Rural Development Department Tender

EPOXY WORK Providing Epoxy flooring self leveling type on strong base in desired colour/design as approved by Engineer-in-Charge. Resin for epoxy is to be of floor grade type i/c appropriate hardner and filler material. with 5 year defect liability period.3 mm thick

MISCELLANEOUS WORK DOOR WORK Hermetically Sealed Sliding Door System: Fabrication, Supply, installation, testing & commissioning of sliding type Hermetically Sealed door having high density particle board cores/ CFC free Polyurethane, high pressure laminate face on both sides, viewing window 300 x 300mm. Size: 1500 x 2100 mm (W x H) as per direction of EIC. Automatic Doors: Provided with Radar Switch - 2 Nos., Foot Switch - 2 Nos. and Photocell Sensors. Automatic Door (1500 mm x 2100 mm) Approved makes - Metaflex /REBBON / MDD Engineering/ Altos / Dormed/ Meditech

HOSPITAL FURNITURE WORK Revolving Chair With Arm Synchronic tilt mechanism (GODREJ INTERIO ACE FULL BACK CHAIR) (Product id: 5116877-95084053146)

OCEAN LIFE SCIENCE CORPORATION Laboratory Steel Furniture Side bench with rack and table top OCEAN LIFE SCIENCE CORPORATIONR (OLSC-IWB)

BETCO Laboratory Steel Furniture Island bench with table top BETCOR (BETCO-LB-202)

EFFLUENT TREATMENT PLANT (ETP) - CAPACITY 2 KLD Supplying, installation, testing & commissioning of Effluent Treatment Plant for the following duty: Nature of waste water - Lab effluent Daily Avg. Flow = 2 cum/Day Reuse of ETP treated water after treatment. Horticulture, Landscaping, irrigation etc. Influent Characteristics (considered) pH - 6.5-8.0, BOD5- 200-250 mg/liter,S. Solids - 250-300 mg/liter, COD- 400- 600 mg/liter, Oil & Grease-50 mg/liter, Effluent discharge standard after treatment:, p - 6.5 - 8.0, BOD5- Less than 30 mg/liter, S. Solids - Less than 50 mg/liter, COD- Less than 100 mg/liter, Oil & Grease- 5 mg/lt, Supply, installation, testing & commissioning of Screens Mild Steel Suitable Sized Manually operated Bar Screen as per following specifications. (1nos), Cleaning :- Manual Screen, MOC :- MS Supply, installation, testing & commissioning of Raw effluent lifting pumps complete with all accessories, motor of required capacity. Pumps shall have following duty: (1 lot) Flow rate (each) = 0.25 m3/hr,Head= 8-10 m, Make = Kirloskar/Wilo/Eqv. Supply, installation testing and commisioning of physico-chemical treatment, the system shall be comprising of dosing pump, dosing tank, and Agitators.( 1 lot), Dosing Units Alum Dosing system, Poly Dosing System,Lime Dosing System, Tube deck media in settling tank Providing and fixing all interconnecting plant piping of required MOC as MS/UPVC and isolation control valves for making the piping arrangement complete within the battery limits.(1 Lot) Supply, installation, testing & commissioning of SBR feed Pumps with CI casing & CI impeller complete with all accessories, motor of required capacity. The pumps shall be complete with all accessories. Pumps shall have following duty: ( 2 Nos), Flow rate (each) = 0.25m³/hr Head= 8-10 m, Make = WILO/Kirloskar/Eqv., Supply, installation, testing & commissioning of SBR Based Biological system comprising of the following equipments: (1 Lot) Air Blowers For SBR tanks, Capacity :Apprx. 5-10 m3/hr. @5000-5500 mmwg,Type Twin Lobe, Fine Bubble Diffusers, Qty: 1 Lot, Decanter ( 1Nos), Make: PS aqua/ Grannus Water and Env. Solution Pvt. Ltd., Pipes and fittings for Air piping and Air Grid (1 Lot), Supplying, installing, testing, commissioning of Centrifugal Horizontal Filter Feed pumps Complete in CI body & CI impeller with motor, and all other accessories required to complete the system.(2 Nos.), Pumps = 02 Nos.(1w + 1s), Flow rate (each) = 0.25 m³/hr, Head = 25 - 30 m, Make - Kirloskar/Eqv, Supply, installation, testing & commissioning of Sludge transfer/feed pumps for sludge transfer to SHT complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line. (1 Lot), Flow rate (each) = 0.5/1.0 m³/hr, Head = 8-10 m Make - Kirloskar/Eqv, Supplying, Installation, testing and commissioning of Chemical dosing system comprising of Sintex Tank with inlet/ outlet connection, piping and valves along with metering pump for dosing. ( 1 Set), Supplying, installing, testing, commissioning of Sludge Bag System of suitable size for the dewatering of sludge generated per day.(1 Set), Make: Grannus Water and Env.Solution Pvt. Ltd., Mode of operation: Manual, Supplying, installation, testing & commissioning of FRP vessel filter with frontal piping and Valves with all the required accessories. Filter shall include media, standard fittings like pressure gauges, sampling cock, rinse drain., Dual Media Filter ( 1 Nos), Dia : 150 mm , HOS: 1100, Filter media: Fine and coarse sand, pebbles and gravels, Make: PS aqua/ Grannus Water and Env.Solution Pvt. Ltd. ELECTRICAL PANEL AND ACCESSORIES Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor control centre fabricated out of 14 gauge CRCA sheet steel. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of red oxide primer and final approved shade of powder coated paint. 2 Nos. earthling terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system. Panel should be complete with Isolation push button for every equipment and auto manual selection switches . Make: GWESPL/Eqv Cost for above work (A) ( In Rs.)

Tanks Supply, installation. Testing and commissioning of following Tanks In MSEP/HDPE Flash Mixer Flocculation tank Settling Tank Break Tank SBR Tank

Double Skinned Floor Mounted Air Handling Units with Pre & Fine Filter Supply, installation, testing and commissioning of factory fabricated Double Skinned Air- handling unit celing Suspended type / Floor Mounted Factory fabricated out of extruded aluminium section consisting with 0.8 mm pre-plasticized/pre-coated Galvanised steel sheet outside & 0.8 mm plain alvanised steel sheet with 40 mm thick injected PUF of density not less than 38 Kg/CuM. 6 Row cooling coil made of Aluminium finned Copper tube ( thickness 0.50 mm) with coil section, pre - filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% (MERV 8), & Fine- filter section with non woven synthetic media of 3 micron particle size with an efficiency of 95% (MERV 13), section with multirows 6 Row deep DX cooling / heating coil of copper tube & aluminium fin construction, Motor fan section complete with floor standing forward curved DIDW centrifugal fan, squirrel cage induction motor, belt drive package, sanwitch Insulated stainless steel drain pan and vibration isolation pads all complete as per specifications. AHUs shall be selected for a maximum face velocity of 500 FPM. The units shall be compatible with VRF outdoor units. The unit shall be supplied with inbuilt DOL starter for motor, electronic expansion valve/s (Dx), thermostats, control wiring & all accessories as required for completing installation. Fan outlet velocity shall not exceed 1653 FPM (8.4 MPS). Fans for emergency application Tube axial are to be used.Sound level for emergency operation it should not exceed 88 Db(A)@ 3 meter (Room condition).Incase of not achieving sound , attenutor has to be added.Outlet velocity of the fans should not exceed (For AHU No. Please Refer Basic Of Design & AC Tender Drawing ) AHU / LAB - 2 x 8.5 TR Air Cooled Condenser Outdoor Unit

for Supply Fan , 4850 CFM Ex. Blower , 75 mm Static Pressure 4300 CFM Supply Blower, 6 Row CC, 125 mm Static , Pressure for Exhaust fan ) Supply Installation, testing & commissioning of Air Cooled Ductable Split Units. - Outdoor & Indoor unit shall connected with DX coil, refrigerant piping, firstcharge of refrigerant & oil, HP/LP cutout, thermostatic expansion valve, distributor, starter and other necessary controls to form a factory tested compact unit. The outdoor unit shall have condenser coil, fans with motor & drive, copleand scroll compressors, panel etc. The ductable units should be complete with programable microprocessor panel (BMS Compatible). ( Make: LG / Blue Star / Daikin) 8.5 TR With Scroll Compessor

Supply, installation, testing and commissioning of factory fabricated Double Skinned Fan Filter Unit Celing Suspended type Fabricated out of extruded aluminium section consisting with 0.8 mm pre-plasticized/pre-coated Galvanised steel sheet outside & 0.8 mm plain alvanised steel sheet with 40 mm thick injected PUF of density not less than 38 Kg/CuM. Hepa - filter section with non woven synthetic media of 1 micron particle size with an efficiency of 99.99% (MERV 20) with Motor fan section complete with floor standing forward curved DIDW centrifugal fan, squirrel cage induction motor, belt drive package, As per specifications. AHUs shall be selected for a maximum face velocity of 200 FPM. & all accessories as required for completing installation. Fan outlet velocity shall not exceed 1653 FPM (8.4 MPS). FFU - 640 CFM with Hepa Filter, 40 MM of WC

FFU - 780 CFM with Hepa Filter, 40 MM of WC

FFU - 1300 CFM with Hepa Filter, 40 MM of WC

Supply,installation and testing of powder coated aluminium extruded grills/diffusers as per specifications given in tender and of following sizes: Single Louvered supply / Return Air registers (Grill)

Supply / return suare ceiling air terminals (diffusers)

Fresh / Exhaust air louvers with bird screen & damper

Flexible connection for AHU/FCU madeup of f/r fabric compelte with flange

Supply,installation and testing of multiblade type GI Duct Damper for duct/collars to be provided with suitable links and quadrants for control of volume of air

Supply and Application of Acoustic Insulation Inside the Duct with Engineered Nitrile Rubber open cell foam with Density 140 - 180 Kg/m3 passing Class 1 Fire Performance test as per BS 476 Part 7, Air Erosion test for 10,000 fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection. The material should pass Fungi Resistance Test as per DIN EN ISO 846 Method A and Bacterial Resistance Test as per DIN EN ISO 846 Method C; to be applied using manufacturer's recommended Rubber based Adhesive in a blend of solvents.conforming to standard specification. 15 mm thick open cell nitrile rubber.

Supply & Installation of Thermal Insulation on Ducts not exposed to sunlight using Closed Cell Class O Nitrile Rubber Elastomeric Insulation of Density 40 - 60 Kg/m3, Thermal Conductivity of 0.037 W/mk at 20 Celcius Mean Temp. and µ≥7000 (without any additional vapour barrier) and with factory laminated aluminium foil of minimum 60 Microns thickness having weight of 193 gsm as per EN ISO 2286-2, tensile strength shall be 90N/15mm as per EN ISO 527-3 with elongation 10% as per EN ISO 527-3; to be applied on Ducts using manufacturer's recommended Rubber based Adhesive in a blend of Solvents.25 mm thick (Class O) Foil for Supply Air Duct

MOTOR CONTROL CENTRE

i) For 2 x 8.5TR Outdoor Unit Supply, installation, testing and commissioning of Cubical type sectinalised floor standing switch board of 31 MVA fault capacity at 415 V complete with 4 strip, 63 A capacity Aluminium Bus - Bar Electrolytic grade, cable alley, switchgears of following capacity & as per specifications. i) INCOMER 01 Set - 63 A manually operated draw out type TPN MCCB with Overload, short ckt., earth fault, protection release, with 144 mm (0 - 63 A) ammeter protection release, with 144 mm (0 - 63 A) Voltmeter with selector switch, phase indication light with protection fuse, on / off / trip indicating light . OUTGOINGS i) For 02 Nos. Outdoor Unit 02 No. - 40 A TPN MCB with overload, protection with (0 - 40A) ammeter with three CT & selector switch, on / off / trip indication light with protection fuses. Controls & interlocking accessories as required. LOT Power Cabling (PVC insulated and PVC sheathed, armoured, Aluminium Conductor of 1.1 KV grade of following sizes. i) For Compressor 3C x 10 Sq. mm Aluminium Conductor

ii) For Indoor Unit Blower & Compressor 3C x 4 Sq. mm Aluminium Conductor

iii) For Condenser Fan 2C x 1.5 Sq. mm Copper Conductor

Control Cabling ( PVC insulated & PVC sheathed, armoured, Copper Conductor of 1.1 KV grade of following sizes. 6C x 1.5 Sq. mm Copper Conductor

Supply & laying of 8 SWG GI wire.

GST @ 18%

Labour cess @ 1%