State Building Construction Corporation Limited Tender
Search from across the categories, cities, and authorities to find the latest Jharkhand tenders. Every Jharkhand tender is curated from credible sources of government websites (eProcurement Jharkhand portal) and newspapers, thus ensuring the credibility of the information presented to you. For more information on Jharkhand tender bidder registration, the login process and more read the FAQs section on this page.
Costs
EMD
₹ 10,16,000Document Cost
₹ 10,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_JSBCC_79593_1Bid Award Id
ViewTender No
JSBCCL/87/2023-24Tender Authority
State Building Construction Corporation Limited ViewPurchaser Address
-Website
http://jharkhandtenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and 1.5M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)
179.16
-
-
Providing designation 75B one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I.
2368.02
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)
10.26
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size
2.52
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size
29.25
-
-
Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
5.61
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
194.34
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
174.66
-
-
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)
8.07
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete
353.67
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts
320.28
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform
56.55
-
-
Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)
11.82
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers
513.51
-
-
Providing TMT reinforcement of following dia rods as per approved design and drawing including carriage of M.S. rods of (Straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.
-
-
-
8 mm dia (19 %of total reinforcement)
5.25
-
-
10mm dia (17%of total reinforcement)
4.39
-
-
12mm dia (17%of total reinforcement)
4.41
-
-
16 mm dia (30 % of total reinforcement)
7.93
-
-
20 & 25 dia(17 %of total reinforcement)
4.41
-
-
Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.
230.01
-
-
Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.
230.01
-
-
Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of
the cover to be not less than 58 kg
6
-
-
Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay F.P.S. (non modular) bricks of class designation 7.5
3
-
-
Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.
120
-
-
Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)
221.94
-
-
Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).
801.75
-
-
Providing designation 75A work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.
45.63
-
-
Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.
158.55
-
-
Providing 125mm thick reinforced designation 75A brickwork in C.M. (1:4) in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as sper building specification and direction of E/I.
19.8
-
-
Providing and laying damp proof course 50 mm thick with cement concrete 1:2:4 (1cement : 2 coarse sand (zone-lll) : 4 graded stone aggregate 20 mm nominal size).
176.58
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes
128224.41
-
-
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
4079.25
-
-
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
4079.25
-
-
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets,
gates and similar work
18232.26
-
-
Providing & Fixing of 50 mm thick Puff Insulated normal tongue & groove type Internal Wall Panel with all required flashings and accessories for fixing outter wall in vertical manner::Continuous line PUF insulated tongue & Groove Partition wall Panel-Both Inner 0.4mm/0.5 mm TCT PPGL sheet 300 MPA with RMP paint in microribbing finishThe PUF panel should be manufactured on state-of-the-art continuous line using N-Pantene as blowing agent which is CFC free Zero Ozone depleting and environment friendly. Manufacturing Plant shall have ISO 9001, 14001 & 45001 certifications.FAB WallPanel shall have Polyurethane Foam confirming to IS 12436:1988. The pre coated sheet shall be of minimum 300 MPA steel grade confirming to IS 14246:1995 and shall have zinc coating of minimum 150 gsm as per IS: 277: 1992, RMP coated, 5-7 microns epoxy primer on both side of the sheet and polyester topcoat of 15-18 micron.All corners to be selaed using corners panels only of same outer wallsecifications to minimize flasings at corners.The top & bottom PPGL sheet with RMP finish. The sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation.
3470.4
-
-
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
54
-
-
roviding & Fixing of min 50mm / 80 mm thick PUF Roof Panel: Continuous line PUF insulated corrugated Panel with max pitch height of 35mm at max center to center distance of 250mmOuter 0.5mm/0.6 mm TCT PPGL corrugated sheet 300 MPA with RMP paint finish in 150 GSM Roof Panels-Inner 0.4mm/0.5 mm TCT PPGL sheet 300 MPA with RMP paint finish in 150 GSM The PUF panel shall be manufactured on Continuous line running on uninterrupted power supply. 85mm PUF roof Panel includes crest height and shall have pre coated Gl sheet on both side of Puf. The pre coated sheet shall be of minimum 300 Mpa steel grade confirming to IS 14246:1995 and shall have zinc coating of minimum 150 gsm as per IS 277: 1992, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micron. The PPGI sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. The PU Foam shall be self-extinguishing type confirming to IS 12436
2762.1
-
-
Providing & Fixing of 50 mm thick Puff Insulted Isoclad (hidden & fix) Outer Wall Panel with required flashings and accessories for fixing outter wall in horizonal manner.Continuous line insulated hid & fix (no screw visible) type wall Panel- Outer 0.5mm/0.6 mm TCT PPGL sheet 300 MPA with RMP paint in microribbingfinish- Inner 0.4mm/0.5mm TCT PPGL sheet 300 MPA with RMP paint in microribbingfinishThe PUF panel should be manufactured on state-of-the-art continuous line using N-Pantene as blowing agent which is CFC free Zero Ozone depleting and Benvironment friendly. Manufacturing Plant shall have ISO 9001, 14001 & 45001 all certifications.Panel shall have Polyurethane Foam confirming to IS 12436:1988. The pre coated sheet shall be of minimum 300 MPA steel grade confirming to IS 14246:1995 and shall have zinc coating of minimum 150 gsm as per IS: 277: 1992, RMP coated, 5-7 microns epoxy primer on both side of the sheet and polyester topcoat of 15-18 micron.
Panel shall be joined together using Hid & Fix joinery and shall be packed online before the transportation to avoid scratches.all corners to be selaed using corners panels only of same outer wall secifications to minimize flasings at corners and between two horizontal fixing of panels snap fit flashing with gasket & slab to be properly fixed to avoid any leakages
1590
-
-
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
-
-
-
Ridges plain (500 - 600mm)
54
-
-
Gutter (600 mm over all girth)
108
-
-
Providing & Applying weather proof sealant on outer joints of approved make confirming to IS & directed by Engineer-in-charge.Sealant 25mmx10mm at joints
886.5
-
-
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.
187.98
-
-
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge
1735.98
-
-
GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece
-
-
-
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
64.5
-
-
Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
9.18
-
-
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm
1629.06
-
-
Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) Dark shade pigment using ordinary cement
120.42
-
-
Supplying , fitting and fixing collapsible gate of apporoved size and make properly fabricated with vertical double channels 20x10x2 mm. at 100mm. Centres and braced with M.S flat diagonals 20 x 3 mm,with top and bottom rails of T. iron 40x40x6 mm with 38 mm dia steel pulleys complete with bolts nuts, locking arrangements stoppers, handles, including applying a primer coat of led paint carriage hosting and taxes all complete as per building specification and direction of E/I.
22.32
-
-
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron
1923.75
-
-
For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
1923.75
-
-
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
207.9
-
-
Providing and fixing 4 mm thick ACP as perdirection of E/I.
185.64
-
-
Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.
69
-
-
Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete. 100x70x4 mm (ordinary type)
333
-
-
roviding and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.
270
-
-
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
24
-
-
Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm
96
-
-
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)
321.3
-
-
Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.
366
-
-
Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
366
-
-
Cairage Of Meterial
-
-
-
Stone metal lead = 22 km
12.36
-
-
Sand 10 KM
572.31
-
-
Aggregate 22KM
450.21
-
-
Brick (7+1)KM
174.81
-
-
Earth 1 Km
2160
-
-
Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. 580mm. long - with 10 litre low level PVC cistern
15
-
-
Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) With "P" trap (a)10 lit. low level P.V.C. cistern
39
-
-
Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.
12
-
-
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth
5.4
-
-
Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.
9
-
-
Providing and fixing C.P. brass bib cock of approved conforming to IS 8931 : 15 mm nominal bore
48
-
-
Providing and fixing C.P.brass long body bib cock of approved quality conforming to standard and weight not less thain 690gms.:15 mm nominal bore.
36
-
-
Providing and fixing PTMT Soap Dish Holder having length of 138 mm breadth 102 mm, height of 75mm with concealed fitting arrangements, Weighing not less then 106 gms.
36
-
-
Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings.
90
-
-
Providing and fixing C.P. extentsion Nipples 15mm size with 12” BSP threads, 70mm length and 30 mm bredth and weight not less than 32 gms
84
-
-
Providing and fixing Mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing.Circular shape 450 mm dia
36
-
-
Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
45
-
-
Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole
111
-
-
Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length
105
-
-
Providing And fixing 32 mm waste pipe for sink or wash basin including P.V.C. waste fittings complete.
39
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the wall etc..
-
-
-
15mm dia
360
-
-
20mm dia
150
-
-
Exposed on Wall
-
-
-
25mm dia
90
-
-
32 mm dia.
150
-
-
40mm dia
180
-
-
Supllying and matarials with lobour for construction inspection chamber of designation class 75b brick deep 600x450 internal diamention having 250mm wall thickness in cement morter(1:6)including 12mm cement plaster (1:4)with punning on inside and cement plaster (1:6)with 600x450mm G.I. cover with frame (weight not less than 36k.g)in foundation and refilling all complete as per specification and direction of E/I.
42
-
-
Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I.
150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.
180
-
-
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
270
-
-
Providing and fixing C.P. brass Stop Cock (concealed) of standard designand of approved make conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings.
198
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
15000
-
-
Providing and fixing PTMT towel rail trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. C.P brass towel rail 20mm x 600mm with bracket container.
36
-
-
Providing and fixing c.p. towel ring complite with brackets fixed to wooden cleats with c.p.brass screws with concealed fitting arangement of approved qualite colour and make.
48
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 178 mm
12
-
-
Providing and fixing Sink Cock With Swinging casted spout
12
-
-
Providing and fixing PTMT/ C.P. swivelling shower,15mm nominal size, 95mm long, 65mm dia. of approved quality, color & make weighing not less than 40 gms with approximate 80 holes of 1.2 mm dia.
30
-
-
provding and laying of 110mm dia. P.V.C. pipe for outlet of water to outlet drain including all accessories ,I.e lubricants, solventcement, clamp, ring, sockets etc.(SUPREME S.W.R.)
90
-
-
provding and laying of 75 mm dia. P.V.C. pipe for outlet of water to outlet drain including all accessories ,I.e lubricants, solventcement, clamp, ring, sockets etc.(SUPREME S.W.R.)
150
-
-
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
-
-
-
i) 110 mm Single tee with door
105
-
-
ii) 110 mm Single tee without door
105
-
-
iii) 110 mm Bend 87.5°
105
-
-
i) 75 mm Single tee with door
105
-
-
ii) 75 mm Single tee without door
105
-
-
iii) 75 mm Bend 87.5°
105
-
-
Providing and fixing ball valve (brass) of approved quality, High or low
pressure, with plastic floats complete :
-
-
-
a) 15 mm nominal bore
6
-
-
b) 20 mm nominal bore
6
-
-
c) 25 mm nominal bore
6
-
-
Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I.
150mm dia
180
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia
90
-
-
Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge
10.02
-
-
Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge
10.02
-
-
Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge
10.02
-
-
DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area
90
-
-
Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.
-
-
-
(a) From 0.00 M to 50.00 M below G.L.
150
-
-
(b) From 51.0 M upto 150.00 M
300
-
-
(b) From 151.0 M upto 200 M
150
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.
200 mm nominal size dia
75
-
-
Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge
6
-
-
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:
200 mm dia
6
-
-
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.
200 mm clamp
6
-
-
Supplying submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages
2 HP
3
-
-
Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914.
F.A.S.D starter upto 5 H.P
3
-
-
3 core PVC insulated PVC sheathed copper conductor flat submersible cable.
Supplying , Flat flexible submersible cable with ,copper conductor , PVC insulated and PVC sheathed as IS:7098
3 Core 4 Sq mm
390
-
-
Supply fitting and fixing GI pipe 50 mm Dia Medium Quaility as per IS:1239 ( part 01 ) 2004
345
-
-
Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required. . Group C
432
-
-
Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.
75
-
-
Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.
54
-
-
Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 2 nos, 3 pin 5/6A modular socket outlet and 2 nos 5/6 A modular switch, connections etc as required.
54
-
-
Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.
33
-
-
Wiring for power plug with 2x4 sqmm FR PVC insulated copper conductor single core cable in recessed PVC conduit alongwith 1 No. 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.
1860
-
-
Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.
-
-
-
2x1.5 Sqmm + 1x1.5 sqmm earth wire
2322
-
-
2x2.5 Sqmm + 1x2.5 sqmm earth wire
1740
-
-
4x6 Sqmm + 2x6 sqmm earth wire
210
-
-
4x10 Sqmm + 2x6 sqmm earth wire PDBs
60
-
-
4x16 Sqmm + 2x6 sqmm earth wire for UPS and battery bank connection
90
-
-
Supplying and fixing Modular type blanking plate-Supplying and fixing modular blanking plate on existing modular plate switch box excluding modular plate etc. as required.
114
-
-
Supply fixing(S/F) following sizes of medium class PVC Conduit along with accesseories in surface/recess including cutting the wall and making good the same in core recessed conduit etc. as required.
-
-
-
20mm
900
-
-
25mm
270
-
-
S/F Modular type Switch / Socket: Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required.
-
-
-
5/6 AMPS, one way switch
57
-
-
5/6 Amps, 3 pin socket outlet
57
-
-
Ceiling Rose: Supplying and fixing 3 pin,5 amp ceiling rose on existing junction box/wooden block including connection etc as required.
180
-
-
Supply and fixing of following size / modules GI box along with modular plate and switches in surface /recess etc as required.
-
-
-
2 module(78 mm x 78 mm)
120
-
-
4 or 5 module(78 mm x 140 mm )
30
-
-
8 or 9 module(78mm x230mm)
30
-
-
ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.
30
-
-
ITC fluorescent fitting with down rods :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, including supplying and fixing ball and socket arrangement, 2 nos. down roda of 20mm dia stee.
48
-
-
S/F Batten Holder: Supplying and fixing batten/angle holder including connection etc. as required.
66
-
-
Supplying and fixing the follwing way Three Pole pole and Neutral Sheet steel M.C.B distribution board, 415 volts in recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, hinged front acrylic cover from MCB Knob detachable gland plate, interconnection including earthing etc. as required(without MCB/RCCB/Isolator).
-
-
-
4 way(4+12) Double door Horizontal type for lighting DBs and 2 in 6A socket+ one for indoor AC unit+UPS
12
-
-
6 way(4+18) Double door Horizontal type( PDB=1)
3
-
-
S/F VERTICAL TYPE TP MCB DB: Supplying and fixing the follwing way s amps urface/ recess mounting , vertical type , 415 volts , TPN MCB distribution board of sheet steel, , dust protected, duly powder coated, completed with 200 tinned copper busbar, common neutral link , earth bus bar, din bar, for mounting MCB detachable gland plate, interconnection including earthing etc. as required(without MCBs and incomer).
-
-
-
4 way(4+12) Double door Verticall type (UPS and Others essential services)
6
-
-
S/F 'MCCB' : Supplying and fixing moulded case circuit breaker with thermomagnetic release and thermal spreaders in existing cubicle panel board complete with connections, testing and commissioning etc, as required. 100A, 16kA as an incomer of VTPN
6
-
-
S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.
-
-
-
6/32A Single Pole
126
-
-
40A TPN MCB
30
-
-
63A TPN MCB
12
-
-
S/F TPN RCCB: S/F four pole, 415 v, residual current circuit breaker(RCCB) , having sensivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc, as required. 40 amps
9
-
-
S/F rewireable double pole/ TP&N switch disconnector: Providing and fixing , following DP/TP&N sheet metal switch disconnector fuse unit in the in the existing metal board with rewireable type fuses, including drilling holes in metal board, making connection etc, as required.
-
-
-
32A , TP&N
9
-
-
63A , TP&N as incomer and one for out going
6
-
-
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
12
-
-
Copper Earth Plate Elecrode:- Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but with charcoal or cock and salt) complete etc. as required. Lightning Conductors=4 nos + Panel=2 nos).
18
-
-
S/L 8 SWG copper wire in ground :- Supplying and laying 8 SWG copper wire at 0.50 metere below ground level for conductor earth electrode, including soldering etc. as required.
150
-
-
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm
330
-
-
Providing and Fixing Lightning Conductor Finial : P/F of lighting conductor finial, made of 25mm dia 300mm long GI tube, having single prong at top, with 85mm dia 6mm thick GI base plate including holes etc. complete as required.
6
-
-
GI lightning conductor tape in horizontal run - Providing and fixing of GI tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required.
390
-
-
GI lightning conductor tape in Vertical run - Providing and fixing of GI tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required.
90
-
-
MV Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 1100V grade with Termination and Laying of cable. For VTPN DB
210
-
-
1.1kV Cable End Termination: suppluing and fixing indoor cable end termination with brass double compression gland and AL lugs of following sizeAl armoured cables.
-
-
-
3.5Cx35 sq.mm
6
-
-
Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 kV grade of size not exceeding 35 sq.mm. on wall surface as required.
210
-
-
Supply of Ceiling BLDC Fan: Supplying, installation, testing and commissioning of 1200 mm (48")Sweep BLDC 5 star, 32W AC ceiling fan confirming to IS: 374: 2019 , including connection with 1.5 sq mm copper wire, down rod of standared length(upto 30cm) withall accessories as required.
114
-
-
Wallmounted Fan 400mm : Supply and fitting of 400mm wall mounted fan including making connection testing, commissioning etc as required.
12
-
-
Supply of Exhaust metal Fan 230mm(9"): Supply and fitting of 230mm(9"), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required.
30
-
-
LED Bulb 9W/10W : Supplying and fixing of LED 9W /10W bulb and accessories as required.
66
-
-
LED tube with Batten 20W: Supply, installation, testing and commissionof wall mounted LED 20W tube light suitable for 230V, single phase supply voltage, with all accessories like batten and electronic driver complete as required.
84
-
-
Recess mounted 20W LED round :Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness 20W LEDs as light source.
162
-
-
LED Flood Light 100W:Supply installation Testing and Commissioning of LED flood lighting( 100W ) luminarie with prssure die cast housing and toughened glass cover (IP-66 protection in existing pole/ pipe for supply voltage 100-270 volts AC, 50Hz. Luminarie shall confirming to IS:10322 part-5/ section -5 and shall be conecessary accessories as per required.
12
-
-
SITC of 3 Phase Online 10 KVA UPS , three phase incoming and three phase output power system of input, voltage range 360V-485 V, frequency range 40-60Hz+1%. Output voltage range 415V+1% , Power factor 0.8/3 :1, harmonic distortion 2%, THD ( linear load): 5% THD( non-linear load)
3
-
-
SITC of 60 Ah SMF Battery, with 24 months replacement gurantee, as per IS:1652:1991
96
-
-
Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.
9
-
-
Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.
120
-
-
Supplying, installation, testing & commissioning of manual call box of ABS type in surface/recess with stainless steel chain & hammer
assembly complete with glass and push button etc. as required
15
-
-
Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in A.B.S. box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.
30
-
-
Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 6 Zone
12
-
-
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.
1230
-
-
Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).
2160
-
-
7.0m height Octagonal Hot -dip glavinized pole(BOP-7030) :Supply, installation of 7.0m height OctagonalHot -dip glavinized pole with top dia 70mm, bottom dia 130mm & made of 3mm thick sheet, base plate dimension 200x200x12mm(L X B X T) including suitable sizes of foundation bolt all complete as required.( without arm).
18
-
-
0.5m single arm suitable for 70mm top pole
18
-
-
Supply and fixing of 70W LED street light fitting ,with die cast aluminium housing of ingress protection of IP65 and complete with all accessories etc on pole including connection and earthing the body etc as required.
18
-
-
Erection of metalic Pole of following length in cement concrete 1:3:6 ( 1 cement:3 coarse sand : 6 graded stone aggregate 40mm nominal size) foundation including excavation and refilling etc as required.
18
-
-
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm
330
-
-
MV Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 1100V grade with Termination and Laying of cable.
-
-
-
3.5CX150 sq. mm armoured AL Cable. For JSEB supply.
150
-
-
3.5CX 95 sq. mm armoured AL Cable.
90
-
-
4CX10 sq. mm armoured AL Cable.( for street light)
600
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm
120
-
-
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm
90
-
-
MV Cable Laying (35 sq mm): Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 kV grade of upto 35 sqmm size direct in ground including excavation and refilling sand cushioning and without protective covering the trench etc as required.
540
-
-
1.1kV Cable End Termination: suppluing and fixing indoor cable end termination with brass double compression gland and AL lugs of following sizeAl armoured cables.
-
-
-
3.5Cx150 sq.mm
6
-
-
3.5Cx95 sq.mm
6
-
-
62.5 kVA DG set :Supply, fitting, fixing, errection and commissioning along with civil foundation work of 62.5 kVA D.G. Set, 415 Volts, 3 Ph. Silent Diesel Engine driven generating set as per IS:1460 & IS : 13018 and alternator as per IS:13364 complete with sound proof company make canopy (Acoustic Enclosure suitable for 62.5 kVA D.G. Set.) with breaker panel (automatic Control Panel) and civil foundation work as per the norms of 62.5 kVA Silent D.G. Set with suitable arrangement for Al./Ar./C etc as required.
3
-
-
Non-Schedule Items
-
-
-
Supply and instullation 1525 millimeter X 760 millimeter (mm LxD) Executive Computer Table , type of Computer Table Computer table with key board drawer and table top, Colour of Top
As per Buyer's Choice, Material of table top,keyboard and drawer Three layer prelaminated particle board(Wood Product) of grade II type II of IS 12823/Latest, Gable end and Modesty panel material Three Layer prelaminated particles board(wood product) of grade II type III of IS 12823/Latest, all complete job, as per direction of E/I.
18
-
-
Supply and instullation Revolving Chair With Arm Centre pivot mechanism (REVOLVING CHAIR), Chair mechanism Centre pivot mechanism, Type of locking:- Tilt limiter , Pedestal Base:- Nylon base, Armrest Material:-Polypropylene , Seat material:- Pressed and moulded with PU foam Backrest is made of:- One piece injection moulded frame all complete job as per direction of E/I.
48
-
-
Supply and instullation Wooden Book Case made up of Commercial Block Board BWP grade Conforming to IS 1659 and 5 shelves, choose all complete job as per direction of E/I.
18
-
-
Supply and instullation Three Seater Meatl Visitor Public Chair Perforated all complete job as per direction of E/I.
24
-
-
Supply and instullation 915 mm wide 1985 mm high Metal Shelving Racks all complete job as per direction of E/I.
18
-
-
Round Stainless Steel Revolving With Foot Rest and Without Back rest all complete job as per direction of E/I.
150
-
-
Supply and instullation Acrylic External Branding Signage Boards, Size 2X1 Feet , (Acrylic Extenal Branding Signage Board, Size 2*1) , all complete job as per direction of E/I.
45
-
-
Supply and instullation Unbranded Acrylic External Branding Signage Boards, Size 2X1 Feet NA (EXTERNAL SIGNAGE BOARD) all complete job as per direction of E/I.
18
-
-
Supply and instullation BEDSIDE CABINET
indian surgical equipmentsR (ISE- 398) , BEDSIDE CABINET indian surgical equipmentsR (ISE- 398) , all complete job as per direction of E/I.
150
-
-
Supply and instullation Non Powered Wheel Chair with Fixed Seat Height Saraswati Scientific (Wheel Chair) Total weight of Wheel Chair (Kg)):- 15, Back rest with Cushion :- Yes, Cushion on Seat With, Leg guard type Fixed, Slope of Seat (Degree):- 185, Type of Back restFoldable, Overall Length (mm):- 950, Foldable:- Yes all complete job as per direction of E/I.
9
-
-
Supply and instullation MS Patient Stretcher Trolley Overall Length of trolley in mm with 5% tolerance :- 1905, Overall width of trolley in mm with 5% tolerance:- 710, Material of Stretcher Trolley:- MS, Provision of mattress:- Yes, Provision of Saline rod :-Yes, Provision of storage tray:- Yes, Number of castor wheels:- 4 , Provision of Oxygen cylinder arrangement :-Yes all complete jobas per direction of E/I.
6
-
-
Supply and instullation one on Top and one in middle & one at bottom above casters (for 3 shelves) Instrument Trolley For Hospitals
Type of Instrument Trolley:- 3 Shelve Instrument trolley, Shelves Position:- one on Top and one in middle & one at bottom above casters (for 3 shelves) , Availbility of Chrome Plated Pressed Sheet Frame:- yes , Foldability:- No Load carrying capacity of the trolley (in kg):- 120 kilogramWeight carrying capacity of the shelves (in kg) :- 40 kilogram all complete job as per direction of E/I.
6
-
-
Supply and instullation Single Layer Foam Mattress - Size 1829 mm x 762 mm KRISHTHAR (M-00254) Product id: 5116877-30128361255 Country Of Origin: India all complete job as per direction of E/I.
150
-
-
Supply and instullation HEALTHCARE CRCA Sheet Perforated Patient Care Beds HEALTHCARER all complete job as per direction of E/I.
150
-
-
Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)
36
-
-
AIR CONDITIONING SYSTEM Supply, installation, testing and commissioning of 1.5 TR, Hot and Cold, 3 star rated (as per BEE) Air Cooled High Wall mounted Inverter type Split Air Conditioner consisting of high wall mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation 4m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. as per the approval of Engineer in Charge
66
-
-
Supply, installation, testing and commissioning of 1 TR, Hot and Cold, 3 star rated (as per BEE) Air Cooled High Wall mounted Inverter type Split Air Conditioner consisting of high wall mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation 4m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. as per the approval of Engineer in Charge
15
-
-
Installation, Testing and commissioning of Wall Mounted Split type High wall indoor units with evaporator coil,fan and fan motor. 1.5TR / 1.0 TR
81
-
-
100kVA Transformer as per IS :1180: Supply, fitting, fixing, commissioning and testing of 100 kVA , 11 kV/0.433 kV Sealed ,Deta/Star, vector group DYn11, outdoor, Oil Cooled Type ONAN off circuit Star Rating Transformer with copper wound Transformer and civil foundation work along with required size & length of MS channels as per the norms 100 kVA outdoor transformer with all accessories as per IS- 1180 of 2014, air filled cable box suitable for 11kV 1 run , 3C 35sqmm XLPE Al. armoured cable for 1.1kV, 1 Run, 3.5Cx150sqmm XLPE Al. armoured cable as required.
3
-
-
Apart- from the above standard fittings followings items should be included:-
-
-
-
Capacity- 100 kVA
-
-
-
Installation - outdoor
-
-
-
No. of phase-Three
-
-
-
Voltage 11kV/433V
-
-
-
Vectro Group -DYn11
-
-
-
Duty- Continuous
-
-
-
Tapping in primary-+/- 5% to -10% in 2.5 steps
-
-
-
Type of Tap changer-OCTC
-
-
-
Cooling - ONAN
-
-
-
Insulation class-A
-
-
-
Temp. rise @ 50 Deg. C. Ambient
-
-
-
Oil by Thermo Meter :- 50 Degree C.
-
-
-
In winding by Resistance :- 55 Degree C.
-
-
-
HT Cable 3Cx35 sq mm :- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 11kV grade.
330
-
-
LT Panel : Supplying, designing, manufacturing, installation, testing and commissioning of panel fabricated out of 2mm thick(14SWG) CRCA sheet steel, dust and vermin proof with reinforcement of suitable size iron channel of suitable size with proper lifting arrangement effecting proper connection of all incomer and out going (IP-43) fully compartmentalized cubical type wall mounted, totally enclosed, switch board and suitable for use on 415V, 3 phase, AC Supply, 4 wire, 50 C/S, system having 25 kA fault capacity, housed with incoming and outgoing aluminum bus bars, interconnection, interlocking between feeders etc. with indicating lamps, push buttons, necessary accessories, all out going feeders protection as required.
3
-
-
The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs
-
-
-
All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminum cables for all MCCB. Panel shall have individual compartment with name plate.
-
-
-
Panel Size - As per Drawing and shall be provided at the time of work order.
-
-
-
The Name Plate for each incoming & outgoing feeder must be in Anodized Aluminium Sheet.
-
-
-
BUS BARS SECTIONS
-
-
-
The panel includes 415V, 200A, 3Ph, 25kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The current density of bus bar shall be minimum 0.8 A /sq.mm. Al. Bars up to 63A capacity. Other inter connections shall be made with 2.5 and 4 Sq mm PVC Cu. wire.
-
-
-
The above panel consisting of the following:-
-
-
-
Note:- All FP/MCCB shall be with thermomagnetic based release type and shall be with spreader links and front rotary handles.
-
-
-
Incomer
-
-
-
1 no-200 ,415V, 4P/36kA MCCB with thermo-magnetic based released type with O/L, S/C protection with adjustable current with spreader links and extended rotary handle.
-
-
-
1 No -100A/FP/25kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. ( incomer for DG suppy)
-
-
-
Electro-mechnical lock for auto changeover -1 set: 100A, 4P
-
-
-
Indicator
-
-
-
Digital Am-meter, three phase
-
-
-
Digital Volt-meter, three phase
-
-
-
CT 500/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set.
-
-
-
Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.
-
-
-
Outgoings
-
-
-
2 nos- 100A FP/16kA, MCCB with thermomagnetic release type and shall be with spreader links and front rotary handles. including suitable arrangement for cable connection on one side and Bus bar connection on other side.
-
-
-
63A TPN/10kA MCB-'C-series'- 4 nos
-
-
-
40A TPN/10kA MCB-'C-series'- 2 nos
-
-
-
AL. bus bar of continious rating 200A
-
-
-
Mechanical items:-Nuts, bolts, washers , doorlocks etc
-
-
-
Electrical Items: Cu wires of different sizes, cable lugs, sleeves, insulators, cable ties, termianls etc+ labour charges
-
-
-
Add 18% GST
18
-
-
Add 1% Labour cess 1%
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements