Road Construction Department Tender

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) SECTION (39.40X17.70X1.5)mm - @ 0.65Kg/m

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

S/F/F 4mm Thick ACP Board in aluminium door, window, ventilator shutters and partitions etc.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Labour for fitting and fixing G.C.I. or C.A. sheet roofing in NAM proper slope including the cost of "J" or "L" hooks, limpet and bitumen washers, carriage of sheets to work site, and taxes all complete as per building specification and direction of E/I.

Supply of G.C.1. Sheet thickness in mm (i) 0.80

Supplying, fitting & fixing M.S. Grill made of 20x6mm flat as per approved design and drawing aproperly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over steel surface including preparing the surface after cleaning removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification direction of E/I.

Providing 2 coats of Synthetic Enamel Paint of approved shade and make over steel surface grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.

Providing one coat of painting with ready mixed paint of approved shade and make over old wooden surface including cleaning the surface after Removing dirt including scales As per specification and direction of E/I.

hp Intel Core i5 All in One PC with 23.8 Inch Display/ Windows 11 Professional hp (HP 440 G9 AIO i5 12500 Win11P 8512SSD3 wifi 23.8")

ARIHANT FUR Executive Table with Both side pedestal unit ARIHANT FURR (OFFICE TABLE BIG)

FLOYD Executive Table with One side pedestal unit and E.R.U FLOYDR (FXO/09

xerox Multifunction Machines Mfm, On Site OEM Warranty 1 Year xeroxR (Xerox Versalink B7125 (25 PPM, Mono) + WiFi + 1TB HDD with 1 Year Warranty)

C3 Revolving Chair with Revolving with back tilting C3R (CFPL-NP-J HIGH BACK CHAIR) Type of chair High Back Tilt mechanism Revolving with back tilting Locking mechanism Back tilt and locking Seat depth adjustment Fixed type Revolving mechanism Designed with 360 degree-revolving type Pedestal base Mild steel chrome plated Minimum thickness (in mm) of MS Plate Joining the backrest with seat of the chair 2 millimeter

Elentra Furniture Revolving Chair with Synchronic tilt mechanism Elentra FurnitureR (Revolving Chair)

GODREJ INTERIO 3 Seater Public Place Seating Chair of M S ERW tube with arm and backrest WITHOUT CUSHION GODREJ INTERIOR (GODREJ INTERIO WAITING CHAIR – 3 SEATER WITH COMMON ARM (135-136))

Unbranded--ALLOY WORLD Legs Office Chair Non-revolving and non-tilting chair with armrest Unbranded Manufactured by: ALLOY WORLD (Office Chair JS)

Canon Laser Mono Computer Printers for A4 paper size CanonR (Canon LBP6030w - Standard Warranty)

GODREJ INTERIO Almirah Steel shelving cabinet with partial wardrobe GODREJ INTERIOR (GODREJ INTERIO APO STORWEL PLAIN)

microtek Line Interactive UPS with AVR of Rating 0.65 KVA With Warranty of 2 Years microtekR (Legend 650)

Supplying Split Type AC with installation and complete acessories with all taxes and royalty all complete as per E/I. CATEGORY "A" (Daikin Hitachi, L.G., Voltas or equi.) 1.5 Tr. 5 Star Split A.C (lnverter Type) IS- 1391-part-I

Supplying Split Type AC with installation and complete acessories with all taxes and royalty all complete as per E/I. CATEGORY "A" (Daikin Hitachi, L.G., Voltas or equi.) 2.0 Tr. 5 Star Split A.C (lnverter Type) IS- 1391-part-I

Supplying Copper Tube with installation and complete acessories with all taxes and royalty all complete as per E/I. Copper Tube of size 5/8" for split AC unit 1/1.5/2/3 tr capacity including nitride rubber insulation

Supplying Drain Pipe with installation and complete acessories with all taxes and royalty all complete as per E/I. Drain Pipe for AC

Supply of Ceiling ceilins fan 48" (1200mm)

450 mm (18") metal body wall fan with speed regulator suitable for sfuncle phase 220Y,50H2 AC supply

LED tube with Batten 20W: Supply, installation, testing and commissionof wall mounted LED 20W tube light suitable for 230V, single phase supply voltage, with all accessories like batten and electronic driver complete as required.

Surface mounted round Downlightes 6W/7W LED: Supply and installation of round shapeed surface mounting downlight for common area, toilets.

LED Flood Light 100W:Supply installation Testing and Commissioning of LED flood lighting( 100W ) luminarie with prssure die cast housing and toughened glass cover (IP-66 protection in existing pole/ pipe for supply voltage 100-270 volts AC, 50Hz. Luminarie shall confirming to IS:10322 part-5/ section -5 and shall be conecessary accessories as per required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Bell push

AQUA INTERNATIONAL Potable water purification system with inbuilt water cooler. UV AQUA INTERNATIONALR (AI WC 60/80/150 (UV))

Sony Type/Category/Class of TV set Smart TV(2) Actual Screen Size (inches) 50 LED (Light Emitting Diode) SonyR (KD-50X70L)

Supplying and fixing male ended 15 mm dia brass bib cock of approved quality (wt. not less than 350 grms) with extra socket all complete as per specification and direction of E/I.

Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I.(A) BRASS STOP COCK 15 mm dia

Providing and fixing Gun metal full way valve of approved quality, all complete, as per specification and direction of E/I. 32 mm and weight not less than 700 gms.

Providing and fixing Gun metal full way valve of approved quality, all complete, as per specification and direction of E/I. 40 mm and weight not less than 1.0 kg.

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I. "P" trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings C.I. or C..C. brackets 32 mm alkathene/ PVC telescope flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. with 12.5 lit. low level PVC cistern

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm PVC waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Providing and fixing on wall face unplasticied Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion (i) Single socketed pipes 75 mm

Providing and fixing on wall face unplasticied Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion (i) Single socketed pipes 110 mm

Supplying fitting and fixing white glazed fire's clay sink of approved make with overflow arrangements supported on C.I. Or R.S. Painted bracket 40mm. Dia C.P. Brass waste with C.P. Brass chain and rubber plug 40mm dia P.V.C. Waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams including cutting wall and making good the same etc. all complete as per specification and direction of E/I.(iii) Lab sink of size 450 mm X 300 mm X 150 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge External work 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge External work 40 mm nominal outer dia Pipes

Providing and fixing PTMT grating of approved quality and colour. Circular type - 100 mm nominal di 125 mm nominal dia with 25 mm waste hole

Special type C.P. Bath room Fitting for V.I.P.Buildings- Jaquar, Towel ring

Special type C.P. Bath room Fitting for V.I.P.Buildings- Jaquar, bib cock long thread

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I. Mirrors of 6mm thick glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror600mm x 450mm size

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.C.P. brass dish container medium quality with screw and hinges etc.

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(a) From 0.00 M to 50.00 M below G.L.

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(b) From 51.0 M upto 150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914. F.A.S.D starter upto 5 H.P

3 core PVC insulated PVC sheathed copper conductor flat submersible cable. Supplying , Flat flexible submersible cable with ,copper conductor , PVC insulated and PVC sheathed as IS:7098-- 3 Core 4 Sq mm

Supply fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quaility as per IS:1239 ( part 01 ) 2004

Water proofing for Old and New Roof Slab Providing and laying water proofing treatment on roof slab by applying two Component, factory, designed ready to use, acrylic modified flexible material applied with brush roller or spray for water proofing coating as per manufacturer specifications with following steps: (a)surface preparation Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint/ coating, and cement laitance by cleaning with compressed air & water jet Including all materials, labour, tools complete Ponding test to be done after plugging all outlets and la be checked from soft to identify seepage, leakage. On identification of seenage, cement grouting to be done with non shrink expanding admixture of Sika india Pvt.Ltd/MYK Schomberg Dr Fixit Fosroc on equivalient Providing and repating of all corners arid joints such as those between the parapet wall and the roof slab gic shall be chamlered with 150mm X 150 mm fillet of mortar (Cement: sand 1:4) admixed with acrylic polymer of Sika/Fosroc/MYK Schomberg-Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer. Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement Jurry Including all material, labour, tools complete (b)1st Coat -Apply 1st coat of two component acrylic modified, ready to ARKH use, flexible cementitious material on surface saturated dry roof and Inside wall of Parapet wall upto 600 mm by brush or roller After 1st coat of application, 45 gsm of Fibre glass cloth to lay when the first layers still green 1st coat should be applied @1.50 kg/Sqmt/coat. For the purpose of measurement the entire treated surface will be measured (c) 2nd Coat To apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle, to the 1st ogat over the glass fibre laid surface, 2nd coat should be applied 0.7 kg/ Sqml/coat, For the purpose of measurement the entire treated surface will be measured. After three days of drying the 2nd coat, the rain water outlets to be plugged and ponding test to be done for 48 hours to Identify, seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of EIC The waterproof coating to be protected from damage before screed over it Water proofing Brand- Sika Topseal 109hi/Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2K/MYK Aquafin TG Product Performance Chemical Base Part A: Acrylic copolymer, Part B: Specially graded cementitious powder- density 1.6kg/l (mixed density) at+27°c Tensile Strength-2 N/mm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Strength-2 N/mm2 (concrete failure) (According to ISO 4624) Slant-Shear Bond Strength-4 N/mm2 (According to FIP 5.15) Elongation at Break -35% without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) Protection of treated surface with PCC: The treated surface should be covered with 25mm/50mm PCC of M-20 grade (1:1,5:3) with proper slope (1:120) towards the rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 of 100 ml per bag of of cement to be added in the screed concrete (pald separately for this items). All comers shall be chamfered with 150mm X 150 mm fillet. The ratowater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water the peripheral gaps between pvc pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika India Pvt.Ltd./MYK Schomberg/Dr Fixit/Fosroc For the purpose of measurement the entire treated surface will be measured." (e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately). Brand - Sika India Pvt. Ltd./MYK Schomberg/Dr Fixit/Fosroc Warranty for five years.

Covering of treated surface with PCC :- Providing 25 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F.M 2.5 to 3 including screening, shuttering, and mixing cement concrete in mixer with admixture of integral water proofing and placing in position, striking curing, taxes and royality all complete as per building specifiction and direction of E/I. Panels that has been left should be casted next day. There should be 6 mm gap between Panels Brand- Sika_Plastocrate plus, MYK proof WP10, Fosroc-Conplast X421 ic Dr Fixit Pidiproof LW+

GST @ 18%

L.Cess @ 1%