Agricultural Produce Market Committee Tender

KSRB 2.5 : Earthwork excavation in all soil deposits and filling sides of foundation upto plinth in layers not exceeding 20cms. in depth, compacting each deposited layer by ramming after watering with all lead and lift including cost of all labour complete as per specifications. specification. No. KBS 2.9.9 / 2.9.10.1 / 2.1.1 Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work Filling.

KSRB 5-11 : Providing and constructing load bearing wall with solid concrete blocks of size 400x200x200 mm having block density not lessthan 1800 kg/m3 and having a minimum average compressive strength 5.00 N/mm2 confirming to IS 2185 (Part) : 2005 and constructed with CM 1:4 , as per IS 2572:2005 including cost of all materials, labour charegs, scaffolding, curing complete as per specifications. KBS No.5.4 Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB 2.8 : Providing and Filling in foundation with granite / trap broken metal 100mm. and down size, with approved sand including hand packing, ramming, watering, including cost of all materials and labour with all lead and lift. complete as per specifications. specification. No. KBS Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB 4-1.2 : Providing and laying in position plain cement concrete of mix 1:4:8 with OPC cement @ 180kgs, with 40mm and down size graded granite metal coarse aggregates @ 0.85cum and fine aggregtes @ 0.57cum machine mixed, concrete laid in layers not exceeding 15 cms. thick, well compacted, in foundation and plinth, including cost of all materials, labour, HOM of machinery, curing complete as per specification. Specification No. KBS 4.1, 4.2 Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB 4-1.5 : Providing and laying in position plain cement concrete of mix M20 with OPC cement @ 300kgs, with 20mm and down size graded granite metal coarse aggregates @0.69cum and fine aggregtes @ 0.43cum, machine mixed, concrete laid in layers not exceeding 15 cms. thick, well compacted, in foundation, plinth and cills, including cost of all materials, labour, HOM of machinery, curing complete as per specifications. Specification No. KBS 4.1, 4.2 Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB 7.9 : Providing and fixing M.S.grill work for windows and ventilators weighing 21kg/sqm using M.S. flats, or M.S. square rods, or combination of M.S. flats and square rods as per approved design, drawing including cutting steel sections and welding the same to required pattern with a coat of red lead primer, cost of materials, fixtures, labour and HOM of machinery complete as per specifications. Specification No. KBS 7.12. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Providing and fixing 12.5mm to 25 mm expanded metal work of 14 gauge with Mathi or Nandi wood patties of 50 mm x 12 mm size, including two coats approved paint etc., complete. (Including cost of screws). Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB 7.10 : Providing and fixing in position aluminium windows and ventilators as per approved drawings with sliding shutters using double track window frame section of size 61.85x31.75mm. with 1.2mm thick, bottom section weight 0.695 kg/m, sides and top sections 1.3 mm. thick weight 0.659 kg/m; and shutter comprising top and bottom section of size 40mmx18mm, 1.25mm thick 0.417 kg./m; shutter outer side 40mmx18mm, 1.25mm.thick weight 0.417 kg/m, shutter interlock section 40mmx26.7mm, 1.1mm thick, weight 0.469 kg/m. the shutters mounted on nylon rollers with approved quality of fixtures such as aluminium handles tower bolts etc.; and providing and fixing 5.5mm. thick plain glass for shutters fitted with rubber beading aluminium sections including cutting to required length, joints mitred subdividing the frame tenonned and rivetted in the assembled frame stiffened with end clips at corners angles etc., and fixed to the walls, lintels, floor beams/cills as the case may be with necessary steel screws, raul plugs, or teak wood gatties including cutting masonry or concrete and making good the original surface using cement mortar, aluminium sections pretreated for removal of any Specification No. KBS using aluminium section anodized to 12 - 15 microns. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Providing and fixing pull and push Rolling shutters of approved make out of 18 gauge.75mm wide cold rolled steel laths of convex corrugation,with side guide and bottom rails, with interlocking arrangements for steel laths by means of alternate clips, suspension shaft with high tension coil type springs two numbers, mounted on specially designed pipes shaft,with bracket plates,guide channel, ball bearing arrangements, for inside and outside locking with push & pull operations complete including pulling hooks, 4nos. handles with all fitting and accessories, painted with a coat of red lead paint(without top cover) cost of materail, labour, HOM of machinery complete as per specifications. (PWD S.R.2018-19 /P.no 33/7.5)

KSRB 7.6 : Providing and fixing top covers made out of 20 guage M.S. sheet over pull and push rolling shutters bent to shape including cot of red lead primer coat of painting, materials, labour, HOM of machinery complete as per specifications. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Fabricating, supplying and erecting M.S. TubularTruss of span upto 10m. The bottom and top member is provided with 50x50x6mm double equal angles, welded back to back and in between top and bottom line, in areas of mid section is provided with 50x50x6mm equal single angle for vertical and inclined members and at supporting ends 40x40x5mm single angle is provided. All the members are welded together with 6mm gusset plate as per Drawing. The entire truss is anchored in RCC column by using 4 Nos. of M.S. anchor bolts at each support, with 10mm thick base plate and shoe plate.The work includes cutting, straightening, placing in position of M.S angle and wleding wherever necessary, and applying one coat of red oxide primer coat to all themembers including cost of all materials, labour charges, and hire charges of machineries for cutting, welding, grinding and erection equipments, with all lead and lift, transportation, etc., complete as per specification. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Providing and fixing Colour Coated Galuvalium (galuvalium sheet) sheet of 0.47 to 0.50mm total thickness (Al-Zn alloy) over the busstand platform beams (MS tubular truss and purlins) at a height of 5m From the floor level etc., including providing and fixing extra sheet for over lapping the main sheet as (0.10 to 0.20m width) requird etc., complete including providing and fixing colour coated Galuvalium (galuvalium sheet) sheet of 0.47 to 0.50mm thickness for gutter etc., complete including Providing and fixing the sheet with self screwing steel screws with rubber washers and including cost of crimp curve charges etc., comlete., Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Providing and installing of approved make pre painted Galvalume iron Accessories, like, plain, ridges, plain gutter, plain flashing, corner Trim, etc. The total coated thickness (TCT) of the sheet shall be 0.47 mm +/- 0.02 tolerance mm Zinc-Alu Alloy coating AZ 150 gsm as per ASTM 1397/755 -550 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 20-22 microns using self drilling / self tapping screws of 25 mm length. (width upto 500-600 mm only), to be fixed over the existing purlins, rafters, channels and trusses. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB15-3.2 : Providing 12mm thick cement plaster in single coat with cement mortar 1:4, to brick masonry including rounding off corners wherever required smooth rendering, : Providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB15-7 : Providing lime rendering for plastering to wall and ceiling, including cost of materials, labour, curing complete as per specifications.and directions of the engineer incharge of the work

KSRB 15.3.8 : Providing 18mm thick cement plaster in single coat with cement mortar 1:4, to brick masonry including rounding off corners wherever required smooth rendering, : Providing and removing scaffolding, including cost of materials, labour, curing, complete as per specifications. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB 15.14.1 : Providing and applying two coats with oil bound washable distemper of approved brand and shade on wall surface including priming coat with distemper primer after throughly brooming the surface free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour, complete as per specifications. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Providing and finishing external walls in two coats over one coat of primer with antifungal paint of approved brand and shade to give an even shade after thoroughly brooming the surface to remove all dirt and loose powdered material, free from mortar drops and other foreign matter cost of materials, labour, complete as per specifications. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

KSRB 15-18.2: Providing and applying enamel metal paint two coats (excluding priming coat) over new steel or other metal surface brushing to give an even shade after cleaning oil, grease, dirt and other foreign matter, including cost of materials, labour, complete as per specifications. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work enamel metal paint.

Providing and laying Hassan Green granite flooring for staircase, treads and rises using pre polished 20 mm thick water cut green Granite slab laid over existing cement concrete bed in CM 1:3, average 20mm thick including full rounding for nosing , cutting 3 line grooves not more than 2 mm wide for antiskidding, curing etc.,complete. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying heavy gauge PVC conduit pipe 19/20mm dia 2mm thick confirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods should be covered using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclousers, run with 18SWG GI fish wire wherever necessary. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and fixing metal fan box with round hook. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Wiring for lighting/power circuit using 1.5 Sqmm FRLS PVC insulated 1100V grade, multistrand copper with low conductor resistance single core wire in open or concealed system of wiring with specified IS-694:1990 & confirming to GTP of GROUP A. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Wiring for lighting/power circuit using 2.5 Sqmm FRLS PVC insulated 1100V grade, multistrand copper with low conductor resistance single core wire in open or concealed system of wiring with specified IS-694:1990 & confirming to GTP of GROUP A. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Wiring for lighting/power circuit using 4.0 Sqmm FRLS PVC insulated 1100V grade, multistrand copper with low conductor resistance single core wire in open or concealed system of wiring with specified IS-694:1990 & confirming to GTP of GROUP A. Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and flush mounting powder coated/galvanised metal box suitable for mounting modular switch plate. The box should be firmly flush mounted after due groove cutting in Brick/Stone/CC wall 4-5 way Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and flush mounting powder coated/galvanised metal box suitable for mounting modular switch plate. The box should be firmly flush mounted after due groove cutting in Brick/Stone/CC wall 8 way Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and flush mounting powder coated/galvanised metal box suitable for mounting modular switch plate. The box should be firmly flush mounted after due groove cutting in Brick/Stone/CC wall 10-12 way Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and fixing superior quality 4 modlue modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing metal/PVC box Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and fixing superior quality 8 modlue modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing metal/PVC box Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and fixing superior quality 10-12 modlue modular switch mounting polycarbonate plate with necessary supporting back plate with required Nos of machine screws, bolts nuts etc., complete on the existing metal/PVC box Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and fixing of Group A 600watts dimmer on existing modular switch plate as per IS 3854 and IS 1293.Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying and fixing of Group A 32amps DP switch on existing modular switch plate as per IS 3854 and IS 1293 Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work

Supplying capacitor type ceiling fan complete with down rod blades, shackle, canaopies etc., for operation on 230volts, 50 cycles. Single phase AC supply confirming to ISS-374-1979 and with double ball bearing system. 48" sweep (1200mm) regular model Item rate is inclusive of all lead and lifts, loading and unloading, as per specifications and directions of the engineer incharge of the work