National Rural Employment Programme Tender

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 S.O.R. Item No. 6.4

Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc. Ordinary Km post S.O.R. Item No. 8.14 (ii)

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing 801. 80 mm x 60 mm rectangular S.O.R. Item No. 8.04 A (X)

Providing and erecting direction and place identifications of semi reflective sign boards as per IRC:67 made of 2 mm thick M.S. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour. Supported and welded on 47 mm x 47mm of 12 SWG Square tube of 3050 mm height duly strengthened by 25 mm x 5 mm M/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701 S.O.R. Item No. 8.05

E/W in excavation for structure as per drawing and technical specification clause 305.1 including setting out, construction of shoring and brading, removal of stumps and other deleterious material and disposal utp a lead of 50m, dressing of sides and bottom backfilling in trenches with excavated suitable material. RCD S.O.R. Item No. 12.1 (I) A (i)

Plain/Reinforced cement concrete in open foundation complete as per drawing and Technical Specifications (P.C.C. Grade M-15) S.O.R. Item No. 11.4 (II) (i)

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. Random Rubble Masonary in C.M. (1:3) in foundation S.O.R. Item No. 11.6 (III) (ii)

Stone masonry work in cement mortar in sub-structure complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. Random Rubble Masonry Work in Cement Mortar 1:3 in S/S S.O.R. Item No. 12.4 (III) (ii)

Plain/Reinforced Cement Concrete on Top of Wall complete as per Drawing and Technical Specifications. (P.C.C. Grade M-15) S.O.R. Item No. 12.5 (I) (i)

Providing weep holes with day grades stone filter of 53 mm to 22.4 mm size in abutment and wing wall all complete job as per specification and direction of E/I. S.O.R. Item No. 13.1 (II)

Pointing with cement mortar (1:3) on brick or stone masonary work as per drawing and technical specification Clauses 613.3 and 1204 S.O.R. Item No. 12.2

Providing and laying boulders pitching for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification. S.O.R. Item No. 16.09

Plain/Reinforced cement concrete in open foundation complete as per drawing and Technical Specifications (P.C.C. Grade M-15) S.O.R. Item No. 12.08 A Case ll

Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications (P.C.C. Grade M-15) S.O.R. Item No. 13.05 A (p)

Stone masonry work in cement mortar 1:3 for substructure complete as per drawing and Technical Specifications Squre Rubble Coarse Rubble Masonry (First Sort) Work in CM 1:3 in foundation S.O.R. Item No. 12.07 A

Stone masonry work in cement mortar 1:3 for substructure complete as per drawing and Technical Specifications Coursed Rubble Masonary in C.M. (1:3) in (First sort) sub-structure S.O.R. Item No. 13.04 B

Stone masonry work in cement mortar in sub-structure complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. Coarse Rubble Masonry Work in Cement Mortar 1:5 in sub-structure S.O.R. Item No. 12.4 (II) (iii)

Stone masonry work in cement mortar in sub-structure complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. Random Rubble Masonary in C.M. (1:4) in sub-structure S.O.R. Item No. 12.4 (III) (ii)

Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications (P.C.C. Grade M-20) S.O.R. Item No. 13.05 B (p)

Furnishing and Placing Reinforced/ Prestressed cement concrete in super-structure as per drawing and Technical Specification (P.C.C. Grade M-25 in Deck Slab) S.O.R. Item No. 13.5 F (p)

Providing and laying Cement Concrete Wearing Coat M-30 grade including reinforcement complete as per drawing and Technical Specifications S.O.R. Item No. 14.04

Supplying, fitting and placing HYSD bar reinforcement in super-structure complete as per drawing and technical specifications S.O.R. Item No. 13.06

Plastering with cement mortar (1:3) on brick or stone masonary work as per drawing and technical specification Clauses 613.3 and 1204 S.O.R. Item No. 13.03

Providing weep holes with day grades stone filter of 53 mm to 22.4 mm size in abutment and wing wall all complete job as per specification and direction of E/I. S.O.R. Item No. 13.08

Backfilling behind abutment,wing wall and return wall with sandy material complete as per drawing and technical specification Clouse 710.1.4 of IRC 78 and 2200 SOR Item no.13.09 B

ADD 18% GST

ADD 1% LABOUR CESS