State Building Construction Corporation Limited Tender
Search from across the categories, cities, and authorities to find the latest Jharkhand tenders. Every Jharkhand tender is curated from credible sources of government websites (eProcurement Jharkhand portal) and newspapers, thus ensuring the credibility of the information presented to you. For more information on Jharkhand tender bidder registration, the login process and more read the FAQs section on this page.
Costs
EMD
₹ 12,45,000Document Cost
₹ 10,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_JSBCC_88954_1Bid Award Id
ViewTender No
JSBCCL/30/2024-25Tender Authority
State Building Construction Corporation Limited ViewPurchaser Address
-Website
http://jharkhandtenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Earth filling in foundation trenches and plinth in layer not exceeding 150 mm thick wall watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trencheed with a lead of 50mm and lift of 1.5 m all complete as per building specification and direction of E/I ( mode of measurement compacted volume )
2038.32
-
-
Providing coarse clean local sand in filling in foundation trench or in pinth including ramming and watering in layer not exceeding 150mm thick with all lead and 1.5 m lift including cost of all material , labous , royality and taxes all complete as per building specification and direction of engineer in charge ( mode of measurement compacted volume)
345.75
-
-
Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l
1587.93
-
-
CONCRETE WORK
-
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)
0.84
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4coarse sand : 8 graded stone aggregate 40 mm nominal size)
242.62
-
-
Providing and laying damp proof course 50mm thick with cement concrete 1:2:4 ( 1cement,2 coarse sand, 4 graded stone 20mm nominal size
2.76
-
-
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.
2139.75
-
-
Plant mix method (Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401) (ii) Rate per cum for grading-II Material
320.96
-
-
Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all omplete as per the direction of Engineer-in-charge.
1179
-
-
Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.
1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
24.6
-
-
RCC WORK
-
-
-
Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20
mm nominal size).
1.87
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
70.9
-
-
Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15' landings, balconies, shelves, chajjas, lintels, bandes, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3(1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).
39.62
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per 18: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).
-
-
-
All works uptp plinth level
512.49
-
-
All works above plinth level upto floor V level
1066.72
-
-
Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))
49.72
-
-
Providing Tor steel reinforcement of 10mm./28 mm / 32mm dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))
33.84
-
-
Providing Tor steel reinforcement of 12mm. /16mm/20mm/25mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))
156.2
-
-
Centering and shutteing including struting, propping etc and removal of form for Foundations, footings, bases for columns, etc for mass concrete
688.85
-
-
Centering and shutteing including struting, propping etc and removal of form for Walls ( any thickness) including attached pilasters, butteresses, plinth and string course etc
60.79
-
-
Centering and shutteing including struting, propping etc and removal of form for Suspended floors,roofs,lancing,balcones and access platform
4094.28
-
-
Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)
3.95
-
-
Centering and shutteing including struting, propping etc and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers
3426.51
-
-
Centering and shutteing including struting, propping etc and removal of form forColumns, Pillars, Piers, abutments, Posts and struts
2382.86
-
-
Centering and shutteing including struting, propping etc and removal of form for Stair , ( excluding landings), except spiral staircase
242.66
-
-
Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). uspended floors, roofs, landing, beams and balconies (Plan area to be measured)
3552.45
-
-
BRICKWORK
-
-
-
Providing designation 75A work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.
72.62
-
-
Providing designation 75 B brickwork in C M ('1 :6 ) in foundation and Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l.
101.47
-
-
Providing designation 100A brickwork with flyash lime brick( flag) confirming to is 12894-1990(9"x4.5"x3") C M ('1 :6 ) in foundation and Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l.
0.55
-
-
Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.
720.04
-
-
Providing designation 112 mm thick reinforced designation 100 A brick work vuith fly ash lirne brick (FLAG)confirming to lS 12894-1990 (9"x4'5"x3" ) in C.M. ( 1 . 4 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials,n caffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specificationand direction of E/|.
3218.8
-
-
Extra for providing and placing 2 no 6mm dia MS bar every 3rd coarse of half brick masonary
3218.8
-
-
WOOD WORK
-
-
-
Supplying fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both side decorative veneered with black board core bended with high quality phenol formal clehydes synihetic resin of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l.
315.95
-
-
Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of
E/l.
2.52
-
-
Supplying fitting and fixing 35mm thick soltd core type decorative double leaf flush door sltutter with both side decorative veneered with black board core bended with high quality phenol formal clehydes synihetic resin of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l.
69.3
-
-
Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :50x12 mm
891.45
-
-
Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc.
complete.
157
-
-
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised
(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
155
-
-
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
146
-
-
STEEL WORK
-
-
-
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
1809.08
-
-
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre
-
-
-
Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)
923.75
-
-
Supplying,frtting and fixing M.S. grill made of 20x6cmm M.S. flat as per approved design and drawing, properly fabrlcated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/1
6469.94
-
-
Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of
E/I.
513.9
-
-
FLOORING WORK
-
-
-
providing and laying, Doublecharge vitrified floor tiles in different sizes (thickness to be specified by lhe manufacturer) with water absorption less than 0.08% and conforming to lS 15622/ISO 13009 of approved make in all cotours and shades, laid on 20mm thick cement mortar 1 4 (1 cement:4 coarse sand) jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching
pigments etc., complete Size of tile 600x600 mm
2403.44
-
-
Providing and fixing granite 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring, kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 SQM
107.53
-
-
Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per
design approved by Engineer-in-Charge.
154.5
-
-
Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing
of cut edges etc. complete.
94
-
-
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineerin-charge and finished smooth.Granite Stone of approved shade
13.2
-
-
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.
293.12
-
-
Providing and laying 1st quality Ceramic glazed wall tiles thickness to be specified by the manufacturer) in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing polishing and cost of curing, taxes and royalty all complete as per building specification and direction of E/I.
1906.67
-
-
Kota stone slab flooring over 25 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :600x600
93.24
-
-
Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including
rubbing and polishing complete.
12.34
-
-
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar
1:4 (1 cement: 4 coarse sand).Medium shade pigment using 50% white cement 50% Grey cement
608.3
-
-
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge
-
-
-
Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent
358.7
-
-
Providing & Fixing flexible Conductive PVC sheet flooring of Armstrong/ Forbo/ Polyflor having a total thickness of 2mm and weight of 3kg/m².Colors and pattern detail shall be dispersed throughout the thickness of the wear layer. It shall conform to Group P of Wear Resistance as per EN 649, Flammability of class Bfl-s1 as per EN 13501-1, Slip resistance as per DIN 51130 group of R9 , having REACH Registration No, 1907/2006 contains no substance mentioned in SVHC list. Impact sound reduction of 3 dB as per ISO 140-8, Residual indentation of 0.05 mm as per EN 433, Color fastness rating ≥6 as per ISO 105-B02, Vertical resistance(R1) less than 1 x 10⁶- 1x 10⁸Ω as per EN 1081, and surface resistance less than 1 x 10⁶- 1x 10⁸ Electrical insulation to ground greater than 50 kΩ as per VDE 0100, Static electrical charge of ≤2.0kV as per EN 1815, Thermal resistance of 0.04m²K/W as per EN 12667, Thermal conductivity of 0.25 W/mK. Equivalent to Armstrong PASTELL. Installation:It is important to ensure the sub floor on which the sheet is being laid is
smooth, flat & hard & free from moisture, grease, etc. In case of uneven sub floor the
-
-
-
The moisture level present in the subfloor should be less than 8% before installation of the floor. The sheet should be laid using adhesive recommended by company.Each row of tiles/strip of floor covering must be linked crosswise with a continuous copper strip. Individual rows/strips must be at least 3 m² in size and linked to the rest of the area with a copper tape. In rooms of up to 40 m², connection points for equipotential bonding should be provided in at least one point in the room.
40.59
-
-
Supply and installation of PVC sheet flooring 2 metre wide and overall thickness of 2mm of Armstrong/ Forbo/ Polyflor. The product should be homogeneous and single layered. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVCwith DIAMOND 10 technology, Plasticizers without DOP, Urethane, color pigments and filler calendered to form a sheet. Product shall conform to group "T" wear resistance as per EN 649, Flammability resistance of class Bfl-s1 as per EN13501-1, Dynamic coefficient of friction of class DS as per EN 13893, Impact sound reduction of 3dB as per ISO 10140, Slip Resistance of class R9 as per DIN 51130, Color fastness rating of ≥6 as per ISO 105-B02, total weight being 3.3 kg/m2 as per EN430. The product shall be suitable for applications in class 23/34/43 areas as per EN685. Product shall exhibit antistatic behaviour, resistance to bacteria,resistance to chemical, resistance to staining,suitability to castor chair.
-
-
-
Installation- It is important to ensure the subfloor on which the sheet is being laid is smooth, flat, hard and free from moisture, grease etc. In case of uneven subfloor the same should be levelled using self leveling compound which will charged extra. The moisture present in the subfloor should be less than 8% before installation of the floor. dhesive. The installation shall be undertaken as per manufacturers installation instructions.
81.59
-
-
Providing and laying of 2 - 3 mm average thick layer of cementations smoothening compound of UZIN NC 149 sh or equivalent as recommended by the Vinyl sheet flooring manufacturer over and including a priming compound of UZIN PE 360 sh or equivalent as recommended by the Vinyl sheet flooring manufacturer and installation team on concrete surface to provide a smooth & homogenous surface for laying of vinyl sheet flooring complete to the entire satisfaction of Engineer-in-charge.
122.18
-
-
P&F flexible PVC sheet wall cladding in 1.00 mm thickness in the size of 1.5 x20mtr with PUR treatment. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVC, Plasticizers, Urethane, color pigments and filler calendared to form a sheet. Colors shall be dispersed throughout the thickness of the wear layer. It should conform to Group M of Wear Resistance as per EN 660-2, Fire resistance of group 2 as per AS/NZS3837, Residual indentation of ≤0.10mm as per EN433, curling after exposure to moisture ≤8mm as per EN434, Seam strength of mean≥240N/50mm as per EN684. Equivalent to Armstrong Walldesign.
375.29
-
-
ROOFING & WATER PROOFING WORK
-
-
-
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design
477.58
-
-
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
39
-
-
Roof/Terrace Water proofing:
-
-
-
Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,material applied with brush, roller or spray for wate proof i n g coating as per manufactlrer specificatio With following steps :-
-
-
-
(a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and
-
-
-
b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured."
-
-
-
(c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, reatiy to-use, flexible cementttious material right angle to the '1st coat over the glass fibre liad surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will be rneasurecl." Alte r three days of drying the 2nd coat, therainwater ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal
-
-
-
d) Protection of treated surface with PCC- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope ( '1:120) towards tlre rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mrn gap betuieen the panel joint. lntegralwater proofing admixture conforming to lS 2645 @ of 100 ml per bag of of cement to be added in the scree d concrete(pard separately for thts ltems).-All corners shall be
-
-
-
(e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc Warranty for Five years
1568.13
-
-
Covering of treated surface wrth PCC :- Providing 25 mm thick Cementn Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,
1568.13
-
-
Providing and mixing Liquid lntergral water proofing compound in Conctrete or plaster as per rnanufacturer specificatioqand as per cjirection of Eng - in Charge Brand- Sika Plastocrate plus, MYK proof WP 1 0, Fosroc-Cc.rnplast X4211 C, Dr fixit Pidiproof LW+ or Equivalent
194.45
-
-
Toilet/Kitchen Water proofing:
-
-
-
1) Surface preparation by grinding machine, cleaning , crack filling etc. complet
-
-
-
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :
-
-
-
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours
-
-
-
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry
191.6
-
-
Providing & fixing Rockfone Stonewool Acotsical Ceiling PACIFIC High NRC (0.80), Fire Rating A1 (EN 13501-1), RH 100% (No visible deflection in high humidity), Superior Class Light Reflection, Sag Resistant 12mm thick Ceiling Tiles of size 600x600 A-Edge (Square) with AntiBacterial Properties & M1 Class Emission Certification made up with Natural Stone (Bassalt Rock) a complete Green Product & perfect suitable for any kind of False Ceiling application in builiding & costruction. The Visible side is a smooth white painted fleece, the Rear side: back fleece with complete
569.5
-
-
FINISHING WORK
-
-
-
Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.
176.43
-
-
Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and
royalty all complete as per specification and direction of E/I.
8724.71
-
-
Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and
royalty all complete as per specification and direction of E/I.
3936.69
-
-
Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.
176.43
-
-
Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and
royalty all complete as per building specification and direction of E/l.
4216.12
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
15081.56
-
-
Providing two coats of oil bond Distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone of fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building
specification direction of E/I
33.48
-
-
Finishing walls with Acrylic Smooth exterior paint of required shade,New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
4804.16
-
-
Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour
10929.25
-
-
Providing two coats of snowcem of approved shade and make over old surface including washing cleaning and preparing the walls, scaffolding , curing and taxes all complete as per building specification and direction of E/I.
1574.26
-
-
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:
818.89
-
-
ALUMINIUM WORK
-
-
-
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for Powder coated aluminium (minimum thickness of powder coating 50 micron)
949.5
-
-
For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)
986.4
-
-
Supplying fitting and fixing glass panes including supplying putty, beads and nails after taking out old and broken glass panes and disposal of debris all complete as per
building specification and direction of E/I. 5.5 mm thick glass panes
197.28
-
-
MISCELLANEOUS WORK
-
-
-
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
408.36
-
-
Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
236
-
-
CARRAIGE OF MATERIALS
-
-
-
SAND (UPTO 10KM LEAD)
1885.6
-
-
CHIPS( UPTO 22 KM LEAD)
1541.88
-
-
METAL ( UPTO 22 KM LEAD)
230.15
-
-
BRICKS ( UPTO 8 KM LEAD )
652.12
-
-
Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 14.14.2-150 mm dia
60
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge
100 mm nominal size dia
30
-
-
Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge
3.34
-
-
Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge
3.34
-
-
Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge
3.34
-
-
DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates)
Drilling upto 30 mtr. Depth below G.L. in Rural Area
30
-
-
BORE WELL
-
-
-
Cost of Drilind 200mmx165mmx125m dia Deep Bore well in all kind of soil and rock in rural area for instalation of pump set with hydrolic DTH rig machine all complete including all materials ,tools ,drilling rig air compressureand equipmentsas well as fuel ,lubricantsand of rig machine and other vehical up to site .
-
-
-
(a) From 0.0m to 50.0 m Below G.L
100
-
-
(b) From 51.0 to 125.0 m Below G.L
150
-
-
(C) From 126M to 150.0 m Below G.L
50
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing(CM) pipe OF Required dia, conforming to IS:12818, including required hire and labour charge , fitting & accessories etc . All complete, for depths as per direction of engineer in charde-200 mm nominal size dia
50
-
-
Development of tube well in accordance with IS : 2800 (partI) IS :11189 to establish maximum rate of usable water yield without sand content ( beyond permissible limit) with required capacity air compressor ,running the compressor for required time till well is fully developed ,measuring yield of well by V notch method or any other approved methode ,mesuring static level & drwan etc by step drawn down method collecting water samples & getting tested in approved laboratory i/c disinfection of tube well all complete hire & labour charges of air compresssor ,tools & accessories stc all as per requirement and direction of engineer in charge.
4
-
-
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well 200 mm dia
4
-
-
Providing and fixing M.S Clamp of required dia to the top of casing pipe of tube well.200 mm dia
4
-
-
Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge
2
-
-
Supply fitting and fixing of standard make starter panel board with arrengement of all neccessery protection including all tax , all complite job as direction of E/I
2
-
-
Supply fitting fixing 3 core 4 sqmm flate copper submersible cable including all tax royalty Etc all complite job as per direction E/I
260
-
-
Supply fitting and fixing lowering 40mm dia G.L column pipe do-do- all complite job as per direction of E/I
230
-
-
Dismantling
-
-
-
Dismantling pucca brick or lime work including stacking servieable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all comlete as per direction of E/I.
166.98
-
-
Taking down old door and window shutters including stacking serviceable materials within 15M. Lead and disposal of unserviceable materials with all leads all complete ap per direction of E/I.
45
-
-
Taking down chaukhats in doors including stacking serviceable materials within 15M. Lead and disposal of unserviceable materials with all leads all complete ap per direction of E/I.
45
-
-
Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars.
46.75
-
-
Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads
including all lifts involved.
313.73
-
-
INTERNAL PLUMBING
-
-
-
SANITARY INSTALLATION
-
-
-
Supplying , fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I 'p' trap 15 liters C.I.pull and let go flushing cistren of names or other I.S.S. equivalent make , complete with all fitting , C.I.or C.C. brackets 32mm alkathene/P.V.C telescopic flush , pipe about 2 M long with one brass coupling and clamps GI ,chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less thane 50grms. 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coats of red oxide primer etc. all
-
-
-
(A) 580 mm. long
-
-
-
(C) With 10 lit. low level PVC Cistem
8
-
-
Supplying, fitting and fixing 40mm high vitreous white glazed earthen E.W.C. with ‘p’ trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete
as per specification and direction of E/I.
-
-
-
(ii) E.W.C. with 'S' trap
-
-
-
(B) 10 lit. low level PVC Cistem
39
-
-
Supplying,fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of ‘Hindustan "Parry" or any other approved I.S.S make with 5 liters capacity C.I. automatic fulsing cistern of reliance for any other I.S.S. approved make with all fittings with C.I.or R.S. brackets, standard size G.I. flush pipe with fitting clamps,15mm C.I. body brass spindle stop cock of approved quality weight not less than 400grams, 15mm P.V.C./Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I.
-
-
-
(a) Flat back or standing corner (600mmx350mm)
8
-
-
Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or
R.S. brackets 32mm C.I.brass waste, 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as
per specification and direction of E/I.
56
-
-
Supplying fitting and fixing white glazed fire’s clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P.brass waste with C.P.brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I.
-
-
-
(i) Kitchen sink 600 mm x 450 mm x 250 mm
12
-
-
Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350gms.) with extra socket all complete as per specification and direction of E/I.
13
-
-
Providing and fixing N.P/C.P. brass /P.V.C. porcelain shower rose of 15mm inlet etc. all complete as per specification and direction of Engineer - in -Charge.(c) 125mm dia
P.V.C shower
11
-
-
(b)Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. Brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror.
-
-
-
(i) 600mm x 450mm size
11
-
-
(c) (i) C.P. brass towel rail 20mm x600mm with bracket container
40
-
-
(c)(iii) C.P. brass liquid soap container
40
-
-
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitionsby cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished
smooth.Granite Stone of approved shade
8
-
-
Provinding and fixing wash basin wih C.I brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereever required :White Vitreous China Wash basin size 550x400 mm with a 15mm CP Brass single hole basin mixer
7
-
-
Providing and fixing white vitreous china laboratory sink with CI brackets , C.P brass chain with rubber plug 40 mm C.P brass waste and 40 mm CP brass trap with necessary C.P brass unions complete including painting of fittings and brackets , cutting and making good the wall wherever required :Size 600x450x200 mm .
2
-
-
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with
S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in charge.
38
-
-
Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete
.Flexible Pipe,32mm Dia
12
-
-
Providing and fixing toilet paper holder :C.P. Brass
39
-
-
Providing and fixing PTMT Bottle Trap for Wash basin. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.
73
-
-
Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms.
37
-
-
Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore
82
-
-
Providing and fixing lead connection pipe with heavy quality brass coupling 2 nos. at both ends etc all complete as per specification and direction of Engineer-in- charge. 15 mm dia and 45 cm long,
9
-
-
Supplying fitting and fixing the following items complete with all materials as per specification and directionof E/I. (a) Glass shelf with C P brass rail, (i) 600×125 mm glass shelf complete
9
-
-
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore
11
-
-
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore.15 mm nominal bore
187
-
-
Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less
than 85 gms
30
-
-
Providing & fixing soap dish holder of approved design.
1
-
-
Providibng and fixing straight type Macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of McAlpine, UK with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector.(supreme/Prince)
38
-
-
Providing and fixing CP brass single lever low flow wall mounted Sink mixer with 15 mm CP brass single lever swivel spout with waste complete with flow rate 2.5 litre per minute at 3 bar including cutting and making good the walls where required. ( MAKE- 1: JAQUAR, MODEL NO. SINK MIXER : FLR-CHR-5163GD ROCA MODEL NO :
G1935A1
7
-
-
Providing and fixing C.P concealed four way diverter with thermostatic mixer with shut off valve and diverter, including cutting and making good the walls, wherever required. (Make:- Jaquar - Four way diverterKUB-35421, Thermostatic mixer 35671 or
Equilent)
11
-
-
Providing & fixing wall mounted 300mm Long SS Grab Bar including cutting & making good the walls. ( MAKE-1: JAQUAR, MODEL NO. GRAB BAR : AKP-CHR-35701PS
ROCA ROCA, MODEL NO : T66041A1
6
-
-
Providing,Fixing wall mounted Double Coat hook on door complete. ( MAKE-1: JAQUAR, MODEL NO. COAT HOOK : AKP-CHR-35761P ROCA MODEL NO :
T6007A1.
34
-
-
Providing, Installing & fixing storage type water heater of approved shade with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working
pressure of 8 kg/sqcm complete as required.
-
-
-
Capacity 25 litres
21
-
-
Capacity 35 litres
1
-
-
DRAINAGE INSTALLATIONS
-
-
-
Providing, Fixing, testing and commissioning of UPVC pipe SWR type 'B' conforms to IS : 13592-1992 with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with
rubber ring joint/solvent weld joint.
-
-
-
75 mm diameter pipe
32
-
-
110 mm diameter pipe
1111
-
-
Providing, Fixing, testing and commissioning of UPVC 'P' trap/floor trap/urinal trap of self cleansing design with or without horn conforming to IS : 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 hard stone ballast 20
mm nominal size) cutting and making good the walls & floors. 110 mm (OD) x 110 mm (OD)
66
-
-
Providing, fixing & testing uPVC pipes, conforming to IS 4985 class 3 (6 kg/cm2) including injection moulded fittings, jointing with solvent cement, cutting and making good the floors and walls and jointing to trap/waste pipe, complete of outer dia.
(Indirect waste) 40 mm diameter pipe
44
-
-
Providing, Fixing UPVC floor drain including all fitting and accessories fixed in cement
mortar complete in all respect. 110 mm OD x 63 mm OD
29
-
-
Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal
dia with 25 mm waste hole
73
-
-
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making
and finishing the outlet complete.
29
-
-
Providing, fixing and testing of uPVC SWR inlet fittings with two or three saddle inlets of 40, 50 or 75 mm size, fabricated from 110 mm outer dia uPVC pipes and fixed to
uPVC traps with solvent cement joint complete in all respect.
71
-
-
Providing & fixing uPVC clean out plug with suitable opening with threaded uPVC
socket fixed to uPVC pipe joints as required complete in all respects.
-
-
-
110 mm dia
48
-
-
160 mm dia
39
-
-
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm
diameter and weighting not less than 440 grams.
9
-
-
WATER SUPPLY INSTALLATIONS
-
-
-
Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Terrace
and Riser.
-
-
-
PN - 16 Pipe, 20mm OD (SDR-7.4)
65
-
-
PN - 16 Pipe, 25mm OD (SDR-7.4)
40
-
-
PN - 16 Pipe, 32mm OD (SDR-7.4)
145
-
-
PN - 16 Pipe, 40mm OD (SDR-7.4)
160
-
-
PN - 10 Pipe, 50mm OD (SDR-11)
110
-
-
PN - 10 Pipe, 63 mm OD (SDR-11)
45
-
-
PN - 10 Pipe, 75 mm OD (SDR-11)
10
-
-
PN - 10 Pipe, 90 mm OD (SDR-11)
1
-
-
PN - 10 Pipe, 110 mm OD (SDR-11)
5
-
-
Providing and fixing PPR Unions
-
-
-
PPR Union 20 mm
9
-
-
PPR Union 25 mm
9
-
-
PPR Union 32 mm
7
-
-
PPR Union 40 mm
11
-
-
PPR Union 50 mm
11
-
-
PPR Union 63 mm
6
-
-
PPR Union 75mm
1
-
-
Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per
specification and direction of E/l
-
-
-
(a) 15 mm dia wt not less than 300 gms
19
-
-
(a) 20mm dia wt not less than 400 gms
19
-
-
(a) 25 mm dia wt not less than 500 gms
21
-
-
(a) 32 mm dia wt not less than 700 gms
13
-
-
(a) 40 mm dia wt not less than 1kg
7
-
-
(a) 50 mm dia wt not less than 1.5kg
1
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of
Engineer in Charge.
-
-
-
Concealed work, including cutting chases and making good the walls etc.
-
-
-
15 mm nominal outer dia Pipes
406
-
-
20 mm nominal outer dia Pipes
245
-
-
25 mm nominal outer dia Pipes
167
-
-
32 mm nominal outer dia Pipes
45
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per
direction of Engineer in Charge.
-
-
-
Internal work - Exposed on Wall
-
-
-
15 mm nominal outer dia Pipes
65
-
-
20 mm nominal outer dia Pipes
95
-
-
25 mm nominal outer dia Pipes
47
-
-
32 mm nominal outer dia Pipes
44
-
-
40 mm nominal outer dia Pipes
29
-
-
50 mm nominal outer dia Pipes
7
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base
support for tank.
49000
-
-
Butterfly Valves :: - Providing, fixing, testing & commissioning of wafer type cast iron butterfly valves conforming to BS 5155 & IS 13095 tested to 15 Kg/Sq.cm pressure for maximum working pressure of 10 bar (PN 10) including all fitting and accessories
(Drain, water meter for OH Tank/Riser).
-
-
-
50 mm dia
5
-
-
65 mm dia
5
-
-
80 mm dia
1
-
-
100 mm dia
1
-
-
Providing and fixing insulation with thermaflex elastomeric nitrile rubber sheets complete with plastering of 20 mm thick insulation with thermaflex elastomeric nitrile rubber sheets for hot water & cold water pipes exposed and chased to sun complete
with plastering.
-
-
-
15mm (9 mm thickness)
40
-
-
20mm (9 mm thickness)
20
-
-
FIRE FIGHTING WORKS
-
-
-
PUMPS
-
-
-
1.NOC from fire authority shall be in the scope of Contractor . Only fee paid to the fire authority shall be reimbursed against the submission of the receipt and nothing shall
be paid extra.
-
-
-
2. All the Fire Fighting works shall be done in compliance of Fire Fighting authority
requirement.
-
-
-
Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65 % of rated head. The shut off head shall not exceed 120% of rated
head.
-
-
-
Supplying, installation, testing and commissioning of electric driven terrace pump
suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump).
-
-
-
Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze
impeller with stainless steel shaft, mechanical confirming to IS : 1520.
-
-
-
Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure,
horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.
-
-
-
M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as
required.
-
-
-
Suitable cement concrete foundation duly plastered and with anti vibration pads.
-
-
-
900 lpm at 35 m Head
1
-
-
CONTROL PANELS
-
-
-
Supplying,Installation,testing & commissioning of dust & vermin proof double door with canopy type taperd roof wall / floor mounted compartmentlised feeder piller type cubical control Panel for fire fighting terrace pump of front area not less than 1.0 Sqmtr. and depth not less than 300 mm, made out of 2mm thick CRCA sheet with 100 Amp. 4 strip aluminium bus bars with front openable door & locking arrangement, interconnection, control wiring, intrigation with pressure switch i/c suppying & fixing
following switchgears & control gears/starters etc. as required.
-
-
-
Incomming
-
-
-
100 Amps. 16ka breaking capacity 4 pole MCCB-1 Nos.
-
-
-
Voltmeter (0-500 Volt) with selector switch.-1 Nos.
-
-
-
Ammeter (0-100 Amps.) with selector switch -1 Nos.
-
-
-
Set of 3 phase indication lamp-1 Set
-
-
-
100 Amps. 4 strip insulated bus bars-1 Nos.
-
-
-
Outgoing
-
-
-
63 Amps. 10ka breaking capacity 3 pole MCCB--2 Nos.
-
-
-
Ammeter (0-60 Amps.) with selector switch-2 Nos.
-
-
-
Suitable HP fully automatic Star/Delta Starter with over load protection, current sensing type single phase preventor complete with all accessories and internal wiring required for automatic operation.- 2 Set
-
-
-
Selector switch for local/remote, auto/manual/off operation ON/OFF indication etc.- 1 Set
1
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. It should be complete as per specifications & directions of Engineer-in-charge.
-
-
-
4 x 25 sqmm ( 28 mm )
2
-
-
3.5 x 50 sqmm ( 35 mm )
4
-
-
3 X 10 sq. mm (22mm)
8
-
-
Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.150 mm width x 50mm depth x 1.6 mm
thickness.
20
-
-
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
4
-
-
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re- filling etc. as required.
20
-
-
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
40
-
-
Supplying & laying one number XLPE insulated PVC sheathed Aluminium Conductor armoured UG cable of 1.1 KV grade Conforming to IS 7098/1988 with upto date ammendment of following size in the existing RCC/HUME/ METAL /GI /CI
/Stoneware/DWC pipe/ masonary Open Duct/ cable tray/ open in air etc. as requred.
-
-
-
4 core, 25 sq.mm. Aluminium Armoured
50
-
-
3.5 core, 50 sq.mm. Aluminium Armoured
50
-
-
3 core, 10 sq.mm. Aluminium Armoured
20
-
-
Supply and fixing in position 1 m wide Insulation mat made of elastomeric polymers Material (Class -A) of 415V grade as per IS 15642-2006 . Thickness of insulation mat shall be not less than 2 mm to withstand 1.1 KV dielectric strength AS PER IS 15652 : 2006. It should be complete as per specifications & directions of Engineer-in-
charge.
5
-
-
PIPES & ACCESSORIES
-
-
-
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (PDowncomer/Floor)
-
-
-
25 mm dia
10
-
-
100 mm dia
96
-
-
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Gunmetal
6
-
-
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as required :100 mm dia
3
-
-
Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete
as required.
2
-
-
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers
etc.as required : 80 mm dia
1
-
-
Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes
with stainless steel flange.100 mm dia
1
-
-
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as
required :Gun Metal
12
-
-
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.40 m
5
-
-
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous
connection to interconnect hose pipe coupling as required :Gun metal
4
-
-
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way-100 mm dia M.S. Pipe.
1
-
-
Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as
required.
1
-
-
Providing & fixing of pressure switch in M.S. pipe line including connection etc. As required.
1
-
-
Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required
5
-
-
Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.
5
-
-
Providing & Fixing of MS door made up of 16 gauge MS Sheet capable of accommodating fire hose reel, landing valve, hose pipes, fittings, 1 No. CO2 & 1 No. Dry podwer type portable fire extinguishers & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with one coat of primer & two coat of finished stove enamelled post office red colour paint & "FIRE HOSE" written on front.
(Approx. size of door: 2100 mm HEIGHT, WIDTH OF DOOR AS PER SHAFT SIZE )
4
-
-
Providing, Fixing, testing and commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 11 Kg/cm2 and test pressure 16 Kg/cm2 to provide relief from stresses at pipe flanges.80 mm dia
1
-
-
Supply, fixing, testing and commissioning of screwed type brass/bronze lever operated ball valve of full flow with stainless steel ball (AISI 304 & spindle AISI 410) with setting & gland of superior quality having minimum working pressure of 16 kg/sqcm.25 mm Dia
4
-
-
Providing, storing, handling, shifting, installation, testing and commissioning of halon free portable fire Extinguishers as described below: Concealed work, including cutting chases and making good the walls etc.
-
-
-
Supply & Fixing of 6 Kg ABC MAP-50% Powder based Fire Extinguisher, Applicable Fire Class A, B & C, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), IS 15683:2018 Marked. Location : Open General Area, Inside FHC,
6
-
-
Providing and Fixing of CO2 Portable 4.5 Kg Fire extinguisher, Carbon-Dioxide type Flat base Horn Including Valve, High Pressure Rubber Wire Braided Discharge Hose of not less than 10 mm dia. & complete in all respects including initial fill with CO2 Gas confirming to IS:15222. and IS 15683:2018 Marked. Location : Inside Electrical Room, Pump Room,
5
-
-
Providing and Fixing of Portable 4kg Clean Agent HFC-236fa Fire Extinguisher, Gas UL Listed under EPA SNAP, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), Suitable for Class A,B and C & Electrically Started Fires, Conforming to IS 15683:2018 Marked.
Location : General Office Area, Inside of Critical Rooms i.e. Server Room, UPS Near Rooms, Fire Control Room etc.
2
-
-
SIGNAGE WORK
-
-
-
Laser Cut Acrylic Letters with Stain less Steel sides along with Korean Led Lights, Letters will be directly fixed over the Main Facade. 20 Feet by 3 Feet
60
-
-
Laser Cut Acrylic Letters with Stain less Steel sides along with Korean Led Lights,
Letters will be directly fixed over the Main Facade. 9 Feet by 2 Feet
18
-
-
Laser Cut Acrylic Letters with Stain less Steel sides along with Korean Led Lights,
Letters will be directly fixed over the Main Facade. 4 Feet by 3 Feet
12
-
-
Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter Double Side as
required.4 Feet by 2 Feet
288
-
-
Laser Cut 5 mm Acrylic Letters with Pasted over 5 mm Acrylic Sheet with 6 studs.4
Feet by 3 Feet
12
-
-
Laser Cut 5 mm Acrylic Signage with Plotter Cut Vinyl letters pasted above & Desired
color vinyl pasted on Back.4 Inch18 Inch by
52
-
-
Laser Cut 5 mm Acrylic Signage with Plotter Cut Vinyl letters pasted above & Desired
color vinyl pasted on Back
17
-
-
Aluminum Flat Plain Profile with Sliding Acrylic 3 mm for changeable doctors name
(Min. 3 Doctors Name Plate).12 Inch by 4 Inch
14
-
-
Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter Double Side as
required
8
-
-
Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter Double Side as
required.4 Feet by 2 Feet
24
-
-
Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter as required.2 Feet
by 4 Feet
16
-
-
Laser Cut 5 mm Acrylic in desired color with Plotter Cut Vinyl Letter as required.1 Feet
by 2 Feet
4
-
-
Laser Cut 5 mm Acrylic Signage with Plotter Cut Vinyl letters pasted above & Desired
color vinyl pasted on Back.4 Inch18 Inch by
2
-
-
3 mm Acrylic with Desired Color with Plotter Cut Vinyl Letters,6 Inch by 3 Inch
216
-
-
5 mm Acrylic with Desired Color with Plotter Cut Vinyl Letters,2 Feet by 1 Feet
8
-
-
Backlit Acrylic Box Lit with Korean Led ,2 Feet by 1 Feet
2
-
-
MGPS WORKS-
-
-
-
Oxygen System
-
-
-
SITC 4 + 4 size manifold extendable type complete with middle frame with chain for
individual cylinder (bulk cylinder D-type) along with Non-Return Valves for every cylinder and copper tail pipes as per Technical Specifications enclosed.
1
-
-
SITC Semi Automatic Control Panel for Oxygen with inlet for Liquid Oxygen Tank, as
per Technical Specifications enclosed
1
-
-
SITC 1 + 1 Cylinders Emergency Oxygen Manifold with two stage High flow rate
regulator with NRV for every cylinder and copper tail pipes as per Technical Specifications enclosed
1
-
-
SITC Terminal Units (Gas Outlets) with probes/Adaptors ,CE certified , as per
Technical Specifications enclosed.
50
-
-
SITC Oxygen Flowmeter with Humidifier Bottle as per Technical Specification
enclosed
50
-
-
SITC Oxygen H.P Antiastic rubber tube
10
-
-
SITC Compressed Air System
-
-
-
SITC Compressed Air System including Duplex 36.66 cfm , 2 HP Motor, air cooled, oil free compressors and Air Drier, After Cooler, Moisture Saprater and 1# Air Receiver &
Filteration system as per Technical Specification enclosed,
1
-
-
SITC Terminal Units (Gas Outlets) with probes/Adaptors CE Marked, as per Technical Specifications enclosed. For C.Air ( 4 bar)
16
-
-
SITC H.P Tubing Flexible having antistatic Core as per ISO with Proper colour coded
as per Technical Specification enclosed.
10
-
-
Vacuum System
-
-
-
SITC Duplex V X 15 Vacuum Pumps of Ingersoll with Motor each with receiver vessel,
with bacteria filter capacity as per Technical Specification enclosed.
1
-
-
SITC Terminal Units (Gas Outlets) with probes/Adaptors CE Marked, as per Technical
Specifications enclosed.
50
-
-
SITC Ward Vacuum Unit with Regulator, Collection Jar of 600 ml with bracket as per
Technical Specification enclosed,
50
-
-
SITC Theatre Suction Unit, Trolley mounted with 2 nos. 2000ml Collection jars, jar
selector unit and Suction Controller as per Technical Specification enclosed
1
-
-
SITC H.P Tubing Flexible having antistatic Core as per ISO with Proper colour coded
as per Technical Specification enclosed.
10
-
-
SITC Combined Electrical Control Panel for Compressed Air System and Vaccum
System as per Technical Specification enclosed.
1
-
-
SITC Copper Pipes used will be solid drawn, seamless, deoxidized, non arsenical, half hard, tempered and degreased, manufactured as per EN 1057 part I, Table-X of 1971 and chemical composition as per BS-6017 of 1981, Table 2, Cu-DHP.
-
-
-
42mm OD X 1.2mm thk
50
-
-
28mm OD X 1 mm thk
170
-
-
22mm OD X 0.8 mm thk
440
-
-
15mm OD X 0.7 mm thk
530
-
-
12mm OD X 0.7 mm thk
180
-
-
SITC Valves Boxes with Pressure Gauges as per Technical Specifications.
-
-
-
2 Gas Services ( O2, Vac, Air 4)
6
-
-
3 Gas Services ( O2, Vac, Air 4)
1
-
-
SITC Area Alarm as per Technical Specifications enclosed
-
-
-
2 Gas Services ( O2, Vac, Air 4)
5
-
-
3 Gas Services ( O2, Vac, Air 4)
3
-
-
SITC Isolation Valves as per Technical Specifications enclosed
-
-
-
42mm OD
4
-
-
28mm OD
7
-
-
22mm OD
8
-
-
15mm OD
6
-
-
Bed Head Panels
-
-
-
SITC Horizontal Bed Head Panel (Al Extruded) 4 ft. Long Provision for Gas Outlet, Electrical Switch & Socket, Nurse Call, etc
38
-
-
HVAC- WORK
-
-
-
Air Cooled Inverter Ductable Unit
-
-
-
Supplying, installing, testing and commissioning of Air Cooled Invertor Split type Ducted Air conditioners suitable for R410A or eco-friendly refrigerant with evaporating unit comprising of cooling coil, blower with motor in Metallic (Steel) casing and condensing unit comprising hermetically sealed scroll compressor, condenser coil, and propeller fan. Unit shall be complete with controls, interconnecting copper refrigerant piping with insulation, Expension kit to connect with DX AHU, and electrical cabling etc. between evaporative and condensing unit, refrigerant gas and oil and complete as per specifications. The unit shall be suitable for operating on 240 volt, 1 phase, 50 Hz AC supply with five star energy rating. The units shall be suitable for chorded remote operation. The refrigerant piping & cabling shall run in PVC sleeve Steel supporting structure for outdoor units suitable for wall mounting / floor mounting.
-
-
-
Providing, fixing and testing of copper refrigerant piping of appropriate sizes duly insulated with nitrile rubber insulation of 19 mm thickness. The pipes plus nitrile rubber insulation and cable are to be covered with PVC flexible conduits for protection.
-
-
-
Note: Providing and fixing of Powder coated M.S. angle iron frame work/Masonary Pedastal with required anti-vibration mounting for outdoor unit is also included in the above scope. Contractor to submit design/Scheme for Iron frame and obtain approval
of engineer/employer before proceeding purchase & installation.
-
-
-
Nitrogen pressure testing for refrigerant pipe leakages & flushing during installation & after commissioning between IDU & ODU with flare nuts. Refrigerant gas & oil
charging as per OEM standard.
-
-
-
Necessary corrosive treatment of copper coil of the ODU with Aluminium hydroxide, 25 microns thickness or equivalent coating as per manufacturer standard to protect from corrosion, sulfur and other chemical contaminants present in the air. The coating should be done in the presence of OEM represantative. The coating shall be carried-
out by the authorized applicator of coating manufacturer.
-
-
-
11.0 TR Ductable Split Unit -Only Condensing
1
-
-
DIRECT EXPENSION FLOOR MOUNTED AHU (DX FMAHU)
-
-
-
(For OT With 10 ACH/Hr)
-
-
-
Supply, installation, testing and commissioning of factory fabricated Double Skinned DX Type Air- handling unit floor mounted fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm polished SS sheet inside with backward curved fan in supply and forward curved in exhaust with fan section and fan motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 8 row cooling made of Aluminium finned Copper tube, Copper header with coil section, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% in both the supply & exhaust side of AHU, fine filter section with filters of non woven synthetic media of 5 micron particle size in supply after fan, (Hepa filters shall be at terminals along with laminar flow plenum & not to be included in the cost), mixing chamber, polished stainless steel drain pan made out of 22 G sheet duly insulated complete with motor, belt drive package, guard etc. without face and bypass dampers. The AHU panels shall be insulated with 48mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. These AHUs shall have air inlet / outlet connection made of aluminium 20 G & all fixing arrangement / blank off shall be of SS The complete AHU shall conform to standard specication with starter Panel. The face velocity across cooling / heating coil shall be limited to 152 MPM
maxm. The capacity of Air-handlers shall be as follows:
-
-
-
AHU Units Mounted on MS Frame/Masonary Pedastal with required anti-vibration
mounting.
-
-
-
3000 CFM Supply Air, 8 Row CC, 125 mm St. Pr., For Supply Fan, Supply Fan, 1000 CFM Ex. Air Blower, 40 mm St. Pr. for Exhaust fan with other accessories as specified)
1
-
-
DRAIN PIPING
-
-
-
Supply,installation,testing and commissioning of UPVC drain piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell expanded polythene. 40 mm ID
10
-
-
SHEET METAL DUCT
-
-
-
Supply. Installation, testing and commissioning of factory fabricated G.I. Sheet metal ducts with flanges, inbuilt sealant, gasket, supports, vanes, dampers, links, levers and quadrants etc. as per specifications and drawings. Duct shall be furnish at site in "L" shape or box shape from factory. The rates shall include all materials of the duct and labour for suspension and supporting arrangement for plenums, ducts, complete with fire retardant flexible connection as required and as per specifications.
-
-
-
0.63 MM (24 Gauge )
45
-
-
0.80 MM (22 Gauge )
35
-
-
1.00 MM (20 Gauge )
1
-
-
1.25 MM (18 Gauge) Plenum
5
-
-
Duct Insulation
-
-
-
Supply. Installation, testing and commissioning of insulation on the surface of the duct with duly laminated aluminum foil of mat finish closed cell nitrile rubber (Class 'O' ) with suitable adhesive, as per specifications and drawings. The Joints shall be sealed with 50mm wide and 3 mm thick self adhesive nitrile rubber tape Insulation. The rates shall include all materials of the insulation and labour works with adhesive, complete as
required and specifications.
-
-
-
19 mm
86
-
-
25 mm
1
-
-
Duct Acoustic Lining
-
-
-
Supply and fixing of acoustic lining of supply air duct and plenum with thick Engineered Nitrile Rubber open cell foam having a Noise Reduction Coefficient of
0.55 with Density 140 - 180 Kg/m3 passing Class 1 Fire Performance test as per BS 476 Part 7, Air Erosion test for 10,000 fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection. The material should pass Fungi Resistance Test as per DIN EN ISO 846 Method A and Bacterial Resistance Test as per DIN EN ISO 846 Method C; to be applied using manufacturer's recommended Rubber based
-
-
-
20 mm
86
-
-
25 mm
1
-
-
Grills and Dampers
-
-
-
G.I construction Duct Dampers / Volume Control Damper
-
-
-
Supply. Installation, testing and commissioning of G.I construction Duct/ Volume control Dampers for Controlling the Airflow in Ducts with neoprene rubber
gaskets,nuts, Bolts, Screws Linkages, Flanges etc. as per specification.
1.5
-
-
Grilles without Dampers
-
-
-
Supply. Installation, testing and commissioning of powder coated extruded aluminum sections grills as per specification.
1.5
-
-
Grilles with Dampers
-
-
-
Supply. Installation, testing and commissioning of powder coated extruded aluminum section grills with dampers for supply air terminal for air-conditioning as per specification.
2
-
-
Flexible Duct
-
-
-
Supply. Installation, testing and commissioning of thermal flexible aluminum duct of following sizes duly supported at regular interval as per site requirement &
spefications. 200 mm
10
-
-
Linear Grille
-
-
-
Supply. Installation, testing and commissioning of powder coated extruded aluminum
Linear Grille. 200 mm
10
-
-
Exhaust/Fresh Air Louvers
-
-
-
Supply. Installation, testing and commissioning of exhaust air/fresh air louvers of powder coated extruded aluminum construction with bird screen, minimum 80 mm
deep.
0.5
-
-
Under Deck Insulation of Exposed Roof
-
-
-
Providing and Fixing Underdeck Insulation with 50 mm thick with closed cell Nitrile Rubber with prelaminated Aluminum foil on one side having a low stable k value of
0.035 k.cal/hr.m at 10.C and minimum density of 40-55 ± 3 kg/cum.The R-value should be as per ECBC Code. 50mm
40
-
-
ISOLATOR FOR OUTDOOR UNIT
-
-
-
Supply, Installation, Testing & Commissioning of following Switchgears as an Isolator in IP-65 rated in power coated 16 SWG sheet steel enclosure of suitable for VRV
Outdoor Unit. 63A 4P MCCB(16 KA)
1
-
-
POWER CABLING
-
-
-
Supply, laying, testing and commissioning of power and control cabling as per
specification given in the tender.
-
-
-
A) Power cabling (XLPE insulated Aluminum / Copper conductor as given below armoured / unarmoured cables of 1.1 KV Grade) including cable end
termination with brass compression glands & lugs etc. as per specification.
-
-
-
Note:- Power cable with earthing shall be made available near indoor / outdoor units.
Only termination into HVAC equipment's (Indoor & Outdoor) shall be done by HVAC Contractor.
-
-
-
4C x 16 Sq. mm Copper Conductor (Armoured) For VRF Unit
10
-
-
4C x 10 Sq. mm Copper Conductor (Armoured) For AHU/Vent
10
-
-
4C x 6 Sq. mm Copper Conductor (Armoured) For AHU/Vent
10
-
-
4C x 4 Sq. mm Copper Conductor (Armoured) For AHU/Vent
10
-
-
FURNITURE WORK-
-
-
-
NICU BED
-
-
-
SITC Plastic/ABS Head NICU BED Size of 830 L x 600 W x 600 H Pre trated and Epoxy Powder Coated,Manually Operated four function bed featuring,Trendelenburg's reverse with Hi-Lo postion Frame & Plateform should be made of CRCA steel with IV Rod and Split Rolling Function,Castor should be 125mm
2
-
-
FOWLERS BED
-
-
-
SITC Plastic/ABS Bed Head Panels Size of 2030 L x 900 W x 600 H Pre trated and Epoxy Powder Coated,Manually Crank Operated with Hi-Lo postion Frame &
Plateform should be made of CRCA steel with100 mm Swivel castor
30
-
-
LABOUR TABLE
-
-
-
SITC Size of 2030 L x 900 W x 600 H Pre trated and Epoxy Powder Coated,CRCA Steel Tube Frame,SS Three section top,Leg section should be slides completely under the trunk section.Labour table should be Adjustable back on rachect ,padded Lithotomic cructhes mattress,hand grips on either side.
3
-
-
BED SIDE LOCKER
-
-
-
SITC Single Storgage box,Size of 400 L x 400 Wx 800 mm H epoxy powder coated
,Frame should be CRCA Sheet/Tube closed on threeside with SS top,having two PVC shpe and two 50 mm castors.
30
-
-
OVER BED TABLE
-
-
-
SITC Frame made of CRCA steel tube with epoxy powder coated,laminated wooden
board with adjustable gear.Dimension of top : 750 L x 400 w mm ,Table stand on 50 mm castors.
30
-
-
SS STOOL
-
-
-
SITC Pre treted epoxy powder coated SS revolving stool made of CRCA steel tube with four leg height adjustable upto 675mm,reinforced with steel frame.Foot rest ring
on PVC shoes.
30
-
-
IV STAND
-
-
-
SITC Made of CRCA tube ,pre tyreted epoxy powder coatedwith plastic 5b progned base.SS rod with double hook with height adjustable knob upto 2025mm approx on
50mm castors.
30
-
-
AUDIO & VIDEO WORK
-
-
-
SITC 42" LED Display
2
-
-
SITC Display Manager with Splitter
1
-
-
SITC Application - (Customized)
1
-
-
SITC HDMI Extender
2
-
-
SITC HDMI Cable Set
4
-
-
Installation & Configuration
1
-
-
MAJOR OT WORK
-
-
-
Laminar Air Flow System
-
-
-
Providing & installation of Planair Ceiling System. Constrcuted out of 2 mm thick extruded aluminium sheets of size 2,400 x 2,400 mm having 2 nos. of Hepa Filters. The Hepa Filters having dust spot efficiency of 99.99%, 0.3 microns. Provided with Perforated Aluminium Air Diffuser for the plainair ceiling to give a Laminar Flow of filtered Air. Air Supply System and ducting work including return air duct to be done by
Air Conditioning Contractor.
1
-
-
Manual Sliding Door System
-
-
-
Supply, installation, testing & commissioning of sliding type Hermatically Manual OT door having high density particle board cores, high pressure laminate face on both sides, viewing window 300 x 300mm.
Size: 1500 x 2100 mm (W x H). Manual Door (1500 mm x 2100 mm)(PES)
1
-
-
Surgeon Control Panel
-
-
-
SITC OF Surgeon Control Panel membrane type, mounted
flush in the theatre wall, comprising of the following: 1 No. Day Time Clock
1 No. Elapse Time Clock
1 No. Medical Gas status/ alarm 1 No. HEPA status/ alarm
1 set indicator only fortemperature and humidity display
1
-
-
Storage Unit
-
-
-
Supply & instalaltion of Storage Unit size 1666 x 865 x350mm having two shelves, made 1.5 mm thick EGP with 120 microns. With Antifungal and Antibacterial surface coating. Having 5 mm thick acrylic sheet & mounted flush with the theater wall.
1
-
-
Single Arm Pendant
-
-
-
Providing & fixing of double arm multi moveable surgeons pendant as per technical specs attached.
1
-
-
OT Light(Wilson)
-
-
-
OT Light with Provision of Camer
Operating Room Surgical Lighting System provide an ideal combination of brightness, maneuverability, and shadow resolution without sacrificing colour accuracy through a consistent LED technology.
Such Lighting System have the following technical specifications
• Number of Light heads : Two per suspension
• Color Temperature range: 3500K to 4500K
• Field Size Diameter : Small field D50: 18cm / Big field D10: 26cm
• Working Range : 750 to 1100mm (+/- 10%).
• Illumination Level :Focusmatic technology, we should provide 160 000 lux at the central illumination spot (Ec) at small field AND big field. There not be drastic loss of illumination level at the central illumination spot (Ec) when shifting to big field Controls
: On/off + Endo Mode button & 3 optical sensors to control in a touchless and sterile way the following parameters: light intensity (6 steps from 50 000 Lux to 160 000Lux),
colour temperature (3500 K, 4000 K & 4500 K) &
1
-
-
OT Table(Wilson)
-
-
-
Universal General Purpose Operating table having five section top,perineal cut,detechuing leg section provided with mattress,Dimesnsion should be 1830 x 485 x 767 mm,Trendelburg's position 30vdeg reverse Trendelburg's position 30vdeg
,Lateral tilting position 20 deg either side and lifting position should be 225mm,flex position 90 degree,reflex position 220 degree& Head movement 20 degree up and 90
degree down.
1
-
-
MINOR OT WORK-
-
-
-
Antibacterial / Antifungal Paint
-
-
-
SITC Providing and applying Antibacterial Paint: The internal surfaces of the room.walls will be sprayed with water based liquid plastic, wall glaze or equivalent anti- bacterial paint, approved by the architect to a minimum dry film thickness of 300 microns. The plastic coating will overlap the floor covering ceiling system and doorframes by 25mm to provide a continuous sealed surface. The plastic coating will
be non- reflective and the Colour will be submitted to the architect for approval.
50
-
-
Dimmable Peripheral Lights
-
-
-
SITC Peripheral Lights non hygroscopic peripheral lights peripheral lights for clean room application, low power consumption with dimmer control (suitable for clean room application). The luminaries to be provided in such a way to achieve light intensity of 350 Lux at 1m from floor. Dimmable Peripheral Lights will be CE certified and in
compliance under Class 1 Medical devices
6
-
-
Storage Unit
-
-
-
SITC Storage Unit of size (1050 x 2100 x 350) .The storage unit cabinet will be finsihed in Powder coat .The unit will be divided into 2 equal parts and each part will have individual glass doors with locking system .Each part will have racks to keep surgical medicines etc.Storage Unit will be CE certified and in compliance under
Class 1 Medical devices
1
-
-
Single Arm Moveable Pendant - CE Marked
-
-
-
SITC Single Arm Pendant will have 1000mm arms with Horizontal movement having load carrying capacity of 100kgs. The Single arm will be rotated upto 330degree to 340 degree . Pendant will have 1 arms with two shelves as per points : 1) 5/15 Amp Electrical sockets without switches - 8 to 10 nos., 2) shelfs with side rails - 2 nos. 3)
Provision to fix 3 Nos Gas Outlets.
1
-
-
X-Ray View Screen
-
-
-
SITC X-ray view box:- Twin Plate X-Ray viewing screen with flicker free dimming light range from 15 to 100% with complete accessories as required to
view the X-ray film.
1
-
-
OT Table
-
-
-
SITC Universal General Purpose Operating table having five section top,perineal cut,detechuing leg section provided with mattress,Dimesnsion should be 1830 x 485 x 767 mm,Trendelburg's position 30vdeg reverse Trendelburg's position 30vdeg
,Lateral tilting position 20 deg either side and lifting position should be 225mm,flex
position 90 degree,reflex position 220 degree& Head movement 20 degree up and 90 degree down.
1
-
-
Manual Sliding Door System
-
-
-
Supply, installation, testing & commissioning of sliding type Hermatically Manual OT door having high density particle board cores, high pressure laminate face on both sides, viewing window 300 x 300mm.
Size: 1500 x 2100 mm (W x H).
1
-
-
INTERNAL ELECTRICAL WORK
-
-
-
Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required.
-
-
-
Group A
134
-
-
Group C
520
-
-
Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way modular switch, modular
plate, suitable GI box etc as required.
22
-
-
Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC
insulated copper conductor single core cable for loop earthing as required.
3355
-
-
Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 2 No 4 sq. mm FR PVC
insulated copper conductor single core cable for loop earthing as required.
570
-
-
Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit
as required
-
-
-
CIRCUIT / SUBMAIN WIRING
-
-
-
2x1.5 sq mm + 1x1.5 sq mm earth wire
2505
-
-
2x2.5 sq mm + 1x2.5 sq mm earth wire
3180
-
-
2x6 sq mm + 1x6 sq mm earth wire.
55
-
-
2x10 sq mm + 1x6 sq mm earth wire.
70
-
-
2x16 sq mm + 1x6 sq mm earth wire.
60
-
-
4x2.5 sq mm + 2x2.5 sq mm earth wire
275
-
-
4x6 sq mm + 2x6 sq mm earth wire.
130
-
-
4x10 sq mm + 2x6 sq mm earth wire.
320
-
-
4x16 sq mm + 2x6 sq mm earth wire.
450
-
-
Supplying and drawing 2 pair 0.5 mm dia FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair
370
-
-
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
510
-
-
Supplying and fixing of following sizes of PVC conduit along with the accessories in
surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
-
-
-
20mm dia
815
-
-
25mm dia
3590
-
-
32mm dia
165
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate &
switch box including connections but excluding modular plate etc. as required.
-
-
-
5/6 amps one way switch
511
-
-
15/16 amp one way switch
226
-
-
5/6 amp 3 pin socket outlet
511
-
-
5/16 amp 6 pin socket outlet
226
-
-
Telephone Socket Outlet
15
-
-
TV anteena Socket Outlet
18
-
-
Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
107
-
-
Supplying and fixing modular blanking plate on the existing modular plate & switch
box excluding modular plate as required.
118
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover
plate for modular switches in recess etc as required.
-
-
-
1 or 2 Module (78mm x 78mm x 45mm) - For Telephone & TV outlet.
33
-
-
4/5 Module (78mm x140mm x 50mm)
537
-
-
6 Module (78mmX205mmx50mm)
200
-
-
8/9 Module (78mmX230mmx60mm)
60
-
-
12 Module (135mmX205mmx60mm)
20
-
-
Supplying and fixing 2 pin 5 Amp Ceiling rose on the existing junction box/ wooden
block including connection etc as required.
107
-
-
Supplying and fixing brass batten/ angle holder including connection etc. as required.
15
-
-
Supplying and fixing Ding dong sound call bell single phase, 230 volts, complete as
required.
7
-
-
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor,
single core cable, etc. as required.
87
-
-
Installation of exhaust fan up 450 mm sweep in the existing opening including making the hole to suit the size of above the fan, making good the damage,
connection, testing, commissioning etc. as required.
21
-
-
Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
21
-
-
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20mm dia
360
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including
earthing etc. as required. (But without MCB/RCCB/Isolator)
-
-
-
8 Way Double Door
4
-
-
12 Way Double Door
9
-
-
Supplying and fixing following ways, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted
including earthing etc. as required. (But without MCB/RCCB/Isolator)
-
-
-
6 Way (4+18), Double Door Horizontal Type
2
-
-
8 Way (4+24), Double Door Horizontal Type
4
-
-
Supplying and fixing following ways surface / recess mounting Vertical type 415 Volts TPN MCB distribution board, of sheet steel dust protected duly power painted inclusive of 200 Amps tinned copper bus bar common, neutral link, earth bar, din bar, for mounting MCB's (But without MCB's and incomer) as required. ( Note:- Vertical Type MCB TP DB is normally used where 3phase outlets are required.
-
-
-
8 Way (4+18), Double Door Vertical Type
11
-
-
12 Way (4+16), Double Door Vertical Type
8
-
-
Supplying and fixing 6 Amp to 32 Amp rating 240 volts, 10 KA "C" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc.,as required.
-
-
-
6 / 32 Amp Single Pole
606
-
-
40 Amp DP
4
-
-
50/63 Amp DP
7
-
-
6/32 Amp TPN
4
-
-
40 Amp TPN
6
-
-
50/63 Amp TPN
15
-
-
Supplying and fixing Single pole blanking plate in the existing MCB DB complete etc.
as required.
72
-
-
Supplying and fixing of following rating double pole ( Single pole & neutral), 240 volts, resudual current circuit breaker (RCCB), having a sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc as
required.
-
-
-
16/25 Amps
12
-
-
40 Amps
22
-
-
63 Amps
52
-
-
Providing and fixing M.V. danger Notice plate of 200mm x 150 mm of made of mild
steel, at least 2 mm thick and vitreous enamelded white on both side and with inscription in single red colour in front side as requird
6
-
-
Providing and fixing H.T. danger Notice plate of 250mm x 200 mm of made of mild steel, at least 2 mm thick and vitreous enamelded white on both side and with
inscription in single red colour in front side as requird
2
-
-
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and
watering pipe etc. (with charcoal or coke and salt) as required.
31
-
-
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking
arrangement and watering pipe etc. (with charcoal or coke and salt) as required.
7
-
-
Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for
connections etc. as required.
75
-
-
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections
etc. as required
390
-
-
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing
along with existing surface/ recessed conduit/ submain wiring/ cable as required.
190
-
-
Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for
connections etc. as required.
10
-
-
Providing and fixing 50 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required
10
-
-
Providing and fixing of lighting conductor finial made of 25 mm dia 300 mm long, GI tube having single prong at top with 85 mm dia 6mm thick G.I Base plate including
hole etc. as required
8
-
-
Providing and fixing GI Tape 20mmx 3mm thick on parapet or surface of wall for
lighting conductor complete as required. ( for Horizental Run)
250
-
-
Providing and fixing GI Tape 20mmx 3mm thick on parapet or surface of wall for
lighting conductor complete as required. ( for Vertical Run)
80
-
-
Providing and fixing testing Jointing made of 20mmx 3mm thick G.I Strip 125 mm
Long. With 4 nos of G.I bolts. Nuts chuck nuts and spring washers etc. as required
8
-
-
Providing and Laying G.I tape 32mm x 6mm from earth electrode directoly in ground
as required.
80
-
-
Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming
to IS-7098. (Part-I).
-
-
-
3.5 core, 240 sq.mm.
80
-
-
3.5 core, 185 sq.mm.
140
-
-
3.5 core, 150 sq.mm.
420
-
-
3.5 core, 120 sq.mm.
120
-
-
3.5 core, 95 sq.mm.
80
-
-
3.5 core, 70 sq.mm.
60
-
-
3.5 core, 35 sq.mm.
450
-
-
4 core, 16 sq.mm.
75
-
-
2 core, 6 sq.mm.
600
-
-
Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :
-
-
-
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
10
-
-
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and
protective covering etc., complete as required.
-
-
-
120 mm dia (OD-120 mm & ID-103 mm nominal)
10
-
-
200 mm dia (OD-200 mm & ID-175 mm nominal)
10
-
-
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/
recessed Steel/ PVC conduit as required.
-
-
-
1 run of cable
2500
-
-
2 run of cable
600
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning,
protective covering and refilling the trench etc as required.
-
-
-
Upto 35 sq. mm
500
-
-
Above 35 sq. mm and upto 95 sq. mm
10
-
-
Above 95 sq. mm and upto 185 sq. mm
10
-
-
Above 185 sq. mm and upto 400 sq. mm
10
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.
-
-
-
Upto 35 sq. mm
450
-
-
Above 35 sq. mm and upto 95 sq. mm
20
-
-
Above 95 sq. mm and upto 185 sq. mm
240
-
-
Above 185 sq. mm and upto 400 sq. mm
580
-
-
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.
-
-
-
Upto 35 sq. mm (clamped with cable tie)
580
-
-
Above 35 sq. mm and upto 95 sq. mm (clamped with cable tie)
140
-
-
Above 95 sq. mm and upto 185 sq. mm (clamped with cable tie)
300
-
-
Above 185 sq. mm and upto 400 sq. mm (clamped with cable tie)
10
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
-
-
-
2 x 6 sq. mm (19mm)
16
-
-
3½ X 35 sq. mm (32mm)
10
-
-
3½ X 70 sq. mm (38mm)
2
-
-
3½ X 95 sq. mm (45mm)
2
-
-
3½ X 120 sq. mm (50mm)
2
-
-
3½ X 150 sq. mm (50mm)
8
-
-
3½ X 185 sq. mm (57mm)
2
-
-
3½ X 240 sq. mm (62mm)
4
-
-
4 X 16 sq. mm (28mm)
6
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling
with G.I. suspenders including G.I. bolts & nuts, etc. as required.
-
-
-
100 mm wide x 50 mm depth x 1.6 mm thickness.
30
-
-
300 mm wide x 50 mm depth x 1.6 mm thickness.
20
-
-
450 mm wide x 50 mm depth x 2.0 mm thickness.
20
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling
with G.I. suspenders including G.I. bolts & nuts, etc. as required.
-
-
-
100 mm wide x 50 mm depth x 1.6 mm thickness.
5
-
-
300 mm wide x 50 mm depth x 1.6 mm thickness.
5
-
-
450 mm wide x 50 mm depth x 2.0 mm thickness.
2
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling
with G.I. suspenders including G.I. bolts & nuts, etc. as required.
-
-
-
100 mm wide x 50 mm depth x 1.6 mm thickness.
2
-
-
300 mm wide x 50 mm depth x 1.6 mm thickness.
2
-
-
450 mm wide x 50 mm depth x 2.0 mm thickness.
4
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.
-
-
-
100 mm width X 50 mm depth X 1.6 mm thickness
2
-
-
300 mm width X 50 mm depth X 1.6 mm thickness
3
-
-
450 mm width X 50 mm depth X 2.0 mm thickness
2
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling
with G.I. suspenders including G.I. bolts & nuts, etc. as required.
-
-
-
100 mm wide x 50 mm depth x 1.6 mm thickness.
2
-
-
300 mm wide x 50 mm depth x 1.6 mm thickness.
3
-
-
450 mm wide x 50 mm depth x 2.0 mm thickness.
2
-
-
11 KV END TERMINATION:
-
-
-
supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE
aluminium conductor cable of 11 KV grade as required : 3C x 240 Sqmm, 11KV XLPE
2
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning,
protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm
50
-
-
SUPPLY OF LIGHT FIXTURES & FANS
-
-
-
SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all
neccesary accessories as required. Make:- Havells/Philips/Crompton/Wipro.
-
-
-
12W LED Round Down Light (Recess )
55
-
-
15 / 16 W LED Round Down Light (Recess )
140
-
-
18 /20 W LED Round Down Light (Surface)
58
-
-
18 /20 W LED Round Down Light (Recess)
2
-
-
2' x 2' LED Panel Light (Recess)
142
-
-
Bulk Head fitting with 9/10Watt LED.
12
-
-
S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for
230V 50 Hz, Single Phase Supply etc. complete as required.
-
-
-
10/12 W LED Tube Light
27
-
-
20/22 W LED Tube Light
187
-
-
SITC of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts,
50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Usha/Crompton / Havells .
33
-
-
Supply Installation, Testing & Commissioning of following sizes ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard (up to 30cm) with 1.5 sq.mm FR PVC insulated copper wire suitable for 230V 50 Hz, Single phase supply etc. complete as required. Make :- Usha/Crompton / Havells . 1200 mm ( 48") BLDC 5 Star rating 32W Ceiling Fan
111
-
-
S.I.T.C of Following rating LED Street Lighting luminare with pressure die cast housing and toughened glass cover (IP 66 protection ) in existing pole / pipe for supply voltage 100-270 AC 50Hz Luminare shall be confirm to IS :10322 part 5/ section-3 and shall be complete with all nessessary accessories as required. 90/100W LED Street Light
34
-
-
S.I.T.C of Following rating LED Post Top lamp made in die cast aluminium housing
with decorative clear / opel acrylic diffuser on existing pipe including connection with 1.5sq.mm coppwr conductor etc all complete as required. 20/25W LED Post top lamp clear
4
-
-
S.I.T.C of Following rating approved make LED Bpllard Fitting with cylindrical shape and inverted cone shape head of height 600 to 850 mm power input -8/9 watt with die cast aluminium housing opel with PC diffuser, IP-65/54 protection, conferming to IS : 10322 part 5 etc all complete as requird. (Excluding Plinth Charge.)
15
-
-
Supplying & installation of 7 mtr. Height Octagonal Hot Dip galvanized pole (BOP. 7030) with top dia 70 mm bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x12 mm (LxBxT) including suitable size of foundation bolt all complete as required (without Arm).
34
-
-
1m Single Arm Suitable for 70MM Top
34
-
-
Supply and fixing of telephone distribution board (tag blocks) in hinged type MS box duly powder coated complete with bakelite sheet with termination of incoming and outgoing telephone wire etc. complete as required. 10 pair telephone distribution board.
4
-
-
Supply and wiring of telephone tag block with 0.5mm dia annealed tinned copper conductor PVC insulated and PVC sheathed unarmoured telephone cable in existing conduit in concealed/ surface system / existing cable tray
complete as required. 10 pair telephone unarmoured cable.
40
-
-
Supply, erection, testing and commissioning of following sizes of splitter of aluminium die cast body in suitable size of G.I. Box. 4 way
4
-
-
FIRE ALARM SYSTEM (ADDRESSABLE TYPE) AND PA SYSTEM
-
-
-
Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as
-
-
-
Two Loop Panel.
1
-
-
Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.
1
-
-
Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector acclimate type sensetive level (0.524%) OVS/ft. complete with mounting base complete as required.
114
-
-
Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.
2
-
-
Supplying, installation, testing & commissioning of addressable manual call point complete as required.
6
-
-
Supplying, installation, testing & commissioning of addressable fire control module
complete as required.
2
-
-
Supplying, installation, testing & commissioning of addressable horn cum strobe
complete as required. (75 DBA @3 mtr. & 75CD flashing)
6
-
-
Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all
connections etc as required.
50
-
-
Supplying, installation, testing & commissioning of fault isolator complete with base as
required.
12
-
-
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required
2350
-
-
Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.
1
-
-
Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.
1
-
-
Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.
24
-
-
Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.
2
-
-
Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable Single pair, 2-core, 1.5 sqmm
360
-
-
DATA, TELEPHONE SYSTEM INCLUDING ACTIVE COMPONENTS
-
-
-
Supply, Installation, Testing & Commissioning of Cat 6, 24 Port Patch Panel
5
-
-
Supply, Installation, Testing and Comissioning of Cat 6 patch cord 3 feet for rack and
user end termination - 1Mtr
80
-
-
Supply, Installation, Testing and Comissioning of Cat 6 patch cord 7 feet for rack and
user end termination - 2Mtr
28
-
-
Supply, Installation, Testing, Commissioning of Cat 6, Information Outlet (I/O)
including G.I. Box and modular cover plate.
108
-
-
Supply, Installation, Testing and Comissioning of 24U floor mounted Rack with
accessories.
1
-
-
Supply, Installation, Testing & Commissioning of 24 port 10/100/1000Mbps, 4SFP
module, L-2 Switch, POE.
5
-
-
Supply, Installation, Testing & Commissioning of EPABX SYSTEM Configuration as Below:-
Analog Trunk Line 6 Nos.
Digital Line 2 Nos
Analog Extensions 60 Nos.
1
-
-
Supply, Installation, Testing & Commissioning of Digital Phone for Operator Console
1
-
-
Supply, Installation, Testing & Commissioning of Type Analog Phone with speaker
phone, .
28
-
-
Supply, Installation, Testing & Commissioning of 6 Core OM4 Multimode Fiber
Cable as per technical specification.
30
-
-
UPS SYSTEM
-
-
-
Supply, fitting, fixing, testing and installation of 40 KVA, ON Line UPS three phase input and three phase out put power system of in put voltage range 360V/380/V/400V/485V AC , Frequency range 40 HZ to 60 Hz, +/- 10% and out put voltage range 415V +/-1%, AC frequency range, 50Hz, +/-1% poower factor 0,8/3.1, Harmonic distrortion - 2% THD (Linear Load): 5% THD (Non- Liniear Load) along with required Batteries, Battery Stand, UPS Box Battery Lead etc as required.
-
-
-
UPS shall carry design output at 40 deg.
-
-
-
Shall have soft start and hold of for incoming supply.
-
-
-
Invertor capability to supply 150% load for 5 sec.
-
-
-
SNMP card, compatible for BMS connectivity on backnet/MODBUS, Inbuilt Isolation
transforme.
-
-
-
Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of
12 volt cells.
-
-
-
Battery shall be external type with rack and suitable for 30 minute backup on 100%
load.
-
-
-
Suitable size of copper cable between UPS and battery bank shall be provided
-
-
-
UPS shall be compatible for 3 nos unit in parallel operation. (Synchronize). Parallel
operation kit shall be supplied with UPS.
-
-
-
SITC of MS Battery Rack suitable for 40 to 50 UPS Battery Installation.
-
-
-
SITC of 60 nos. 65 AH Flat type Sealed Maitanace Free (SMF) Battery with 24 months replacement warranty. IS:1652:1991. (VAH Required minimum 46800 for 40
KVA UPS (65AH x 60 Nos. x 12V = 46800 VAH)
1
-
-
IP CCTV SYSTEM
-
-
-
Supplying, installation, testing & commissioning of 1080p HD Indoor IP Dome camera with1/3-inch CMOS, Sensor pixels 1920 x 1080, Sensitivity-0.04 lx (color) , Dynamic range 75 dB Wide Dynamic Range (WDR), True day/night, Automatic Electronic Shutter, Video compression H.264 ; M-JPEG, White balance, BLC, H.264 quad- streaming, Motion/tamper/audio detection, Privacy Mask, Lens 3.6 mm lens, 3-axis
adjustment (pan/tilt/ rotation), ONVIF Profile S, CE Certified.
19
-
-
Supplying, installation, testing & commissioning of 5MP 30 fps HD indoor / outdoor IR IP bullet camera with 1/3-inch CMOS, Sensor pixels 2612 (H) x 1980(V), Sensitivity-
0.24 lx (color) 0.04 lx (mono) ,IR range 30 mtrs, Dynamic range 70 db, True day/night, Automatic Electronic Shutter, Video compression H.264 MP ; M-JPEG, White balance, BLC, Analog video output, Lens (zoom / focus) 3.6 mm lens, Two- way, full duplex Audio, Audio compression AAC, G.711, L16 , ONVIF Profile S, CE
Certified.
4
-
-
Supply installation and commission of pann tilt zoom camera with 360 deg pan and
90 deg tilt with 36 X Zoom having maximum resolution of Max. 1920 × 1080 @30fps,true day night camera with 130 m IR range , optional, fine picture at Ultra-low light,supports compression format H.265, H.265+, H.264+, H.264, 3D Digital Noise Reduction support.
1
-
-
SITC of IP network recoder with following feature
Processor - Dual-core embedded processor . Two-way Talk - 1 channel Input, 1 channel Output, RCA,Video Output - 1 HDMI, 1 VGA , IP Camera Input - 8/16/32 Channel IP , Compression - H.264+/H.264/MJPEG,Video Resolution - 2560 × 1920, 2048 × 1536, 1920 x 1080, 1280 x 1024, 1280 x 720, 1024 x 768 , Hard Disk - 4
SATA Ports, up to 8TB ,Motion Detection - MD Zones: 396 (22 × 18),Recording Mode Manual, Schedule (Regular, Continuous), MD (Video detection: Motion Detection, Camera Blank, Video Loss), Alarm, Stop, Backup Mode - USB Device /Network , Interface Ports - 1 HDMI, 1 VGA, 2 USB(1 USB 2.0 , 1 USB 3.0 ), 1 RS485, 1 RS232,
1
-
-
Supply, Installation, Testing and commissioning of Managable 24 port Switch with Power on Ethernet (PoE) enabled, 10/100, RJ45 Access ports with PoE complete as
required.
2
-
-
Supply, installation, testing and commissioning of of 6 TB HDD all accessories
complete as required.
1
-
-
Supply installation and commissioning of 32 inch LED monitor for disply of camera.
1
-
-
SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM
-
-
-
Supplying installation testing and commissioning of Grid interactive roof top solar photo voltaic power generation system including all the required accessories like Solar PV module, Grid Tie invertor, arrey junction box, cabling & wiring, earthing, surge protection device, FRLSame structure for mounting of solar panel. The cell shall be poly crystaline silicon cells of 6 inch each and module efficiency shall be more than 17%. Solar module shall have linear output warranty with degradation not exceeding 0.7% FRLSom 2nd Year onwards. Minimum 80% power output must be assured at end of 25 years. The FRLSont glass of solar module shall be low iron tempered glass ARC type. Termination box shall be Thermo-plastic, IP 67 or better, UV resistant with built-in-bypass. The nominal power of a single PV module shall be minimum 325 Wp or higher. Positive power tolerance modules only to be used. RF identification tag for each solar module shall be provided inside the module and must be able to withstand environmental conditions. The solar panel shall be complience of IEC 61215, IEC 61730 certified by TUV Rheinland / UL. The solar panel shall be installed as per BOQ
& detailed technical specification.
5
-
-
AUTOMATIC FIRE DETECTION GAS SUPPRESSION SYSTEM IN PANELS
-
-
-
For Main LT Panel.
-
-
-
Supply, fixing, testing and commissioning of Automatic Linear pneumatic Tube Detection based Novec 1230/ FK5-1-12 System for Electrical Panels (consisting of
the following components.
-
-
-
5Lb Novec 1230/ FK5-1-12, DLP Assembly with automatic valve mounted on DOT approved cylinder, push in connector for tube, 2 Kg Novec 1230/ FK5-1-12 gas, mounting bracket, End of Line adopter and low pressure switch for monitoring system
activation.
1
-
-
10 Lb Novec 1230/ FK5-1-12, DLP Assembly with automatic valve mounted on DOT approved cylinder, push in connector for tube, 4 Kg Novec 1230/ FK5-1-12 gas, mounting bracket, End of Line adopter and low pressure switch for monitoring system
activation.
1
-
-
Linear pneumatic heat Detection Tube with all necessary fittings & supports
200
-
-
Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The Control Panel should have provision for integration with Fire Alarm/SCADA/BMS System (Supply to be provide by the end client at 220 Volt AC).
1
-
-
EXTERNAL ELECTRICAL ESTIMATE
-
-
-
TRANSFORMER
-
-
-
Design, manufacture, supply, installation, testing and commissioning of 200 KVA, 11 KV /0.415 KV, 3 phase, 4.5 % impedance, 50 Hz delta/star-11 connected, outdoor type, copper wound transformer, oil immersed ONAN cooled, complete with all fittings such as oil conservator, silica gel breather, thermometer, explosion vent with off Load Tap changing arrangement on HV side with Tapping for variations of high voltage from (+) 5% to (-) 10% in steps of 2.5% each, bi-directional roller, diagrams & rating plate, Oil temperature indicator, & Winding temperature indicator, weather proof Marshalling Box, lifting lugs, first filling of oil, weather proof H.T/L.T cable box etc. complete as per specification. All relays, contacts & CT terminals to be wired upto marshalling box. The Transformer losses should confirm to IS - 1180 Part-1 (2014) with energy efficiency level 2 [0.78 KW at 50% load & 2.23 KW at 100% load shall not exceeds by 5.0% (@ 11 KV) of the maximum total loss values.
1
-
-
DIESEL GENERATING SET
-
-
-
Supply, Installation, testing and Commissioning of Silent type Diesel Generating Set at 0.8 PF, 415 Volts, 50 cycles per second, 1500 rpm, 3 phase, suitable for parallel operation / PLC based synchronization, 0.85 load factor including circuit breaker for isolation, sound proof acoustic and weather proof enclosure, residential type silencer (as per CPCB norms-2) fabricated out of CRCA sheet of 14 / 16 SWG thickness with 9 tank pretreated before powder coating with ventillation system complete in all respects comprising of the following.
-
-
-
Diesel Engine -
-
-
-
Diesel Engine suitable for driving alternator of above rating, compression ignition, 4 stroke cycle, Radiator cooled, turbo charged, battery starting, 1500 RPM, suitable for above output of alternator at 40oC, 50% RH & at 210 M MSL and confirming to BS 5514, BS 649, IS 10000, capable of taking 10% overloading for one hour after 12 hrs of prime continuous loading, complete with all the accessories i.e. tachometer with hour meter, flexible coupling with guard, crank case of steel, crank shaft, conncting rods, electronic governing system, dynamically balanced flywheel, air intake manifold, Air cleaner, anti vibration pads, starter motor, including all other accessories required
-
-
-
Instrument Panel - Engine mounted Instrument Panel fitted with and having digital
display for followings :
-
-
-
Start stop switch with key
-
-
-
Water temperature indication
-
-
-
Lubrication oil pressure indication.
-
-
-
Lubrication oil temperature indication.
-
-
-
Battery charging indication
-
-
-
RPM indication
-
-
-
Over speed indication
-
-
-
Low Lube oil trip indication
-
-
-
Engine hours indication
-
-
-
Alternator -
-
-
-
Synchronous Alternator of above capacity at 0.8 PF, 3 phase, 415 volts, 50 cycles, 4 wire, 1500 RPM, suitable for operation at 40 deg C, 50% RH & at 210 meter above MSL, capable of taking 10% overlioading for one hour after 12 hrs of prime continuous loading, brushless, self excited, self regulated through AVR, continuous duty confirming to IS 4722, BS 2613 suitable for tropical conditions, class H insulation, including terminal box suitable for cable termination as required.
-
-
-
Base Frame - Both the engine and alternator shall be mounted on suitable base frame made of MS channel which shall be installed on cement concrete foundation and vibration isolating arrangement as per recommendations of manufacturer.
-
-
-
Inbuilt Fuel tank of standard capacity complete with inlet and outlet connections, oil indication gauge, drain plug, air breather, fuel transfer system for automatic fuel
refilling system with pump, piping, valves, level indicators etc. complete.
-
-
-
Daily service Fuel tank of 990 liters capacity fabricated out of 2 mm thick MS sheet complete with inlet and outlet connections, oil indication gauge, drain plug, air breather, provision for fuel transfer system, level indicators and all standard
accessories etc. as required.
-
-
-
Exhaust Silencer - Exhaust manifold with residential silencer.
-
-
-
The D G set should be supplied with required hardware for external PLC based auto
synchronization, auto load sharing, auto load management system.
-
-
-
Starting system - 24 Volt DC starting system comprising of starter motors : voltage regulator and arrangement for initial excitation complete with 24 Volts suitable nos.
lead acid type batteries of suitable AH.
-
-
-
Ventillation System - Arrangement for fresh air intake for cooling of the engine &
alternator, extraction, discharging hot air into the atmosphere as per standard specifications.
-
-
-
200 KVA With AMF Panel
1
-
-
Supply, Fixing, testing and Commissioning of Exhaust gas piping system of Class `B' MS pipe as per IS:1239 for upto 150 mm dia and for 200 mm dia & above MS pipe as per IS:3589 with welded joints, cut to required lengths with necessary bends, fittings, flanges, painting over primer coat, with rock wool insulation of minimum 75 mm thick of 150 Kg per cu M density on all sides of exhaust pipe, with chicken mesh wrapping and 26 SWG aluminium sheet cladding complete as required. The aluminum foil should be tightly cladded to insulation surface of pipe. The aluminum cladding shall be locked with sheet metal screws with other sections of aluminium foil. The measurement shall be done on the basis of centre line. (Stack height should be in accordance with emission regulations of CPCB, which will go well above the top most terrace) The exhaust piping system should be suitable for upto 550oC temperature, the surface temperature of exhaust pipe shall not exceed more than 60oC. (The rates are exclusive of support structure) (Note - Final size of exhaust pipe will be confirmed
by the DG vendor after calculating the actual back pressure and submit the same to
-
-
-
150 mm dia (wall thickness - 4.8 mm)
10
-
-
Supply & fabrication of D G exhaust pipe supports by M.S angle iron of size not less than 100 x 50 mm x 6/8 mm duly grouted in the wall through minimum 8 mm thick plate and with suitable MS angle / channel iron structure. The entire MS support structure should be painted by 2 coats of anti corrosive paint over primer coat of approved shade and make. The design of support to be duly approved by the
Structural Consultant / Architect before fabrication and installation.
500
-
-
ELECTRICAL PANELS
-
-
-
MAIN L.T. PANEL WITH PLC BASED LOAD MANAGER
-
-
-
Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of 14 SWG CRCA sheet steel fabricated cubical type Main L.T. Panel
, floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 52, powder coated after proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. FRLS copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable length, 500 volts, 3 phase 50 Hz TPN, electrolytic aluminium as per IS 8623 . The panel feeders shall be suitable for terminating suitable nos. 3.5 / 4 core armoured aluminium cable or Aluminium Bus
-
-
-
All Incoming / bus coupler / Outgoings ACB's shall have inbuilt microprocesor based Over load protection (L), Short Circuit protection (S), Instantaneous Short Circuit protection (I), Earth Fault protection (G), Shunt Trip releases. All ACB should have Ics=Icu=Icw=50 KA for 1 sec, fully rated at 50 deg C ambient temperature & shall be supplied with adopter terminal connection whose orientation can be changed at site. All ACB shall be supplied with all standard accessories i.e. auxillary switch with 4NO + 4NC contacts, cradle, handle, safety shutter in confirmity with IS:60947
-
-
-
All incoming & outgoing MCCB's shall be microprocessor based with O/L & S/C and
E/F protection.
-
-
-
All MCCB's shall be Ics = 100% Icu, with rotary handle & pad locking arrangement, with adjustable O/L & S/C trip setting as per load requirement. All TP MCCB shall be
with heavy duty solid isolable neutral link.
-
-
-
The breaking capacity specified for all ACB's and MCCB's breakers is Ics value
(service rating).
-
-
-
The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmeter, selector switches, cast resin type CT's & PT's, etc. Separate CT's shall be provided for protective and measuring system and for APFCR of capacitor bank with
suitable VA.
-
-
-
Each section of Panel shall have door opearted light of sufficent lux to illumunate that section & each section of capacitor, buscoupler, transformer and DG incomers shall
have exhaust fans for ventilation purpose.
-
-
-
All Energy Analyser / TVM Shall have RS 485 Modbus RTU on board
Communication protocol for SCADA communication.
-
-
-
The Panel shall have a provision for AUTOMATIC FIRE DETECTION GAS SUPPRESSION flooding system for complete panel of each compartment / section including gas bank of required capacity (Note - Gas Supression flooding sysytem
having seperate item).
-
-
-
INCOMERS from 1 Nos. 200 KVA Transformer
-
-
-
1 No. 400 Amp FP Moulded Case Circuit Breaker & 1 No 400 Amp 4 Pole Contactor.
-
-
-
Protection releases / relays, Metering & Accessories for each Transformer incomers
-
-
-
Surge Protection Device - Type - 01 (Class - B), 10/350 µ sec. (100 / 25KA)
-
-
-
Over Voltage / Under Voltage relay / release (3 phase) with timer.
-
-
-
Master trip relay.
-
-
-
Trip Circuit Supervison relay.
-
-
-
TNC switch.
-
-
-
Auto manual selector switch.
-
-
-
1 nos. 0-500 volt range digital type voltmeter with selector switch
-
-
-
1 set of 3 CT's of ratio 200/5A, Class 1.0 accuracy 15 VA burden for metering.
-
-
-
1 set of 3 CT's of ratio 200/5A, Class 1.0 accuracy 15 VA burden for APFCR.
-
-
-
1 set - 415 / √3 / 110 / √3 Class 1.0 accuracy 100 VA burden PT along with primary
and secondary fuse.
-
-
-
1 no. CT's of ratio 200/5A, Class 5P10 for protection.
-
-
-
1 no. 0-200 Amp range digital type ammeter with selector switch.
-
-
-
Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM
6400 of Conzerve or equi.) with RS 485 communication port for communication / report generation.
-
-
-
Power factor meter.
-
-
-
Frequency meter.
-
-
-
3 Nos. LED type phase indicating lamps, each lamp shall be with bakup MCB along
with hooter, auxillary relay, 2 sets of push buttons.
-
-
-
5 Nos. LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP / Trip circuit healthy / DC supply healthy. Each lamp shall be with bakup MCB.
-
-
-
INCOMERS from 1Nos. 200 KVA D G sets
-
-
-
1 No. 400 Amp FP Moulded Case Circuit Breaker & 1 No 400 Amp 4 Pole Contactor.
-
-
-
Protection releases / relays, Metering & Accessories for each D G set incomers
-
-
-
Over Voltage / Under Voltage relay / release (3 phase) with timer.
-
-
-
Trip Circuit Supervison relay.
-
-
-
Reverse power relay.
-
-
-
TNC switch.
-
-
-
Auto / manual / test selector switch
-
-
-
1 Set - 415 /v3 / 110 / v3 Volts PT Class 1.0 accuracy and 100 VA burden along with
primary & secondary MCB.
-
-
-
0-500 volt range digital type voltmeter with selector switch
-
-
-
1 set - 3 CTs of ratio : 600/5A , Class 1.0 accuracy 15 VA each burden for metering.
-
-
-
1 set - 3 CTs of ratio : 600/5A , Class 5P20 accuracy 20 VA each burden for
protection.
-
-
-
0-600 Amp range digital type ammeter with selector switch.
-
-
-
Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM 6400 of Conzerve or equi.) with RS 485 communication port for communication /
report generation.
-
-
-
Frequency meter.
-
-
-
Power Factor meter.
-
-
-
1 No -12 point Temp Scanner with Alarm/ Trip contact for winding & bearing.
-
-
-
3 Nos. LED type phase indicating lamps, each lamp shall be with bakup HRC
fuse/MCB along with hooter, auxillary relay, 2 sets of push buttons.
-
-
-
5 Nos. LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP / Trip circuit healthy / DC supply healthy. Each lamp shall be with bakup HRC
fuse/MCB.
-
-
-
12 window annunciator with accept / reset / test push button for each DG set for following indications and alarm : set fail to start, engine over heat, high temperature, excitation failure, low lube oil pressure, over speed, low fuel oil level, cooling water flow failure, breaker trip, generator fault, DC control supply failure, out of limit voltages
and spares.
-
-
-
Push buttons for Test. Accept. Reset. Fault Reset. Engine start, Engine stop, ACB
close, ACB Trip Emergency stop.
-
-
-
Shut down due to low lube oil pressure/High water temp/Over speed/Low fuel level -
set of 4 indication lamps.
-
-
-
D G control incorporating engine start / stop indicating three attempt facility and on
failure to start, engine lock out.
-
-
-
1 nos battery charger with DC voltmeter and ammeter suitable for the DG sets (250
KVA)
-
-
-
Note : In normal case all three lamps shall be ON to indicate that incoming power supply is available. In case of power resumption after failure buzzer shall ring to indicate the power supply is resumed. There shall be one push button to acknowledge
the same.
-
-
-
The ACB shall be electrically and mechanically interlocked with the bus coupler and
Transformer incomers.
-
-
-
1 nos. 100 amp FP MCCB (25 KA) with KWH meter for Solar Incomer.
-
-
-
BUS COUPLER
-
-
-
1 nos 630 AMP Four Pole, Electrically operated 3 position motorised (220V AC) drawout type ACB's, closing coil (220V AC), trip coil (24V DC), 50 KA Breaking Capacity with all standard accessories i.e. auxillary switch with 4NO + 4NC contacts,
cradle, handle, safety shutter in confirmity with IS:13947-2.
-
-
-
OUTGOINGS:
-
-
-
01 Nos. 315 Amp TP MCCB (25 KA)
-
-
-
04 Nos. 250 Amp TP MCCB (25 KA)
-
-
-
01 Nos. 200 Amp TP MCCB (25 KA)
-
-
-
01 Nos. 160 Amp TP MCCB (25 KA)
-
-
-
07 Nos. 100 Amp TP MCCB (25 KA)
-
-
-
02 Nos. 63 Amp TP MCCB (25 KA)
-
-
-
Main LT Panel as described above
1
-
-
AUTOMATIC POWER FACTOR CORRECTION PANEL (CAPACITOR PANEL)
-
-
-
Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of 14 SWG CRCA sheet steel fabricated cubical type 75 KVAR A P F C Panel consisting of 5 / 10 / 25 KVAR (at 415 Volts rated voltage of bank shall be
440 Volts) capacitor units in tier formation, housed in an integrated cubicle type automatic switching ON and OFF control panel, floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 52, powder coated after proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable length, 500 volts, 3 phase 50 Hz TPN, electrolytic aluminium as per IS 8623 .
-
-
-
The Panel shall have a provision for AUTOMATIC FIRE DETECTION GAS SUPPRESSION flooding system for complete panel of each compartment / section including gas bank of required capacity (Note - Gas Supression flooding sysytem
having seperate item).
-
-
-
All out going MCCB's shall be thermal-magnetic based with inbuilt O/L & S/C release.
-
-
-
All MCCB's shall be Ics = 100% Icu, with rotary handle & pad locking arrangement, with adjustable O/L & S/C trip setting as per load requirement. All TP MCCB shall be with heavy duty solid isolable neutral link. The breaking capacity specified is Ics value. The instrument chamber shall be separate and shall comprise of flush type
ammeter, voltmeter, selector switches, CT's, PT's, etc.
-
-
-
AC3 duty contactors should be used for switching individual capacitor banks.
-
-
-
The fault withstanding capacity of panel & its control gear shall be min. 25 KA rms for
1 sec.
-
-
-
Each section of capacitor panel shall have Verticle hood & exhaust fans for
ventilation purpose.
-
-
-
INCOMING
-
-
-
Incomer circuit breaker has been included in the main panel.
-
-
-
1 set- 3 CTs , ratio 160 / 5A Class 1.0 accuracy 15 VA burden for metering.
-
-
-
1Nos- (400 A) digital Ammeter with selector switch
-
-
-
Micro processor based automatic power factor control relay (3 phase) (including power factor meter) in 6 steps for automatic cut off or add on capacitor units to keep the power factor at 0.95 with variation of loads. All associated auxiliary contactors /
relays shall be provided with in the scope of work.
-
-
-
Phase indicating lamps with HRC fuses, and indicating in each capacitor chamber unit
to indicate On/Off status of capacitor unit.
-
-
-
BUS BARS
-
-
-
200 AMP, 500 Volts, 3 phase 50 HZ TPN high conductivity electrolytic Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by
heat shrinkable sleeves and clips on shrouds for joints.
-
-
-
OUTGOINGS
-
-
-
2 nos. of 63 AMPS TPN 35 KA MCCB and 80 amps AC3 duty contactor with 25 KVAR heavy duty MPP type at 415 V capacitor bank (rated Voltage 440 Volts) , auto manual selector switch, start stop push button for manual operation including on/off
indicating lamps and delay timer complete.
-
-
-
2 nos. of 32 AMPS TPN 35 KA MCCB and 40 amps AC3 duty contactor with 10 KVAR heavy duty MPP type at 415 V capacitor bank (rated Voltage 440 Volts) , auto-manual selector switch, start stop push button for manual operation including
on/off indicating lamps and delay timer complete.
-
-
-
1 no. of 16 AMPS TPN 35 KA MCCB and 20 amps AC3 duty contactor with 5 KVAR heavy duty MPP type at 415 V capacitor bank (rated Voltage 440 Volts) , auto- manual selector switch, start stop push button for manual operation including on/off
indicating lamps and delay timer complete.
-
-
-
Capacitor Panel as described above
1
-
-
DISTRIBUTION PANEL-
-
-
-
Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of cubicle type totally enclosed free standing type moisture, dust and vermin proof Floor Distribution Panel made out of 2.0 mm thick & front cover 1.6 mm thick CRCA sheet complete with following equipments, including digital ammeter with inbuilt ammeter selector switch, digital voltmeter with inbuilt voltmeter selector switch, indicating lamps, CT's, internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. All the incomming and outgoing MCCB shall have 25 KA Ics.The incoming MCCB shall be microprocessor based with O/L & S/C and E/F protection and all Outgoings up to 250A MCCB's may be thermo-magnetic based O/L & S/C protection. All outgoing
-
-
-
L+P PANEL (CHC BLOCK )
-
-
-
INCOMING
-
-
-
1 No. 250 Amp FP MCCB (25 KA)
-
-
-
1 No.AVF Meter with inbuilt selector switch.
-
-
-
1 Set of phase indicating lamps with Single Pole MCB.
-
-
-
1 Set of ON / OFF indicating lamps with Single Pole MCB.
-
-
-
BUSBAR
-
-
-
300 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.
-
-
-
OUTGOING
-
-
-
2 Nos. 160 Amp FP MCCB (25 KA)
-
-
-
01 Nos.63 Amp FP RCCB (300 mA).
-
-
-
06 Nos. 25 Amp FP MCB (10 KA)
-
-
-
02 Nos. 40 Amp FP MCB (10 KA)
-
-
-
14 Nos. 63 Amp FP MCB (10 KA)
-
-
-
Panel described as above
1
-
-
UPS PANEL
-
-
-
INCOMING
-
-
-
1 No. 160 Amp FP MCCB (25 KA)
-
-
-
1 No.AVF Meter with inbuilt selector switch.
-
-
-
1 Set of phase indicating lamps with Single Pole MCB.
-
-
-
1 Set of ON / OFF indicating lamps with Single Pole MCB.
-
-
-
BUSBAR
-
-
-
200 Amp FP Copper busbar with coloured heat shrinkable sleeve.
-
-
-
OUTGOING
-
-
-
01 No. 63 Amp FP MCCB (25 KA)
-
-
-
06 Nos. 25 Amp FP MCB (10 KA)
-
-
-
08 Nos. 40 Amp FP MCB (10 KA)
-
-
-
06 Nos. 63 Amp FP MCB (10 KA)
-
-
-
Panel described as above
1
-
-
AC PANEL-01 (OUT DOOR TYPE)
-
-
-
INCOMING
-
-
-
1 No. 200 Amp FP MCCB (25 KA)
-
-
-
1 No.AVF Meter with inbuilt selector switch.
-
-
-
1 Set of phase indicating lamps with Single Pole MCB.
-
-
-
1 Set of ON / OFF indicating lamps with Single Pole MCB.
-
-
-
BUSBAR
-
-
-
300 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.
-
-
-
OUTGOING
-
-
-
02 Nos.63 Amp FP RCCB (300 mA).
-
-
-
03 Nos.40 Amp FP RCCB (300 mA).
-
-
-
Panel described as above
1
-
-
EXTERNAL LIGHTING PANEL (OUTDOOR TYPE)
-
-
-
Design, Manufacturing, Supply, installation, Testing & Commissioning of Outdoor Type Panel with Front & Back double door, Top canopy, Mounting on Floor M.S. Stand etc totally enclosed free standing type water, moisture, dust and vermin proof Sub Distribution Board made out of 2.0 mm thick CRCA sheet complete with following equipments, including ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indicating lamps, CT's, internal wiring with suitable size wires/ cable,
interconnection, painting etc as required.
-
-
-
INCOMING
-
-
-
1 No 100 Amp FP Moulded Case Circuit Breaker (25 KA) with 100 Amp 4 Pole
Contactor & Timer.
-
-
-
1 No. Digital AVF Meter with inbuilt selector switch and CT' & SP MCB.
-
-
-
1 Set of phase indicating lamps.
-
-
-
1 Set of ON/OFF indicating lamps with SP MCB.
-
-
-
BUS BARS
-
-
-
200 Amp FP aluminium busbar with coloured heat shrinkable sleeve.
-
-
-
OUTGOING
-
-
-
08 Nos. 25 Amp DP MCB (10 KA)
-
-
-
03 Nos. 40 Amp DP MCB (10 KA)
-
-
-
Panel described as above
1
-
-
Supplying of 11 KV grade aluminium conductor, cross linked polyethylene (XLPE) insulated individual core screened, flat steel/strip armoured PVC sheathed cable
complete as required. 3C x 240 Sqmm, 11 KV XLPE
50
-
-
Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor PVC insulated cable including termination complete as required in existing cable tray. 1C x 35 sq.mm PVC Insulated cu wire including termination etc.
80
-
-
Supply Supply & Laying of following sizes of 1.1KV grade Copper conductor XLPE insulated and FRLS PVC sheathed armoured control cable including termination
conforming to relevant IS.
-
-
-
4 core, 2.5 sq.mm.
30
-
-
10 core, 2.5 sq.mm.
30
-
-
12 core, 2.5 sq.mm.
30
-
-
Supply, erection, testing and commissioning of following sizes of TV splitter of
aluminium die cast body in suitable size of G.I. Box.4 way
1
-
-
Supply, erection, testing and commissioning of following co-axial cable in existing conduit.RG-11
50
-
-
Supply & fixing of following size (GP RACEWAY- Fabricated from GP Sheet) race ways for electrical & LV wiring including neoprene gasket in joints, cutting the floor & jaming the race way / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work) as per site requirement. The thickness of raceway & cover shall be as per technical specification.
-
-
-
100 mm wide x 40 mm deep.
10
-
-
200 mm wide x 40 mm deep.
10
-
-
Supply & fixing of following size of Raceway Junction Box made out of GP Sheet for electrical & LV wiring including, cutting the floor & jaming the junction box / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work).(Junction box to be provided as per drawing/ as per site requirement & as per specification). The thickness of junction box shall be a as per thechnical specification.
-
-
-
150 mm wide x 50 mm deep.
22
-
-
250 mm wide x 50 mm deep.
3
-
-
Supply & Fixing of Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006.
8
-
-
EXTERNAL PLUMBING WORK
-
-
-
WATER SUPPLY EXTERNAL
-
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.
-
-
-
External Work
-
-
-
25mm nominal nominal bore
25
-
-
32mm nominal nominal bore
135
-
-
40mm nominal nominal bore
135
-
-
50mm nominal nominal bore
188
-
-
65 mm nominal nominal bore
220
-
-
Providing & Fixing of Garden hydrant outlet consisting 1 No. 25mm dia. Ball valve,( Brass) for connecting rubber hose, pipes & fittings.
11
-
-
Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends)
-
-
-
25 mm dia, nominal bore
12
-
-
32 mm dia, nominal bore
3
-
-
40 mm dia, nominal bore
3
-
-
50mm nominal bore
3
-
-
65mm nominal bore
3
-
-
Constructing masonry Chamber 60x45x50 cm,inside with 75 class designation brick work in cement mortar 1:5 (1 cement:5 fine sand) for water meter complete with C.I. Doble flap surface box 400x200x200mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. With F.P.S. bricks
10
-
-
Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete.(WTP Room Abow the UGT.)50 mm dia,
nominal bore
10
-
-
65 mm dia, nominal bore
10
-
-
80 mm dia, nominal bore
1
-
-
Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of
approved quality. 50 mm dia, nominal bore
10
-
-
65 mm dia, nominal bore
10
-
-
80 mm dia, nominal bore
1
-
-
Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe
and making long screws etc. complete.
-
-
-
32 mm dia, nominal bore
1
-
-
40 mm dia, nominal bore
1
-
-
50 mm dia, nominal bore
4
-
-
65 mm dia, nominal bore
4
-
-
Providing & fixing in position precast RCC manhole cover and frame of reqd. shape and approved quality.EHD - 35 Circular shape 560 internal dia.
6
-
-
Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement
-
-
-
With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
6
-
-
Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :50 mm dia
6
-
-
Providing and fixing cast iron wafer type butterfly valves (PN-10) complete with 2 nos. matching flanges (Table-E),bolts, nuts, 3.0 mm thick insertion neoprene gasket.
-
-
-
40mm dia
1
-
-
50mm dia
1
-
-
65mm dia
4
-
-
80mm dia
1
-
-
Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged
end & PN 16 rating as specified.65mm dia.
1
-
-
Providing & fixing CI `Y' Strainer (screwed/ flanged) with stainless steel fine wire mesh perforated sheet basket with necessary flange/ unions nuts, bolts and washers
complete as required.65mm nominal bore
1
-
-
Providing and fixing M.S fabricated hot dipped galvanized coating puddle flange comprising of 600 mm dia long M.S class 'B' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: Underground / Overhead Tanks.)
-
-
-
25mm dia pipe, 600mm long with size of 250x250x6 mm MS plate
1
-
-
50mm dia pipe, 600mm long with size of 350x350x6 mm MS plate
2
-
-
65mm dia pipe, 600mm long with size of 350x350x6 mm MS plate
3
-
-
100mm dia pipe, 600mm long with size of 400x400x6 mm MS plate
3
-
-
Providing, laying, Jointing, Testing and commissioning of uPVC pressure pipes of 10Kg/Sqcm pressure rating class 5 (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation Including laying cement concrete 1:2:4 alround UPVC pipe including bed concrete and thrust blocks at bends as per
standard design.
-
-
-
25 OD mm.
202
-
-
32 OD mm.
89
-
-
40 OD mm
128
-
-
50 OD mm
65
-
-
63 OD mm
2
-
-
Supply, installation, testing and commissioning built with Drinking Water R.O. unit with micron filtration pre-treatment unit, skid mounted R.O. module with pressure pump and pressure tank, drinking water cooler (High quality SS Tank for Storage 80 lts) , complete in all respects. ( Make & Model No. Eureka Forbes Pure Chill RO Storage
Cooler cum Purifier or Equivalent)
1
-
-
EXTERNAL SEWERAGE & DRAINAGE INSTALLATIONS
-
-
-
Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and
direction of E/I.
-
-
-
All kinds of soil
-
-
-
(ii) For classification of soil item-B
25
-
-
Providing laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of
joints etc. complete.
-
-
-
150 mm diameter
450
-
-
200 mm diameter
30
-
-
250 mm diameter
16
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded
stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design.
-
-
-
100 mm diameter
45
-
-
150 mm diameter
460
-
-
200 mm diameter
30
-
-
250 mm diameter
16
-
-
Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design.150x100mm size P type With FPS bricks (COVER MIN. 4.5 KG & FRAME MIN.2.7 KG )
30
-
-
Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.
-
-
-
150 mm dia RCC pipe
105
-
-
250 mm dia RCC pipe
350
-
-
300 mm dia RCC pipe
70
-
-
450mm dia RCC pipe
5
-
-
Providing and laying in position cement concrete of grade excluding the cost of centering and shuttering - all work up to plinth level.1:5:10 (1 cement : 5 coarse sand : 10 graded ston aggregate 40 mm nominal size)
15
-
-
Construction brick masonry manhole in cement mortar 1:4 (1cement : 4coarse sand) RCC top slab with 1:2:4 mix 9 with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement
: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.
-
-
-
Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class
designation 7.5
50
-
-
Extra for depth for manholes .Size 90 x 80 cm with FPS bricks designation 7.5
30
-
-
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) complete as per
115
-
-
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C.
horizontal grating with frame complete as per standard design :
-
-
-
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
22
-
-
Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter
1
-
-
Design, Supplying, installing, testing & commissioning of Effluent Treatment Plant of 5 KLD (excluding excavation, back filling & disposal of surplus earth and Civil
construction work) for the following duty:
-
-
-
Effluent from OT Scrubs, blood bank, labs etc. Some solvent/ chemical waste originating typically from hospital complex shall also be discharged into the ETP. Design to take consideration of same.
-
-
-
INLET EFFLUENT CHARACTERSTICS
-
-
-
PH : 5.5 - 9.0
-
-
-
BOD : 250 - 600 mg/l
-
-
-
S. Solids : 200 - 650 Mg/l
-
-
-
COD : 600 - 1200 mg/l
-
-
-
Oil & Grease : 50-140 mg/L
-
-
-
Effluent discharge standard after treatment
-
-
-
pH - 6.0 – 8.5
-
-
-
BOD - Less than 150 Mg/L
-
-
-
S. Solids - Less than or equal to 100 Mg/L
-
-
-
COD - Less than or equal to 300 Mg/L
-
-
-
Oil & Grease - Less than 5 Mg/L
-
-
-
Effluent treatment plant shall include the following items:
1
-
-
Add GST 18 %
18
-
-
Add Labour cess 1%
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements