National Rural Employment Programme Tender

Supplying all materials, labour, tools & equipments for fitting & fixing 200mm dia MS cap over casing pipe complete job. (DWSD Item 120 B)

Designing, Supplying, Installation, Testing & Commissioning with all tools & As Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water per Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Quota Guideline with following specifications & accessories, tionA SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PV modules should be minimum 200 watt peak The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required.iii) The PV modules should be mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200km/h. iv) The module mounting structure should be hot dip galvanized according to IS 4759 v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification) vii) Necessary protection such as lightening arrestor etc. should be provided. to protect the controller & SPV viii) The suction/delivery pipe shall be UPVC/H.D.P.E. pipes of appropriate size 60m or more as required minimum pressure rating of 8kg/Sq em- PE 100 grade for pump up to 3HP & 10 Kg/Sq cm-PE 100 grade for 5 HP. ix) All cable used shall be as per 15 694. Suitable size of cable shall be used in sufficient length for inter connection between the SPV array to SPV controller and SPV controller to solar power pump. Provision of cable shall be as per IS 14536. x) The motor pump set should have a 5 years warranty xi) Control panel suitable for motor pump with arrangement of dry run & over flow protection sensor, float switch & rain prevention box. (As per MNRE Specification) xii) The SPV controller must have IP-65 protection or must be housed in cabinet having at least IP-65 protection.xiii) The system should be as per MNRE guide line & Ecofriendly with suitable arrangement to operate new pump manually xiv) With third party inspection before dispatch. xv) Provision for web based remote monitoring of the pumps to be installed must be made through the inbuilt controllers. It should be possible to ascertain the daily water output, the power generated by PV Array the Up and down time of the pump during the year, number of days the pump was unused or under breakdown repairs. The following details should be marked indelibly on the motor pump set a) Name of the Manufacturer or Distinctive Logo.

Providing of solor night lamp

Cost of drilling 200mmX165mmX200 Mtr deep bore well in all kinds of soil and rock in rural area for installation of pump bore set with Hydraulic DTH Rig machine, all complete including supplying all materials, tools, drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicles up to the site. (a) 0.00m Up to 50.00m depth below G.L. In Rural Areas (DWSD 119)

(b) Above 50.00 m depth. In Rural Areas

Supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe etc all complete job. (DWSD Item 120)

Supplying all materials, labour, tools & equipments for fitting & fixing 200mm dia MS cap over casing pipe complete job. (DWSD Item 120 B)

Designing, Supplying, Installation, Testing & Commissioning with all tools & As Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water per Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Quota Guideline with following specifications & accessories, tionA SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PV modules should be minimum 200 watt peak The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required.iii) The PV modules should be mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200km/h. iv) The module mounting structure should be hot dip galvanized according to IS 4759 v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification) vii) Necessary protection such as lightening arrestor etc. should be provided. to protect the controller & SPV viii) The suction/delivery pipe shall be UPVC/H.D.P.E. pipes of appropriate size 60m or more as required minimum pressure rating of 8kg/Sq em- PE 100 grade for pump up to 3HP & 10 Kg/Sq cm-PE 100 grade for 5 HP. ix) All cable used shall be as per 15 694. Suitable size of cable shall be used in sufficient length for inter connection between the SPV array to SPV controller and SPV controller to solar power pump. Provision of cable shall be as per IS 14536. x) The motor pump set should have a 5 years warranty xi) Control panel suitable for motor pump with arrangement of dry run & over flow protection sensor, float switch & rain prevention box. (As per MNRE Specification) xii) The SPV controller must have IP-65 protection or must be housed in cabinet having at least IP-65 protection.xiii) The system should be as per MNRE guide line & Ecofriendly with suitable arrangement to operate new pump manually xiv) With third party inspection before dispatch. xv) Provision for web based remote monitoring of the pumps to be installed must be made through the inbuilt controllers. It should be possible to ascertain the daily water output, the power generated by PV Array the Up and down time of the pump during the year, number of days the pump was unused or under breakdown repairs. The following details should be marked indelibly on the motor pump set a) Name of the Manufacturer or Distinctive Logo.

Providing of solor night lamp

Cost of drilling 200mmX165mmX200 Mtr deep bore well in all kinds of soil and rock in rural area for installation of pump bore set with Hydraulic DTH Rig machine, all complete including supplying all materials, tools, drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicles up to the site. (a) 0.00m Up to 50.00m depth below G.L. In Rural Areas (DWSD 119)

(b) Above 50.00 m depth. In Rural Areas

Supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe etc all complete job. (DWSD Item 120)

Supplying all materials, labour, tools & equipments for fitting & fixing 200mm dia MS cap over casing pipe complete job. (DWSD Item 120 B)

Designing, Supplying, Installation, Testing & Commissioning with all tools & As Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water per Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Quota Guideline with following specifications & accessories, tionA SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PV modules should be minimum 200 watt peak The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required.iii) The PV modules should be mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200km/h. iv) The module mounting structure should be hot dip galvanized according to IS 4759 v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification) vii) Necessary protection such as lightening arrestor etc. should be provided. to protect the controller & SPV viii) The suction/delivery pipe shall be UPVC/H.D.P.E. pipes of appropriate size 60m or more as required minimum pressure rating of 8kg/Sq em- PE 100 grade for pump up to 3HP & 10 Kg/Sq cm-PE 100 grade for 5 HP. ix) All cable used shall be as per 15 694. Suitable size of cable shall be used in sufficient length for inter connection between the SPV array to SPV controller and SPV controller to solar power pump. Provision of cable shall be as per IS 14536. x) The motor pump set should have a 5 years warranty xi) Control panel suitable for motor pump with arrangement of dry run & over flow protection sensor, float switch & rain prevention box. (As per MNRE Specification) xii) The SPV controller must have IP-65 protection or must be housed in cabinet having at least IP-65 protection.xiii) The system should be as per MNRE guide line & Ecofriendly with suitable arrangement to operate new pump manually xiv) With third party inspection before dispatch. xv) Provision for web based remote monitoring of the pumps to be installed must be made through the inbuilt controllers. It should be possible to ascertain the daily water output, the power generated by PV Array the Up and down time of the pump during the year, number of days the pump was unused or under breakdown repairs. The following details should be marked indelibly on the motor pump set a) Name of the Manufacturer or Distinctive Logo.

Providing of solor night lamp

Cost of drilling 200mmX165mmX200 Mtr deep bore well in all kinds of soil and rock in rural area for installation of pump bore set with Hydraulic DTH Rig machine, all complete including supplying all materials, tools, drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicles up to the site. (a) 0.00m Up to 50.00m depth below G.L. In Rural Areas (DWSD 119)

(b) Above 50.00 m depth. In Rural Areas

Supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe etc all complete job. (DWSD Item 120)

Supplying all materials, labour, tools & equipments for fitting & fixing 200mm dia MS cap over casing pipe complete job. (DWSD Item 120 B)

Designing, Supplying, Installation, Testing & Commissioning with all tools & As Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water per Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Quota Guideline with following specifications & accessories, tionA SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PV modules should be minimum 200 watt peak The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required.iii) The PV modules should be mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200km/h. iv) The module mounting structure should be hot dip galvanized according to IS 4759 v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification) vii) Necessary protection such as lightening arrestor etc. should be provided. to protect the controller & SPV viii) The suction/delivery pipe shall be UPVC/H.D.P.E. pipes of appropriate size 60m or more as required minimum pressure rating of 8kg/Sq em- PE 100 grade for pump up to 3HP & 10 Kg/Sq cm-PE 100 grade for 5 HP. ix) All cable used shall be as per 15 694. Suitable size of cable shall be used in sufficient length for inter connection between the SPV array to SPV controller and SPV controller to solar power pump. Provision of cable shall be as per IS 14536. x) The motor pump set should have a 5 years warranty xi) Control panel suitable for motor pump with arrangement of dry run & over flow protection sensor, float switch & rain prevention box. (As per MNRE Specification) xii) The SPV controller must have IP-65 protection or must be housed in cabinet having at least IP-65 protection.xiii) The system should be as per MNRE guide line & Ecofriendly with suitable arrangement to operate new pump manually xiv) With third party inspection before dispatch. xv) Provision for web based remote monitoring of the pumps to be installed must be made through the inbuilt controllers. It should be possible to ascertain the daily water output, the power generated by PV Array the Up and down time of the pump during the year, number of days the pump was unused or under breakdown repairs. The following details should be marked indelibly on the motor pump set a) Name of the Manufacturer or Distinctive Logo.

Providing of solor night lamp

Cost of drilling 200mmX165mmX200 Mtr deep bore well in all kinds of soil and rock in rural area for installation of pump bore set with Hydraulic DTH Rig machine, all complete including supplying all materials, tools, drilling rig, Air Compressor and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicles up to the site. (a) 0.00m Up to 50.00m depth below G.L. In Rural Areas (DWSD 119)

(b) Above 50.00 m depth. In Rural Areas

Supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe etc all complete job. (DWSD Item 120)

Supplying all materials, labour, tools & equipments for fitting & fixing 200mm dia MS cap over casing pipe complete job. (DWSD Item 120 B)

Designing, Supplying, Installation, Testing & Commissioning with all tools & As Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water per Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Quota Guideline with following specifications & accessories, tionA SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PV modules should be minimum 200 watt peak The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required.iii) The PV modules should be mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200km/h. iv) The module mounting structure should be hot dip galvanized according to IS 4759 v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification) vii) Necessary protection such as lightening arrestor etc. should be provided. to protect the controller & SPV viii) The suction/delivery pipe shall be UPVC/H.D.P.E. pipes of appropriate size 60m or more as required minimum pressure rating of 8kg/Sq em- PE 100 grade for pump up to 3HP & 10 Kg/Sq cm-PE 100 grade for 5 HP. ix) All cable used shall be as per 15 694. Suitable size of cable shall be used in sufficient length for inter connection between the SPV array to SPV controller and SPV controller to solar power pump. Provision of cable shall be as per IS 14536. x) The motor pump set should have a 5 years warranty xi) Control panel suitable for motor pump with arrangement of dry run & over flow protection sensor, float switch & rain prevention box. (As per MNRE Specification) xii) The SPV controller must have IP-65 protection or must be housed in cabinet having at least IP-65 protection.xiii) The system should be as per MNRE guide line & Ecofriendly with suitable arrangement to operate new pump manually xiv) With third party inspection before dispatch. xv) Provision for web based remote monitoring of the pumps to be installed must be made through the inbuilt controllers. It should be possible to ascertain the daily water output, the power generated by PV Array the Up and down time of the pump during the year, number of days the pump was unused or under breakdown repairs. The following details should be marked indelibly on the motor pump set a) Name of the Manufacturer or Distinctive Logo.

Providing of solor night lamp

ADD PHOTO GRAPHY

Add cost of 18 % GST

add 1 % labour cess