State Building Construction Corporation Limited Tender
Search from across the categories, cities, and authorities to find the latest Jharkhand tenders. Every Jharkhand tender is curated from credible sources of government websites (eProcurement Jharkhand portal) and newspapers, thus ensuring the credibility of the information presented to you. For more information on Jharkhand tender bidder registration, the login process and more read the FAQs section on this page.
Costs
EMD
₹ 8,17,000Document Cost
₹ 10,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_JSBCC_82465_1Bid Award Id
ViewTender No
JSBCCL/98/2023-24Tender Authority
State Building Construction Corporation Limited ViewPurchaser Address
-Website
http://jharkhandtenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).
173.48
-
-
... More
Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).
110
-
-
... More
Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.
49.75
-
-
... More
Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.
136.05
-
-
... More
Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.
6.6
-
-
... More
Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
466.77
-
-
... More
Providing 112mm thick reinforced designation 100A brickwork fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including the cost of screening carriage of material scaffolfing raking out joint to 15mm depth curing taxes and royalty (but excluding the cost of reinforcement ) all complete as per building specification and direction of E/I.
129.04
-
-
... More
Extra for brick work for each consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.
203.23
-
-
... More
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
-
-
-
... More
: 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)
54.26
-
-
... More
1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
38.68
-
-
... More
1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)
3.92
-
-
... More
1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 40 mm nominal size)
19.08
-
-
... More
1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
9.55
-
-
... More
Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
5.63
-
-
... More
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).
43.12
-
-
... More
Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
476
-
-
... More
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
169.89
-
-
... More
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)
74.71
-
-
... More
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
322.98
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for :
-
-
-
... More
Foundations, footings, bases of columns, etc. for mass concrete
263.27
-
-
... More
Walls (any thickness), including attached pillars, butters, plinth and string course etc.
39.4
-
-
... More
Suspended floors, roofs, landings, balconies and access platform
1232.35
-
-
... More
Lintels, beams, plinth beams, girders, bressumers and cantilevers
1030.4
-
-
... More
Columns, Pillars, Piers, Abutments, Posts and Struts
1092.46
-
-
... More
Stairs, (excluding landings)
171.95
-
-
... More
Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like
11.25
-
-
... More
Weather shade, Chajjas, corbels etc., including edge
391.15
-
-
... More
Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but ,
excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
5.8
-
-
... More
Providing precast cement concerete Jali 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 6 mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughing cleaning, fixing , excluding, plasteringof the jambs, sils and shofts. 50 mm thick
198.4
-
-
... More
Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.
168.5
-
-
... More
Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.
1.29
-
-
... More
Supplying, fitting and fixing 38 mm thick good quality, well dressed and well seasoned Sal wood fully glazed shutters in windows with iron fittings such as hinges, sliding doors, bolts, tower bolts, handles or rings, sand blocks as per schedule and 3 mm thick plain glass fitted with sal wood beads, taxes all complete as per building specification and direction of E/l.
43.2
-
-
... More
Supplying , fitting and fixing 38 mm thick good quality , well dressed and well seasoned sal wood 1/3rd glazed and 2/3 paneled shutters in doors and windows with 25 mm thick panels with one side plain and other side chamfered with aluminium fittings such as hinges, sliding doors, bolts, tower bolts, handles or rings, hooks and eyes cleats, sand blocks as per schedule and 3mm thick plain glass panes fitted with sal wood beads and taxes all complete as per building specification and direction of E/l.
30.87
-
-
... More
Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
25.2
-
-
... More
Supplying fitting and fixing glass panes including supplying putty. Beads and nails after taking out old and broken glass panes and disposal of debris all complete as per building specification and direction of E/I. 4mm plain
218.12
-
-
... More
Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).
19.62
-
-
... More
Providing Tor steel reinforcement of 10mm. ,12mm & 16mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.
-
-
-
... More
(a) 10mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).
20.19
-
-
... More
(b) 12mm,16mm,20mm,25mm,32mm TMT Fe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL).
50.26
-
-
... More
Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)
1865.77
-
-
... More
Supplying, fitting and fixing 20 guage G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.
485.51
-
-
... More
Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.
155.92
-
-
... More
Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.
124.48
-
-
... More
Providing 12 mm cement plaster (1:3) with clean coarse sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curring, taxes and royalty all complete as per building specification and direction of E/l.
10.35
-
-
... More
Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.
1368.64
-
-
... More
Providing and laying Double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less then 0.08% and conforming to IS: 15622/ISO 13006 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 Coarse sand0, jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with wite cement and matching pigments etc, complete Size of tiles 600 x 600 mm.
3319.59
-
-
... More
Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.
336.55
-
-
... More
Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
65.76
-
-
... More
Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
4801.08
-
-
... More
Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
2645.35
-
-
... More
Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.
725.76
-
-
... More
Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.
5059.05
-
-
... More
Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/l.
682.93
-
-
... More
Making 6x6mm grooves in plaster surface over walls truely horizontal or verical as specified at regular intervals, at all heights including cleaning, finishing scaffoding and curing with all leads and lifts of water all complete as per building specification and direction of E/l.
640
-
-
... More
Extra for cleaning the old surface by scrapping the entire old white wash or colour wash including cost of scaffolding all complete as per direction of E/I.
16093.71
-
-
... More
Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.
2669.3
-
-
... More
Providing two coats of plastic emulsion paint of approved shade and make over old surface including washing, cleaning and preparing the walls, scafolding, washing of floor and taxes all complete as per building specification and direction of E/l.
11642.95
-
-
... More
Providing french spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed french polish including preparing the surface after cleaning, removing dirt, scales, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.
719.06
-
-
... More
Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)
1469.43
-
-
... More
Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.
2454.07
-
-
... More
Dismantling R.C.C.work including stacking serviceable materials in countable stacks within 15M. lead and disposal of unserviceable materials with all leads all complete as per direction of E/l
14.01
-
-
... More
Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.
2632.3
-
-
... More
Dismantling old plaster and pointing in cement or lime and raking out joints to 15 mm. depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/l.
4817.81
-
-
... More
Taking down old door and window shutters including stacking serviceable materials within 15M. lead and disposal of unserviceable materials with all leads all complete as per direciton of E/l.
543.5
-
-
... More
Taking down chowkhat in doors including stacking serviceable materials within 15M. lead and disposal of unserviceable materials with all leads all complete as per direciton of E/l.
128.5
-
-
... More
Taking down chowkhat in Windows including stacking serviceable materials within 15M. lead and disposal of unserviceable materials with all leads all complete as per direciton of E/l.
415
-
-
... More
Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l.
501
-
-
... More
Water proofing for old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flextble material brush, roller or spray for water proofing coating per manufacturer Specifications with following steps :-(a)surface preparation .-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing (loose paint / coating, and cement laitance by cleaning with compressed air water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage leakage. On identification of seepage cement grouting to be done with non shrink expanding admixture of Sika India Pvt.L.td.) MYK Schomberg / Dr Fixiti/ Fosroc or equivallent. Providing and reparing of all Corner and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150Mrn X 150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic pc?' lymer of Sika/ Fosroc/MYK Schomberg/Dr 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent.,Befor 'Chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar-including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.(b)lst Coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitiot.is material on surface saturated dry roof and inside wall of Parapet.Wall upto 600 mm by brush or roller . After 1st coat of application , 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat shOUld be applied @1.50 kg/Sqmt/coat. For the purpose of measurer-11609-1'e entire treated surface will be measured." (c) 2nd Coat :-To apply the 2nd coat of two component acrylic modified read to use, flexible cementtiOus material right angle to the 1st. coat over the glass fibre laid surface: 2nd coat-,should be applied @ 0.7 Sqmt/coat. For the purpose of measurement the entire treated surface will be measured." After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofing Brand:- Sika Topseal 109hi / Fosroc Brushbond RFXI Dr. Fixit Pidiffin 2K / MYK Aquafin TG . Product Performance - Chemical Base Part A: Acrylic copolymer, Part B: Specially graded cementitious powder - Density 1.6 kg/I (mixed density) at +27°C Tensile Strength -2 Nimm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Siren th -2 f\l/mm2 concrete failure Accordin' to ISO4624) Slant-Shear Bond Strength -4 Nimm2 (According to FIP 5.15) Elongation at Break -35% Without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) )Protection of treated surface with PCG :- The treated surface should be covered with 25mm/50mm F'CC of M-20 grade (1.1.5:3). with proper slope ( 1:120) towards the rain outlets in alternate panels of 2 mt x 2 mt keeping 6 rnm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 co of 100 ml per bag of of cement to be added in the screed concreie(paid separately.for this items).All corners shall be chamfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface should be packed prorSeqswith ridti:corict'ete and the peripheral mouth to be sealed with,moisture insensitive epoxy putty of. Sika India .Pvt.Ltd. / MYK Schornbefg /Dr Fixit/Fosroc .For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with POlysulphide Sealant.(Paid Separately). Be d - Sika India Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc . Warranty for five years.
3923.31
-
-
... More
Covering of treated surface with PCC :-providing 25 mm thick Cement Concrete M20 (1:1:5:3) maintaining slope in alternate 2 mt x 2mt panels With approved quality of stone chips of 20mm to 6 mm size graded and Cleaned sand of F.M.2.5 to 3 including screening, shuttering, and mixing Cement concrete in mixer with admixture of integral water proofing and Placing in position, striking curing, taxes and royalty all complete as per Building specification and direction of E/I. Panels that has been left should Be casted next day. There should be 6 mm gap between panels .brand- Sika _ plastocrate plus, MYK proof WP 10, Fosroc- Conplast X 421 ic Dr Fixit Pidiproof LM+
3923.31
-
-
... More
Providing and mixing liquid integral water proffing compound in conctrete of plaster as manufacturer specification and as per direction of engineer in charge. Brand. Sika plastocrate plus, MYK proff WP 10, Fosroc-Conplast x 4211C, Dr.Fixit, Pidiproff LW+ or Equivalent
338.29
-
-
... More
Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysuiphide Sealant (Porin.g Grade)as per drawings and technical specificationsi6nd direction of E in Charge. (with 18% GST) B rand Sika Polysulphide, Fosrpc-Thioflex 600 Dr. Fixit Pidiseal PS(42P. MY K Seal PS or Euivalent.
323.37
-
-
... More
Cost of Driling 200mm x 165mm x 125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.
-
-
-
... More
(a) From 0.00 M to 50.00 M below G.L.
75
-
-
... More
(b) From 51.0 M to 150.00 M
100
-
-
... More
Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 metre submersible copper conductor cable in single/double run shall be provided with each pump.
Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages
2 HP
1
-
-
... More
Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914.
F.A.S.D starter
1
-
-
... More
Supply fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quaility as per IS:1239 ( part 01 ) 2004
115
-
-
... More
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
332.48
-
-
... More
Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
184.75
-
-
... More
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
129.04
-
-
... More
Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick
50.4
-
-
... More
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
633.16
-
-
... More
Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
40
-
-
... More
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
1528.8
-
-
... More
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement
168.04
-
-
... More
Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur green marble
452.25
-
-
... More
Extra for pre finished nosing to treads of steps of marble stone
211.8
-
-
... More
25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class teak wood
53.09
-
-
... More
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.
644.81
-
-
... More
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
-
-
-
... More
75 mm diameter
275
-
-
... More
110 mm diameter
1028.3
-
-
... More
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
-
-
-
... More
Coupler 75 mm
94
-
-
... More
Coupler 110 mm
168
-
-
... More
Single pushfit Coupler 75 mm
94
-
-
... More
Single pushfit Coupler 110 mm
94
-
-
... More
Single tee with door 75x75x75 mm
94
-
-
... More
Single tee with door 110x110x110 mm
94
-
-
... More
Single tee without door 75x75x75 mm
94
-
-
... More
Single tee without door 110x110x110 mm
94
-
-
... More
Bend 87.5° 75 mm bend
94
-
-
... More
Bend 87.5° 110 mm bend
193
-
-
... More
Shoe (Plain) 75 mm Shoe
94
-
-
... More
Shoe (Plain) 110 mm Shoe
193
-
-
... More
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
319
-
-
... More
Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
609.16
-
-
... More
Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
2111.06
-
-
... More
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
20146.13
-
-
... More
Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface
4450.76
-
-
... More
Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm dia for all depth.
75
-
-
... More
Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in Charge.
3
-
-
... More
Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead For thickness of tiles 10 mm to 25 mm
1623.39
-
-
... More
Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).
28.8
-
-
... More
Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.
891
-
-
... More
Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of
wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary
bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm
with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)
300
-
-
... More
Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
6
-
-
... More
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. 16.78.1 With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30
39.84
-
-
... More
Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site.
28.8
-
-
... More
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved
color design and pattern.
362.2
-
-
... More
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap
62
-
-
... More
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 178 mm
4
-
-
... More
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia
66
-
-
... More
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia
62
-
-
... More
Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
62
-
-
... More
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank.
45000
-
-
... More
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
74
-
-
... More
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore
56
-
-
... More
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.
18.52.1 15 mm nominal bore
48
-
-
... More
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore
113
-
-
... More
Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole
113
-
-
... More
Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms
53
-
-
... More
Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
56
-
-
... More
Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length
113
-
-
... More
Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 gms
113
-
-
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc
-
-
-
... More
15 mm nominal dia Pipes
140
-
-
... More
20 mm nominal dia Pipes
485
-
-
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work
-
-
-
... More
25 mm nominal dia Pipes
308
-
-
... More
32 mm nominal dia Pipes
455
-
-
... More
40 mm nominal dia Pipes
340
-
-
... More
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
480
-
-
... More
Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg
3
-
-
... More
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
1
-
-
... More
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
-
-
-
... More
For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)
266.93
-
-
... More
For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)
283.92
-
-
... More
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)
102.72
-
-
... More
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
177.43
-
-
... More
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia
25
-
-
... More
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia
25
-
-
... More
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
4.91
-
-
... More
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
4.91
-
-
... More
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
2
-
-
... More
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia
2
-
-
... More
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp
2
-
-
... More
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity
900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
178.2
-
-
... More
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) 25 mm thick
43.75
-
-
... More
Providing and fixing Sink Cock with Swinging casted spout
4
-
-
... More
Clearing Grass and Remove of Rubish , Clearing grass and remove of rubbish up to a distance of 50 meter outside the periphery of the area. By manual Means.
0.66
-
-
... More
Carriage of materials from source to site work including loading & unloading all complete job as per specification and direction of E/I
-
-
-
... More
Sand
874.91
-
-
... More
Aggregate
660.76
-
-
... More
Stone Metal
9.81
-
-
... More
Brick
103.95
-
-
... More
Fly Ash Brick
196.06
-
-
... More
Boulder
28.8
-
-
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with moduler switch, modular plate suitable GI box etc as required Group C
167
-
-
... More
Wiriug for light/power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, along with 1 No 4 sq.nrm FR PVC insulated copper conductor single core cable for loop carthing etc as required.
699
-
-
... More
Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.
-
-
-
... More
2 x 1.5 sq.mm + 1 x 1.5 sq. mm earth wire
188
-
-
... More
2 x 2.5 sq.mm + 1 x 2.5 sq. mm earth wire
240
-
-
... More
2 x 4.0 sq.mm + 1 x 4.0 sq. mm earth wire
145
-
-
... More
2 x 6.0 sq.mm + 1 x 6.0 sq. mm earth wire
90
-
-
... More
Supplying and drawing following sizes of FRPVC insulated copper conductor single core cable in existing surface / recess steel PVC conduit including dismentling as required.
-
-
-
... More
2 x 1.5 Sq.mm
1276
-
-
... More
3 x 1.5 Sq.mm
680
-
-
... More
2 x 2.5 Sq.mm
812
-
-
... More
3 x 2.5 Sq.mm
360
-
-
... More
3 x 4 Sq.mm
380
-
-
... More
3 x 6 Sq.mm
100
-
-
... More
Rewiring for light point/fan point/exhaust fan point/ call bell point 1.5 sq.mm FR PVC insulated copper conductor single core cable in existing surface / recessed Steel/PVC conduit including dismantling as required
-
-
-
... More
Group A
203
-
-
... More
Group C
256
-
-
... More
Supplying and fixing of following sizes of PVC Conduit along with accesseories in surface/recess including cutting the wall and making good the same in core recessed conduit etc. as required.
-
-
-
... More
20 mm
1460
-
-
... More
25 mm
554
-
-
... More
Supplying and fixing of following modular switch / soket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
-
-
-
... More
5/6 amps, one way switch
90
-
-
... More
5/6 amps, 3 pin socket outlet
90
-
-
... More
Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
32
-
-
... More
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
122
-
-
... More
Supplying and fixing following size / modules , GI box along with modular base & cover plate for modular switches in recess etc as required.
-
-
-
... More
1 or 2 module (78mm x 78mm x 45mm)
124
-
-
... More
4 or 5 module(78 mm x 140 mm x 50 mm)
67
-
-
... More
6 module(78 mm x 205 mm x 50 mm)
27
-
-
... More
Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch. corutection, painting etc. as required (For light plugs to be used in non residential buildings)
100
-
-
... More
Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fxing 6 pin 15/16 amps modular socket outlet and l5/16 amps modular switch. connection, painting letc. as required (For light plugs to be used in non residential buildings)
33
-
-
... More
Supplying and fixing 2 pin,5 amp ceiling rose on existing junction box/wooden block including connection etc as required.
261
-
-
... More
Installation testing and commissioning of pre-wired, fluorescent fitting ./ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly / wall. including connection with 1.5 aq.mm FR PVC insulated . copper conductor single core cable and earthing etc. as required.
33
-
-
... More
Installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. including supplying and fixing ball and socket arrangement , 2 nos down rods of 20mm dia x 1.6 mm thick steel conduit upto 30cm length. painting and wiring the down and connection with 1.5 sq. mm PVC insulated, copper conductor, single core cable and eartning etc. as required
32
-
-
... More
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc. as required.
32
-
-
... More
Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc as required.
16
-
-
... More
S/F rewireable double pole/ TP&N switch disconnector :- Providing and fixing following DP/TP&N sheet metal switch disconnector fuse unit in the existing metal board with rewireable type fuses, including drilling holes in metal board . making connections. etc. as required.
-
-
-
... More
32 amps, double pole
4
-
-
... More
63 amps, double pole
2
-
-
... More
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (but wiithout MCB/RCCB/Isolator)
-
-
-
... More
8 way, Double door
10
-
-
... More
12 way Double door
10
-
-
... More
16 way Double door
4
-
-
... More
Supplying and fixing 6 amps to 32 amps rating, 240 volts, 'C' curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.
-
-
-
... More
6/32 amps, Single pole
182
-
-
... More
40 amps, SPN
10
-
-
... More
6/32 amps,DP
6
-
-
... More
40 amps, DP
1
-
-
... More
50/63 amps, DP
5
-
-
... More
50/63 amps, TPN
1
-
-
... More
Supplying and fixing following rating double pole,240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
2
-
-
... More
Earthing with G.I. earth pipe 4.5 mtr long . 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.
3
-
-
... More
Earthing with G.I. earth plate 600mm x 600mm x 6mm thick including accessories, and providing masonry enclosure with cover plate having Iocking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.
1
-
-
... More
Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal or cock and salt complete etc. as required. (with charcoal or coke and salt)
6
-
-
... More
Supply and laying 8 SWG copper wire at 0.5 metre below ground level for conductor earth electrode, including solding etc. As required.
98
-
-
... More
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from carth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
50
-
-
... More
Providing and fxing 25mm x 5mm G.I. strip on surface or in recess for connection etc. as required.
30
-
-
... More
Providing and fixing 4.00mm dia copper wire on surface or in recess for loop earthing etc. as required.
90
-
-
... More
Providing and Fixing Lightning conductor finial, made of 25mm dia 300mm long GI tube, having single prong at top, with 85mm dia 6mm thick GI base plate including holes etc. complete as required.
8
-
-
... More
Providing and fixing of GI tape 20mm X 3mm thick on parapet or surface of wall for lighting conductor etc complete as required.(for horizontal run)
670
-
-
... More
Providing and fixing of GI tape 20mm X 3mm thick on parapet or surface of wall for lighting conductor etc complete as required.(for Vertical run)
185
-
-
... More
Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of l.l KV grade of size exceeding 95 sq mm but not exceeding 185 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
90
-
-
... More
Laying of one number additional PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 35 sq mm but not exceeding 95 sq. mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.
30
-
-
... More
Layrng and fxing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with lmm thick saddle)
40
-
-
... More
Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq mm direct in ground but excluding , sand cushioning, protective covering as required.
210
-
-
... More
Laying of one number PILCA/PVC insulated and PVC sheathed/ XLPE power cable of grade exceeding l.lKV but not exceeding I 1 KV of size not exceeding 120 sq mm direct in ground including excavation, and cushioning, protective covering and refilling the trench
100
-
-
... More
Erection of RCC/ PCC pole of following length in brick ballast and ramming the foundation, finishing with l50mm thick cement concrete (l:3:6) layer on top with including excavation and refilling etc as required. Above 6.5 metre and upto 8.0 metre
33
-
-
... More
S.I.T.C. Of following rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in Existing Pole / Pipe for Supply voltage 100-270V AC, 50 Hz. Luminarie shell be confirm to IS:10322 part-5 / section -5 and shall be complete with all neccssary accessories as required.
-
-
-
... More
90/100 W LED Flood Flood light
11
-
-
... More
120 W LED Flood Flood light
2
-
-
... More
S.I.T.C. Of following rating recess / surface mounted LED round / squre shape down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS 10322 part-5/section-2 or IEC:62772 with all neccssary accessories as required. 6/7W LED Round Down light
63
-
-
... More
Supply, Installation, testing and commissioning of following size ceiling fan 3 blades confirming to IS 374:2019 including wiring the down rods of standard length (upto m cm) with 1.5 Sq. Mm FR PVC insulated, copper wire suitable for 230 V 50 Hz, Single phase supplt etc. complete as required. 1200 mm (48") BLDC 5 star rating 32W Ceiling Fan
149
-
-
... More
Supplying installation testing and commissioning following ration surface mounted LED tube light fittings suitable for 230V 50Hz. Single phase supply etc. complete as required. 20/22 W LED Tube Light
254
-
-
... More
Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) With "P" trap (a)10.0 lit. low level PVC cistern
28
-
-
... More
Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) 580 mm long (c) with 10.0 lit. low level P.V.C. cistern
49
-
-
... More
Supplying fitting fixing the following items Complete with all material as per specification and direction of E/I C.P. brass towel rail 20mmX600mm with bracket container
71
-
-
... More
Supplying, materrials and labour for constructing inspection chamber of designation class 75B brick size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.
63
-
-
... More
Supplying labours, tools and tackles for cleaning filled and choaked man hole, septic tank, inspection chamber, gullay pits, sewerage tank etc. in all lift and disposal of spoils upto a lead of 50 M all complete as per specification and direction of E/l.
32.98
-
-
... More
Supply of Exhaust metal Fan 230mm(9"): Supply and fitting of 230mm(9"), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required.
16
-
-
... More
Supply of Metal Exhaust Fan 12"(300mm): Supply of 12"(300mm), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required.
20
-
-
... More
Supply of Metal Exhaust Fan 15"(380mm): Supply of 15"(380mm), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required
6
-
-
... More
LED Bulb 9W/10W : Supplying and fixing of LED 9W /10W bulb and accessories as required. ( Make -Wipro/Bajaj / Havells/ Philips)
108
-
-
... More
Bulk head 10 LED Fitting: Supply and fixing of 10W LED, surface mounted bulk head PVE water proof housing for indoor/ outdoor.
3
-
-
... More
62.5 kVA DG set :Supply, fitting, fixing, errection and commissioning along with civil foundation work of 62.5 kVA D.G. Set, 415 Volts, 3 Ph. Silent Diesel Engine driven generating set as per IS:1460 & IS : 13018 and alternator as per IS:13364 complete with sound proof company make canopy (Acoustic Enclosure suitable for 62.5 kVA D.G. Set.) with breaker panel (automatic Control Panel) and civil foundation work as per the norms of 62.5 kVA Silent D.G. Set with suitable arrangement for Al./Ar./C etc as required. (Make:- Sterling and Wilson Powergen Private Limited with MTU Engine SDGSC - 3 Cotroller / Kirloskar (GREEN) / Jakson Limited / Mitsubishi / Cater Pillar/Sterling)
1
-
-
... More
Split type AC 1.5 T, 5 star: Supply, installation, commissioning of split type Inverter AC 1.50T capacity, 5 star rating as per IS-1391, part-II. ( Make-Hitachi, Daikin, Carrier)
3
-
-
... More
Supplying fiting fixing Copper tube of size( 1/4)" for split AC
12
-
-
... More
Supplying fiting fixing Drain pipe for split AC
18
-
-
... More
Outdoor Stand for 1.5 tr Split AC
3
-
-
... More
5 KVA wall monted Stublizer
3
-
-
... More
3 core PVC insulated PVC sheathed copper conductor flat submersible cable. Supplying , Flat flexible submersible cable with ,copper conductor , PVC insulated and PVC sheathed as IS:7098 3 Core 4 Sq mm. Copper wire
130
-
-
... More
Supply, installation of 7.0m height OctagonalHot -dip glavinized pole with top dia 70mm, bottom dia 130mm & made of 3mm thick sheet, base plate dimension 200x200x12mm(L X B X T) including suitable sizes of foundation bolt all complete as required.( without arm) Make_Bajaj/Havells/Surya/ Philips
33
-
-
... More
Supply, installation 0.5m single arm suitable for 70mm top pole all complete as per engineer in charge.
30
-
-
... More
Supply, installation 0.5m double arm suitable for 70mm top pole all complete as per engineer in charge.
3
-
-
... More
Supply of following PVC/XLPE insulated PVC sheathed, heavy duty , armoured electrical cable with aluminium conductor for working voltage upto and including 1.1 kV grade( Confirms to IS :1554, part-1)
-
-
-
... More
10 sq.mm, 4 core
900
-
-
... More
25 sq.mm, 3.5 core
115
-
-
... More
35 sq.mm, 3.5 core
100
-
-
... More
95 sq.mm, 3.5 core
40
-
-
... More
120 sq.mm, 3.5 core
110
-
-
... More
S.I.T.C of floowing rating LED Street lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage'1.00-270V AC,50Hz. Luninarie shall be confirm to IS: 10322 part-5 / section-3 and shall be complete with all neccssary accessories as required 70/72W LED Street light
36
-
-
... More
Providing and laying earth connection from earth electrode with 6 SWG dia G.L Wire in l5mm dia G.I. pipe from earth electrode, as required.
210
-
-
... More
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connection etc. As required.
66
-
-
... More
Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.
3
-
-
... More
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 1.5 sq. Mm
330
-
-
... More
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
-
-
-
... More
3½ X 25 sq. mm (28mm)
2
-
-
... More
3½ X 35 sq. mm (32mm)
2
-
-
... More
3½ X 95 sq. mm (38mm)
2
-
-
... More
3½ X 120 sq. mm (45mm)
2
-
-
... More
4 X 10 sq. mm (25mm)
20
-
-
... More
Supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials for following sizes of 3 core XLPE aluminum conductor cable of 11 KV grade as required.70 sq. mm
2
-
-
... More
(A)Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump).(B)Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainlesssteel shaft, mechanical confirming to IS : 1520.(C)Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.(D)M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.(E)Suitable cement concrete foundation duly plastered and with anti vibration pads-900 lpm at 35 m Head
1
-
-
... More
Providing and fixing IS marked butterfly valve (PN 1.6) rating with bronze/gun metal seat duty ISI marked complete with nuts,bolts,washers,gaskets confirming to IS 13095 of following sizes as required.
-
-
-
... More
80 mm diameter
1
-
-
... More
100 mm diameter
2
-
-
... More
Providing, installation, testing and commissioning of
non-return valve of following sizes confirming to IS:
5312 complete with rubber gasket, GI bolts, nuts,
washers etc.as required
-
-
-
... More
80 mm diameter
1
-
-
... More
100 mm diameter
1
-
-
... More
150 mm diameter
2
-
-
... More
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
1
-
-
... More
Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.-
-
-
-
... More
25 mm diameter
12
-
-
... More
80 mm diameter
60
-
-
... More
100 mm diameter
120
-
-
... More
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required-Single headed Gunmetal
6
-
-
... More
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585-20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.-40 m
4
-
-
... More
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required: Gun Metal
12
-
-
... More
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:-Gun metal
6
-
-
... More
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. For suitable dia MS pipe connection conforming to IS 904 as required-4 way - 150 mm dia M.S. Pipe
1
-
-
... More
Supplying installation testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.
60
-
-
... More
Supplying, installation, testing and commissioning of addressable horn cum strobe comple as required.
4
-
-
... More
Supplying, installation, testing and commissioning of addressable manual call Point complete as required.
4
-
-
... More
Supplying, installation, testing and commissioning of microprocess based intelligent addressable main fire alarm panel central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km,network communication card,minimum 320 characters graphics/LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM),power supply unit(230±5%,50 hz),48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger.The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/Digital voice evacuation system(which is part of the schedule of work under SH: PA system ) and shall be complete with all accessories,The panel shall be compatible for IBMS system with open protocol BACnet/Modbus over IP complete as per specification.-Two Loop Panel
1
-
-
... More
Providing and laying of 2x1.5 sq.mm. fire alarm armoured cable,600/1000V rated with annealed copper conductor having XLPE insulation,steel wire armouring & FRLS outer sheath complete as required.
250
-
-
... More
Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by
spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
84.24
-
-
... More
Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).
312
-
-
... More
Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 16 m
60
-
-
... More
Fine dressing of the ground.
3000
-
-
... More
Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
51
-
-
... More
Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge
51
-
-
... More
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to150 mm measured
5000
-
-
... More
Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge
500
-
-
... More
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)
520
-
-
... More
Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
80
-
-
... More
Providing and stacking of Polyalthia longifolia (Ashok) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.
100
-
-
... More
Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.
80
-
-
... More
Providing and stacking of Ficus bengalensis krishna of height 75-90 cm., multibranched in earthen pots of size 30 cm as per direction of the officer-in-charge
60
-
-
... More
Providing and Displaying plants Missbranthemum in different colour well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.
100
-
-
... More
Providing and Displaying plants Verbina in different colour having 30 to 45 cm ht., well developed with fresh & healthy foliage in bloom condition in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
100
-
-
... More
a) Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart)
1200
-
-
... More
Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42. For Terrace Pump
1
-
-
... More
Pressure Gauge Assemble with Gate/Ball Valve
2
-
-
... More
Air release Valve / Drain Valve
1
-
-
... More
MS Structure support for piping
150
-
-
... More
Providing and fixing 25 / 15 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)
6
-
-
... More
Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.
6
-
-
... More
Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)
12
-
-
... More
Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)
2
-
-
... More
Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)
2
-
-
... More
Supply, installation, testing & commissioning of 08 PASSENGER / 544 KG LIFT lift having contract speed of 1.5 MPS serving different floors in the lift shaft. Lift will be complete with combined luminous hall button with seven segment digital hall position indicator at all floor, car operating panel with luminous buttons, seven segment digital car position indicator combined with direction arrows, overload warning indicator, battery operated alarm bell and emergency light, fireman's switch at main lobby enclosed and as under:- I PRODUCT DETAILS Building Type-Government Education Inst, Lift Type-Passenger Lift, Rated Capacity Persons / Kgs-8 Persons / 544 Kgs, Rated Speed m/s-1.25, Number of stops / openings-4 / 4, Floor Designation-G+3, Access Sides Inline/Thru Type-1 (One), In Front Only, Floor Display Character (Entrance Position)- G (F),1 (F),2 (F),3 (F) II MACHINE AND CONTROLLER DETAILS Machine Location / Type-Directly Above The Lift Well –Gearless, Drive System-Micro Processor Based VVVF - Closed Loop, Control system-Microprocessor Based Duplex Selective Collective Control With / Without Attendant, Main Power Supply-AC 3 Phase, 50 Cycles, 415 Volts ±10%, Light Power Supply-220 Volts 50Hz LNE
III SHAFT DETAILS Shaft Type-RCC - Reinforced Cement Concrete, Shaft Width mm X Shaft Depth mm-1900 X 1900, Overhead mm-4200, Pit Depth mm-1600, Travel Height (in Meters)- 12, Shaft Reduction Channel-Not Required, Shaft Reduction Channel Weight (in Kgs)- No, Pit Ladder-Yes IV CABIN DETAILS A) SIZES Car Width mm X Car Depth mm-1300 X 1100, Car Clear Height mm-2200, Car Door Type Center/Side-Power Operated Centre Opening Sliding Door, No Of Door Panels-2 Panel, Type of Door Drive-Linear Door Drive System, Car Door (W X H) mm-800 X 2000 B) FINISHES - *SUBJECT TO AVAILABILITY Design Of Lift Cabin*-Stainless Steel, Lift Cabin Finish*-Honeycomb, Car Door*-Stainless Steel, Car Door Finish*-Honeycomb, Ceiling Finish*-Ss Hairline Finish, Ceiling Type-Premium Strip Ceiling-JLFC 04, Ceiling Light-Led Lights, Fan-Cross Flow – Fan, Flooring Type-Pergo, Handrail Type-Ss Round Handrail JLHR01, Handrail Location-Rear Side, Car Door Sill-Aluminum V LANDING DOORS DETAILS A) SIZES Door Type-Centre Opening Sliding Door, Door Size (W x H) mm, Door Sill-Aluminum, B) FINISHES Landing Door Finish*-1-4-Stainless Steel – Honeycomb, Landing Door Frame / Finish*-1-4-Stainless Steel – Honeycomb, Main Landing Floor-G, Other Landing Floors-1,2,3, Jamb Type-Slim Frame VI SIGNALIZATION / FIXTURES DETAILS A) CABIN OPERATING PANEL Car Operating Panel Type-Car Operating Panel - JLCP01, Number of Car Operating Panel-1, COP Faceplate Finish-Stainless Steel - Hairline Finish, Button Model-1s4 - Bas128 (Round), Car Display-Orange Square Dot-Matrix Scrolling Display-Vertical, Car Display Location, Car Operating Panel, Call Register Signal-Yes, Floor Annunciator-Yes B) LANDINGS INDICATORS Landing Operating Panel Type-Landing Operating Panel - JLLP01, LOP Location-Landing Display On Wall, LOP Mounting Type-Grouting, LOP Faceplate Material-Stainless Steel - Hairline Finish, Landing Display-1-4-OSDM-V, Landing Display Location-1-4-LOP, Call Register Signal-Yes, Stainless Steel Braille Button-Yes VII SAFETY DETAILS Over Speed Governor-Yes, Door Protection-Infra Red Door Screen, Counterweight Screen-Inbuilt, Over Load Indicator-Yes, Fireman Switch-Yes, Automatic Rescue Device-Yes, Battery Operated Emg Alarm Light-Yes, Two Way Intercom with Press & Speak in COP-Yes
1
-
-
... More
Providing and supplying desk-cum-bench (double seater) with an overall size 1050mm X 980mm X 750mm. The top of the desk shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on CRCA rectangle pipe having cross-section area 25mm X 25mm with 1.2mm thick. The shelf shall be made up of 18mm thick Pre-laminated particle board with 2mm thick PVC edge banding. It should be supported on CRCA rectangle pipe having cross-section area 25mm X 25mm with 1.2mm thick. The side panel of the table shall be made of CRCA rectangle pipe having cross-section area 40mm X 20mm with 1.2mm thick placed in vertical position at both side of the desk and bench. Hooks should be provided on the vertical side frame on both side of the desk for hanging bags/bottles. The front of the desk shall be clad with modesty panel made up of 18mm thick Pre-laminated particle board hinged with front pipe frame. The seat and back shall be made up of 18mm thick Pre-laminated particle board and the edges shall be sealed with 2mm thick PVC edge banding. The seat and back shall be supported on CRCA square pipe having cross-section area 25mm X 25mm with 1.2mm thick and 19mm X 19mm with 1.2mm thick respectively. 2 nos. footstep shall be provided for structural support of the desk having cross-section area of the pipe 40mm X 20mm with 1.2mm thick. The complete steel structure shall be welded with base pipe having cross-section area 40mm X 20mm with 1.2mm thick and also be epoxy polyester powder coated to the thickness 50-60µ thick. There shall be shoe provided at the base to avoid scratches as well as uneven surfacing. The size of the writing top shall be 1050mm(W) X 400mm(D), seat size shall be 1050mm(W) X 300mm(D), back size shall be 1050mm(W) X 200mm(H). All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.
484
-
-
... More
Overall size 3680mm L x 1540mm D x 900mm H made up of C-frame understructure. All sheet metal items shall be of CRCA as per IS 513:1994. C-frame made of rectangular pipe with cross section of 60mm x 30mm & 2 mm thick with feet tolerance of -5mm to +20mm & skirting at bottom side. Horizontal members to connect C frame shall be made of rectangular pipes of CRCA MS 2mm thick of pipe dimension 60 x 30 x 2 mm. Side cover panels, back panels should be made from CRCA MS panels of 1.0mm thick. Two 4' Fixed-Type CRCA MS Double Sided reagent shelves consisting of 2 stage horizontal storage shelves having 16 electrical switches 16A & 16 sockets 16A with 8 six module plates. Welded understorage cabinet with intersection of vertical and horizontal members having provision to be relocated anywhere easily as an independent unit. Doors should be assembled with hinge assembly. Intermediate horizontal channels should be provided between door and drawer. Shelf should be bend panel with 20mm height. single piece drawer tray supported on LH and RH ball slide to be provided. Knee space panel shall be in 22 gauge construction. 8 Understorages of Size 600mm W x 530mm D x 635mm H should be supplied. Four having 1 Drawer & 2 Shutters and Four having only 2 shutters. Thickness of storage unit LH/RH Panels, shutter front, bottom panel, Top front, drawer separator, alignement channel, Back panel, Shutter cover, Fr. Rack strip, top cover should be of 0.8mm thick. Handle polypropylene Recessed-Type. Lock facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit). Shutter should be of single-type construction. Ball Slide: 500mm Length (required only for drawer unit). Shutter should have provision of roller catch. Worktop should be 19mm (+/- 2mm) thick Black Granite worktop with exposed edges chamfered. Four S.S Sink of size 490mm x 405mm & depth 200mm. Bowl size 430 mm x 350mm. All steel frame-work is should be pre-treated with superior epoxy powder coated finish.The participating brand must have all the prevalent quality & safety related certifications like ISO:9001, ISO:50001, ISO:14001, ISO: 45001 , BIFMA, AIOTA for one or more product, Green Guard certificate for any one product atlest issued by UL of USA. The approved brands are Godrej, Geeken, Haworth, Steelcase & Merry fair only.
4
-
-
... More
Providing and Supplying of Revolving Stool, Should Have Minimum Approx. Height 510 Mm, Maximum Approx. Height 690mm Tubular Four Feet Base Of 25.4mm Od X 16g Thick Tube. Adjustment in Height By 25.4mm X 4 Tpi Accurately Machined Screw Is Covered With 38.1mm X 16g Vertical MS Round Tube Welded with Four Feet. Stool Should Have 300mm Dia. Cushioned Top. Stool Should Have Pvc Shoe with Nylon Reinforcement. Base Frame Should Be Epoxy Powder Coated. The Participating Brand Must Have All the Prevalent Quality & Safety Related Certifications Like Iso:9001, Iso:50001, Iso:14001, Iso 45001:2018, Bifma, Aiota For One Or More Product, Green Guard Certificate for Any One Product Atlest Issued by Ul of USA.
24
-
-
... More
Supplying and Placing Writing Board 1200mm x 3000mm Purpose : Writing Mounting type : Wall mounts Frame (All round framing) : With, Writing board placed Top Surface materials (Usedfor white board surface) : Porcelain Top surface material thickness : 0.7 mm to 0.8 mm Frame material :
Anodized extruded aluminum alloy hollow section conforming to IS 733
15
-
-
... More
Supplying & Placing Computer Desk of size 1200mm(W) X 600mm(D) X 750mm(H). It should have work top made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The desk shall be clad with 18mm thick modesty panel which provide structural support for the desk. It should be 18mm thick pre-laminated particle board connected with both end. At one side a fixed pedestal shall be provided with 3 drawer. The drawer shall be operated on roller channel and ball bearing channel to enable smooth operation. The drawer shall be operated with Al die cast handle with central locking mechanism in which all the drawers shall be locked with single key. Drawer facai, sides and all other shall be made in 18mm thick Pre-laminated particle board with appropriate edge banding and drawer base shall be 9mm thick. To protect the wall from kicks, abrasion and serve as a decorative moulding skirting shall be provided at bottom of the pedestal at both sides. The manufacturershall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The board used should meet international standards of quality and safety, Indian standard IS12823 grade II should meet long time loadbending, screw–withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.
15
-
-
... More
Supplying & Placing Conference table in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall have the size 1800mm X 1200mm made up of 2 nos. of 50mm thick pre-laminated particle board of grade II of IS 12823 with one side laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edgebander machine at 200 0C. The table top shall be supported by particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall have the size 1050mm X 695mm with 49mm thick and 100mm X 695mm with 18mm thick. The gable end shall be made up of Pre-laminated particle board with appropriate PVC edge banding and covered both side by Aluminium section. The table shall be clad with 18mm thick modesty panel which provide structural support for the desk. The modesty panel shall have an overall size 1200mm X 400mm with 18mm thick pre-laminated particle board connected with both end. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturershall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.
6
-
-
... More
Supplying & Placing three seater bench. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-60µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 440±10 mm(D) X 405±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm.
12
-
-
... More
Supplying & Placing executive table in completely knock down conditions with an overall size 1600mm X 1600mm X 750mm that is to be assembled at site. The worktop shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS powder coated rectangle pipe frame having cross-section area 40mm X 20mm. The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick with star perforation CRCA powder coated sheet in linear shape. The understructure shall consist of loop leg and C leg made up of MS powder coated triangular shape pipe having cross-section area 53mm X 53mm X 75mm. There shall be shoe provided to avoid scratches on the floor. Side top shall be provided with an overall size 800mm X 500mm X 750mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823. It shall be supported on peg which is mounted over side storage unit. The side storage having an overall size 1400mm X 570mm X 500mm. It should be made up of particle board with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 door shutter. The drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by handle and concealed crank hinge. Side storage unit shall be mounted on CRCA powder coated U shape leg having cross-section area 53mm X 53mm x 75mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.
10
-
-
... More
Supplying & Placing Visitor Chair. The seat and back shall be made of molded PU padded with high resilience polyurethane foam 40mm thick having density 40kg/m³ in seat and 25mm thick having density 32kg/m³ in back. The sae shall be upholstered with fabric tapestry 0.6mm thick. The seat and back shall be arrested together with the armrest. The frame structure shall be supported by four legs made up of MS/CRCA chrome plated pipe of size 30mmx15mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 465±10 mm(D) X 500±10 mm(W) and back size shall be 460±10 mm(W) X 360±10 mm(H) from seat. Overall height shall be = 790±10 mm, overall depth = 560±10 mm & overall width = 550±10mm.
20
-
-
... More
Supplying & Placing workstation table in completely knock down conditions with an overall size 4000mm X 1260mm X 1200mm that is to be assembled at site. The worktop shall be made up of back to back 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in sharing base rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported on particle board base gable end. The end wall of the top shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge banding. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in front side of user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) provided at front of the user. Laminated bottom tile shall be situated below the work top. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 4 nos. of drawer having same size. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 470mm X 286mm with 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.
1
-
-
... More
Providing and supplying mid back chair. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ with fabric tapestry 1mm thick and 300 GSM and the back shall be made of plastic inner upholstered with high resilience moulded polyurethane foam 25mm thick having density 32kg/m³ with fabric tapestry 1mm thick and 300 GSM. The back and base shall be supplied with injection moulded polypropylene outer cover. The armrest shall be used polypropylene loop arm completely joint with seat. For seating duranility the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle Dia. 650 mm fitted with 5 nos. twin wheel castors. The castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 455±10 mm(D) X 490±10 mm(W) and back size shall be 460±10 mm(W) X 450±10 mm(H) from seat. Overall height shall be = 880±10 mm, base width/ depth = 710±10 mm.
8
-
-
... More
Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of hot pressed commercial plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 35 GMS. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support with the assistance of cushion. The armrest shall be used cushion arm with leatherite covering top mounted on injection moulded ABS chrome holder. The frame structure shall be cantilever support type made up of MS/CRCA chrome plated rectangle pipe having cross-section area 30mm X 20mm with 2mm thick. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 510±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 520±10 mm(H) from seat & overall height = 955±10 mm, overall width = 650±10 mm & overall depth = 635±10 mm.
21
-
-
... More
Supplying & Placing Modular table in completely knock down conditions with an overall size 2650mm X 2200mm X 750mm that is to be assembled at site. The worktop shall have the size 2200mm X 1000mm x 76mm thick made up of Medium Density Fibre-board with approved veneer laminate and PU polish accordingly. The table top profile shall be in rectangle shape with round corners and full round post forming edges. The table top shall be supported on MDF board based gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 76mm thick medium density fibre-board and profile shall be in moulded construction with full round post forming edges and duly deco painted. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in linear shape with appropriate PVC edge banding and veneer laminate. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 2200mm x 600mm X 600mm. It shall have 2 nos. of drawer, 1 nos. of filling space with door and 1 nos of open space . The drawer shall be operated with profile handle and easily close & open with the assistance of sliding channels to enable smooth operation and sliding rail track and concealed crank hinge. Drawer facai, sides and all other shall be made in 18mm thick and drawer base shall be 9mm thick. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. The complete structure shall be supplied with approved veneer laminate, PU polish and deco painted. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.
1
-
-
... More
Providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (50+25)mm thick having density 40kg/m³ and the back shall be made of (15+6)mm thick double layered moulded plywood padded with high resilience polyurethane foam 40mm thick having density 32kg/m³. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine which helps to provide lumbar support as well as head support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used aluminium loop arm with polyurethane top completely joint with seat. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti-shock feature. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65±20mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged die cast aluminium having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(D) X 530±10 mm(W) and back size shall be 540±10 mm(W) X 750±10 mm(H) from seat. Overall height shall be = 1210±10 mm, overall depth = 630±10 mm & overall width = 650±10 mm.
1
-
-
... More
Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of hot pressed commercial plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 35 GMS. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support with the assistance of cushion. The armrest shall be used cushion arm with leatherite covering top mounted on injection moulded ABS chrome holder. The frame structure shall be cantilever support type made up of MS/CRCA chrome plated rectangle pipe having cross-section area 30mm X 20mm with 2mm thick. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 510±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 520±10 mm(H) from seat & overall height = 955±10 mm, overall width = 650±10 mm & overall depth = 635±10 mm.
6
-
-
... More
Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leatherite tapestry 1±0.2 mm thick. The understructure shall consist of Powder Coated reducing type legs having dia 25-20mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 530±10 mm(D) X 1600±10 mm(W), seat height = 430±10 mm, overall width = 1950±10 mm, overall depth = 800±10 mm & overall height = 840±10 mm.
1
-
-
... More
Supplying & placing center table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 12mm thick toughened glass. The top profile shall be in rectangle shape with bevelled edges. The understructure shall consist of MS/CRCA rectangle pipe frame having cross-section area 30mm X 15mm with 1.6mm thick duly powder coated with 40-60µ dy film thickness.
1
-
-
... More
Supplying & placing Back storage unit with an overall size 2250mm X 450mm X 2200mm. It should be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade with extruded Aluminium profile. All profile i.e. side, back, shutter, shelf, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The storage shall have shelves and 8 nos. of door shutter for ease of opening. The shutter shall be operated with concealed crank hinge and die cast handle. There shall be legs provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.
1
-
-
... More
Providing, supplying and placing steel Almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The cabinet shall be supplied with 2 nos. of doors and 4 nos. of adjustable shelves. The doors shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom of the Almirah. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-60µ thick.
25
-
-
... More
Providing, supplying and placing Aquagurd water purifier with inbuilt water cooler. Type of water purification technology shall be RO+UV+CuZn. Power consumptions of system (with ± 5% tolerance) (in watt) 775. Maximum Input Water TDS allow to the system shall be 2000. Operetion mode Fully automatic with auto cut off. Storage tank capacity up to float valve level (in liter) shall be 120 ltrs. RO Membrane rating shall be 80 GPD. RO Membrane Auto flush at every start,every stop and every one hour for 1 minutes. Feature required in this machine-Ultraviolet (UV) LAMP, Arsenic removal, Fluoride removal, Chloride removal. Material of water Storage Tank shall have Stainless Steel SS 304. Particulate Filter size 20 inch, Particulate Filter Porosity 5 micron. Activated Carbon filter Size 10 Inch. Minimum inlet pressure 1 KG/CM2. should have high pressure pump. Filteration water capacity in liter/ hour 50 ltrs. TDS removal percentage from RO Membrane 90%. Body of filter ABS Food grade. Number of candles 6 or more. Three Number of Water Faucets. Cooling capacity at comfort level (17 ± 1 degree celsius) (in liter per hour) 80 ltrs. Warrenty period 1 years.
5
-
-
... More
Lift Panel : The panel includes 415V, 100A, 3Ph, 35kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character: Incomer 1 No. 63A/FP/ MCB Bus bar -100A, 16kA AL Outgoing 40A ,4P, 30mA RCCB- 1 no 40Amps, TPN, MCB -1 no 16 Amps, DP MCB -1 no 16 Amps, DP RCCB -1 no.
1
-
-
... More
Roof Top SPV Power Plant : Design, manufacture, supply, testing & commissioning of grid connected 40 kWp Solar Rooftop Power Plant without Battery backup including 05(five) years comprehensive maintenance contract on turnkey basis.
10
-
-
... More
Cable Trunking System heavy duty as per ISI: 14927(Part-1):2001 marked: Supply and fixing of heavy duty cable trunking system as per ISI: 14927(Part-1):2001 "CM/L number must be declare" i.e should be high protection aganist solar, heavy mechanical stresses, insulating material & flame propagating trunking system. Access cover retention of the system. Size W38 mm x D 16mm, L =2.0m
810
-
-
... More
100 kVA TRANSFORMER AS PER IS:1180:- Supply, fitting, fixing, commissioning and testing of 100 kVA , 11 or 6.6 kV/0.433 kV Sealed ,Deta/Star, vector group DYn11, outdoor, Oil Cooled Type ONAN off circuit Star Rating Transformer with copper wound Transformer and civil foundation work as per the norms 100 kVA outdoor transformer with all accessories as per IS- 1180 of 2014, air filled cable box suitable for 11kV or 6.6 kV , 3C 35 sqmm XLPE Al. armoured cable for 1.1kV, 3.5Cx150sqmm XLPE Al. armoured cable as required. ( Make:-ABB/Voltam/ GTB/ Kirloskar / Bharat Bijlee)Apart- from the above standard fittings followings items should be included:- Capacity- 100 kVA Installation - outdoor No. of phase-Three Voltage 11kV/433V, Vectro Group -DYn11, Duty- Continuous, Tapping in primary-+/- 5% to -10% in 2.5 steps, Cooling - ONAN, Insulation class-A, Temp. rise @ 50 Deg. C. Ambient , Oil by Thermo Meter :- 50 Degree C. , In winding by Resistance :- 55 Degree C. all complete with stand foundation and installation as per engineer in charge.
1
-
-
... More
HT Cable 3Cx35 sqmm(UE):- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 11kV (UE)grade
130
-
-
... More
Solar LED Standalone Street Light( 45W LED) with low maintenance lead acid battery for 3 day backup: A LED based solar street lighting system consisting of PV modules, electronics ,lead acid battery, and LED based luminaries all suitably mounted on a 6.0m tubular pole above ground , base plate etc as required included . The battery is charged by electricty generated through the PV module panel (180 i.e 90x2 )during day time and the luminaries provides light from dusk to dawn. Specification of of solar LED Standalone street Light: Supply, installation, testing and commissioning of Poly crystalline silicon solar panels, High lumen LED for max. efficiency with lifetime 50,000 hrs CRI nominal 70. Pressure die cast aluminium IP66 enclosure. Controller to charge batteries & microcontroller for autonomously determination of sunrise & sunset. Specific deep discharge batteries are used to store the energy. Metal battery box to be fitted at 5.0m steel tubular pole( Modle-Havells).
1
-
-
... More
Chemical Earthing : Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) Each chemical earthing shall have following details:- Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed). Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton)
8
-
-
... More
Main LT Panel for New class room+campus : The panel includes 415V, 200A, 3Ph, 25kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character: Incomer 1 No. 160A/FP/ 25kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. 1 no-160A , FP MCCB(25kA) for DG incomer Electro-mechnical lock for auto changeover -1 set: 160A, 4P Bus bar -200A, 25kA AL 3 phase kWh meter-1 no Outgoing 1 No, 100A/FP/25kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links. ( for feeder pillar at Science campus) 7 nos-63A , 4P, MCB for feeder pillar+ lift panel (new class room)+ floor PDBs of (new class room)+spare 10 nos- 40A /60 , DP, MCB , 10kA for different buildings
1
-
-
... More
Outdoor Feeder Panel (located main campus): Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of suitable size ,earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. All inter connections shall be made with 2.5, 4 , 6 Sq mm PVC Cu. wire. The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs Incomer : 1 No. 63A/FP/ 10kA/ MCB . 0-24hrs Timer switch with bypass arrangement, 40A Duty contactor Outgoings: MCB 40 A, TPN, 10kA-1 no for highmast or spare and MCB 20 A, TPN, 10kA - 4 nos for street light 100 amp 415 V heavy duty three phase with neutral busbar chamber Indicator switch, selector switches etc
2
-
-
... More
Outdoor Feeder Panel (for Science campus): Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of suitable size ,earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. All inter connections shall be made with 2.5, 4 , 6 Sq mm PVC Cu. wire. The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs Incomer : 1 No. 100A/FP/ 16kA/ MCCB . Outgoings: 3 nos-MCB 63 A, TPN, 10kA-1 no for power DBs of Science Building+ lift panel 5 nos- MCB 40 A, SPN, 10kA-for LDBs-science building MCB 20 A, TPN, 10kA - 2 nos for street light 100 amp 415 V heavy duty three phase with neutral busbar chamber
1
-
-
... More
Add 18% GST
18
-
-
... More
Add 1% Labour cess 1%
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements