicator fitted with 20A capacity 85. I-10.1.1 P 83

Erection charges for fixing a 25 liters capacity wall mounting boiler (electric geysers) using bolts, flat at one end nut and washers at the other end for through bolts and nuts and washers with 150x450x600mm back plate and wiring complete with 15A 3 pin top of approved make. (I no 17.13.1/p no 109)

Providing & placing Polyethelene Water Storage Tank of 1000 Litres Capacity as per IS with manhole lead & suitable locking arrangements as per Civil SR P 91 I-13.78

Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to table 3 class 5 of IS:8130-1984 and (Virgin) PVC insulation and sheathed suitable for working voltage upto 1100Volts as per IS-694:1990 & confirming to GTP of GROUP-A. 3 core 2.5 sqmm. (I no 2.8.8/p no 8)

Providing & Fixing of push button operated direct on line starter as per Sr I- 247 P XVII

Supplying, installation, testing and commissioning of single phase sub mercible monoblock pump set motor 1 hp/0.75KW's, 230 Volts, 1" output dia with all accessories etc., as per Civil SR PXXXXV/I-1-2

Providing & fixing of M.S. L Type angle iron frame made out of 4 equal angles of 50x50x6mm welded together and fixed at 0.5m c/c in CC (1:2:4) including cost of all materials cutting, bending, scaffolding wherever necessary, nicely finishing the welded joints with all leads and lifts for existing overhead water tank stand rise upto 2Mtrs height with 2 Mtrs width & 2 Mtrs breadth - in between 4 angles both side. As per Civil SR P. No. XI SI. No. 308