Rural Works Department Tender
Search from across the categories, cities, and authorities to find the latest Jharkhand tenders. Every Jharkhand tender is curated from credible sources of government websites (eProcurement Jharkhand portal) and newspapers, thus ensuring the credibility of the information presented to you. For more information on Jharkhand tender bidder registration, the login process and more read the FAQs section on this page.
Costs
EMD
₹ 5,98,000Document Cost
₹ 10,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_RWD_85442_1Bid Award Id
ViewTender No
19/2023-24/RWD/SIMDEGATender Authority
Rural Works Department ViewPurchaser Address
-Website
http://jharkhandtenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Construction of Embankment with Material Deposited from Roadway Cutting (Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300-2.) Rate per cum after adding royalty @Rs 27.48/cum
352.4
21665
61.48
Granular Sub-Base with Coarse Graded Material (Table:- 400- 1) Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. With Grading-I Material S.O.R. Item No. 4.01 B (i)
1825.26
4602028
2521.3
Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. S.O.R. Item No. 4.14 A
1233.64
3501588
2838.42
Prime Coat over WMM/WBM (Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.) S.O.R. Item No. 5.01 A (i
7907.92
650821
82.3
Tack Coat on Granular surfaces treated with primer Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. S.O.R. Item No. 5.02 (ii)
7907.92
128978
16.31
Tack Coat on Bituminous surfaces Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.
7907.92
104147
13.17
Bituminous Macadam Grading-II with VG-30 Grade Packed Bitumen (Providing and laying bituminous macadam with higher capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction.) RCD S.O.R. Item No. 5.03 (ii)
395.4
3494410
8837.66
Semi-Dense Bituminous Concrete (Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 508 complete in all respects.) for Grading-II (10 mm nominal size) S.O.R. Item No. 5.7(MORT&H 4TH)
197.7
2244488
11353
Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing
842.27
5420159
6435.18
Reinforced cement concrete M15 grade Ordinary kilometre stone (precast) stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703.S.O.R Item no 10.10 (ii)
4
6963
1740.9
Retro-reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)
1
7526
7526
Direction and Place Identification signs with size more than 0.9 sqm size board (Providing and erecting direction and place identification retro- reflectorised sign asper IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)
0.81
11658
14393.1
Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. S.O.R. Item No. 8.13
417.58
243991
584.3
E/W in excavation for structure as per drawing and technical specification clause 305.1 including setting out, construction of shoring and brading, removal of stumps and other deleterious material and disposal utp a lead of 50m, dressing of sides and bottom backfilling in trenches with excavated suitable material. (with manual means in ordinary soil & Depth upto 3m) S.o.r item no 3.13(i)A
378.06
21095
55.8
Plain/reinforced cement concrete in fdn complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204.S.o.r item no13.5 A
(P.C.C. Grade M-15 )
56.28
270955
4814.42
Stone masonry work in cement mortar 1:3 in foundation complete as per drawing and technical specifications.square rubble coursed rubble masonry(1st short).
208.47
979848
4700.19
Stone masonry work in cement mortar 1:3 for substructure complete as per drawing and technical specifications.coarsed rubble masonry in sub structure.
60.04
290884
4844.84
Laying Reinforced cement concrete pipe NP4 / prestressed concrete pipe(1000mm)for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets .
22.5
176076
7825.62
Plastering with cement mortar (1:3) 15 mm thick on brickwork in parapet as per technical specifications Clauses 613.4 and 1208.4S.o.r item no13.3
204.84
22651
110.58
Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204.S.o.r item no13.5 A
(P.C.C. Grade M-15 in Coping)
4.13
19849
4806.22
Dry Rubble Flooring. (Construction of dry rubble flooring at cross drainage works for relatively less important works.)
29.73
71787
2414.66
Plain/Reinforced cement concrete in sub-strucutre complete as per drawing and Technical speciofications(pcc grade m-25 in deck slab)
11.73
67099
5720.32
Supplying, fitting and placing HYSD bar reinforcement in sub structure complete as per drawing and technical specifications
1.82
160691
88243.34
Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces
141.62
9955
70.3
Plain/Reinforced cement concrete in sub-strucutre complete as per drawing and Technical specifications.(PCC grade m20 in s/s)
10.08
52923
5250.37
Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications
4.89
58703
12004.84
Providing & fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing & Technical Specification.
45
12100
268.9
Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 S.o.r item no13.8
60
6630
110.5
Back filling behind abutment, wing wall, return wall complete as per drawing and technical specifications
40.8
46625
1142.78
Goods & Service Tax (G.S.T.) -
24785604.12
4461408
0.18
Labour Cess -
29247012.86
292470
0.01
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements