Rural Works Department Tender

Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Technical Specification Clause 302.3

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1.

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a 50 m lead as per Technical Specification Clause 301.5

Construction of granular sub-base For Grading III Material by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Providing, laying, spreading and compacting stone aggregates (WBM Gr. - II) of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405. By Mechanical Means.

Providing, laying, spreading and compacting stone aggregates (WBM Gr. - III) of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. By Mechanical Means.

Providing & laying 50mm thick built up spray grout over WBM Surface including cleaning the surface heating bitumen to required temperature applying primer and tack coat @ 10 kg/ 10M2 and also including cost of bitumen and stone aggregates conforming to physical properties & grading given in the MOST table 500-7(3rd revision) spreading stone metal @ 0.66 cum per 10 M2 in laying, hand packing rolling compacting & then applying spray of bitumen @ 15 kg/ 10 M2 finishing with key aggregates 0.13 cum/10 M2 in proper grade camber of super elevation and rolling the same with road roller and finishing the surface with template including the cost of barriers, danger signal, chowkidar, making and maintaining diversion including cost of all labours cost of POL and all other lubricants & also hire charges of road roller with depreciation & major repair all complete job as per specification and direction of E/I.

Providing 50mm thick compacted built up spray grout over old bituminous surface in grade camber of super elevation with stone aggregates and key aggregates @ 0.66 cum and 0.13 cum per 10 M and as per MOST table 500-7 and bitumen 20kg including tack coat all per 10 M2 including cost of heating bitumen to required temperature applying tack coat @ 10kg/10M2 and also including cost of bitumen and stone aggregates conforming to physical properties & grading given in the MOST table 500-7(3rd revision) spreading stone metal @ 0.66 cum per 10 M2 in laying, hand packing rolling compacting & then applying spray of bitumen @ 15kg / 10 M2 finishing with key aggregates 0.13cum/ 10 M2 in proper grade camber of super elevation and rolling the same with road roller and finishing the surface with template including the cost of barriers, danger signal, chowkidar, making and maintaining diversion including cost of all labours cost of POL and all other lubricants & also hire charges of road roller with depreciation & major repair all complete job as per specification and direction of E/I.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. By Manual Means Bitumen (S-65).

Providing and laying seal coat Type - 'A' sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A as per Technical Specification Clause 510, Bitumen (S-65).

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,

Reinforced cement concrete M15 grade 5th Kilometre Stone (precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

Reinforced cement concrete M15 grade Ordinary Kilometer Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

Reinforced cement concrete M15 grade 200 m stone (precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704

Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701

Providing and erecting direction and place identifications of semi reflective sign boards as per IRC:67 made of 2 mm thick M.S. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour. Supported and welded on 47 mm x 47mm of 12 SWG Square tube of 3050 mm height duly strengthened by 25 mm x 5 mm M/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Goods & Service Tax (G.S.T.) -

Labour Cess -