Indo Tibetan Border Police Tender

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.:Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for : Shelves (Cast in situ)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gm/ltr. of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50gm/ltr.

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes,shelves, racks, almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete. :- Kiln seasoned and chemically treated hollock wood

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Providing and fixing 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge.

Providing and fixing expansion hold fasteners on C.C./R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing magnetic catcher of approved quality in cupboard /ward robe shutters, including fixing with necessary screws etc. complete.

Providing and fixing wall mounted / ceiling mounted industrial Chimney having following specification including testing commssioning and testing charges at site as per direction of engineer in charge. 1.Providing ducting for Hot Air, made of GI sheet 0.50mm = 156.00 Sq ft, Ducting Length 18 feet and ducting area 18' x (18"x4) = 108.00 sqft , Add for Fan Box 48 sqft Total 156.00 Sqft , 2. Providing ducting for Hot Air, made of GI sheet 0.50mm = 156.00 Sq ft, Ducting Length 18 feet and ducting area 18' x (18"x4) = 108.00 sqft , Add for Fan Box 48 sqft Total 156.00 Sqft ,3.Providing Fresh air Ducting, made of GI sheet 0.50mm 1 x 12 x 4 = 48 Ducting Length 18 feet and ducting area 18' x (12"x4) = 72.00 sqft , Add for Fan Box 48 sqft Total 120.00 Sqft , 4.Exhaust Fan For hot air , Size 600 mm , 1 Phase, 1500 RPM, 850 watt , 2.65 Amp, Air Flow -10,520 m3/h , Noise -70 dB-75dB, 5.Exhaust Fan for Fresh Air 380 mm , single Phase 1400 RPM, 166 Watt, 0.70 Amp Air Flow – 3700 m3/h, Noise - 65dB-70dB 01 Nos , 6.Providing Fresher Grill. Size 72"x 8" = 01 Nos, 7.Providing Hot Air Waffle Filter Size -20" x24" = 04 nos, 8.Providing Aluminum Grid Fan Hot & Cold Air Ducting and Fresh air following size. (i) 24"x24"=01 No (ii) 15"x15" = 01 No

Providing and fixing wall mounted / ceiling mounted industrial Chimney having following specification including testing commssioning and testing charges at site as per direction of engineer in charge. 1.S.S Center hood / Chimney 84’’x48’’x20’’ Both Side Fresher and oil Collector Box Double Side (Material of Chimney Stainless Steel 202 & 0.80 mm thick ) 2.Providing Ducting for Hot Air, made of GI sheet 0.50mm = 156.00 Sq ft, Ducting Length 18 feet and ducting area 18' x (18"x4) = 108.00 sqft , Add for Fan Box 48 sqft Total 156.00 Sqft , 3.Providing Fresh air Ducting, made of GI sheet 0.50mm 1 x 12 x 4 = 48 Ducting Length 12 feet and ducting area 12' x (12"x4") = 48.00 sqft , Add for Fan Box 48 sqft Total 96.00 Sqft. For both side of chimney 96.00+96.00 = 192.00 sqft 4.Exhaust Fan For hot air , Size 600 mm , 1 Phase, 1500 RPM, 850 watt , 2.65 Amp, Air Flow -10,520 m3/h , Noise -70 dB-75dB =01Nos,5.Fan for Fresh Air 380 mm , single Phase 900 RPM, 100 Watt, 0.48 Amp Air Flow – 2250 m3/h, Noise - 55dB-60 dB = 02 Nos, 6.Providing Fresher Grill. Size 72"x 8" = 02 Nos,7.Providing Hot Air Waffle Filter Size -20" x24" = 03 nos, 8.Providing Aluminum Grid Fan Hot & Cold Air Ducting and Fresh air following size. (i) 24"x24" = 01 No (ii) 15"x15" = 01 No