Drinking Water And Sanitation Department Tender

Cost for adjusting suction pipe line as required with supplying of 5" dia pipe or suitable dia-2m,flange-2Nos., nut, bolt, washer-5 Kg, rubber insertion-5Kg etc, cutting of pipe in required size and doing complete welding work including all labour, tools, tackle and technician charges.with CP & OHC. (Rate after deducting the scrap materials.)

Cost for adjusting delivery pipe line as required with supplying of 4" dia pipe or suitable dia-5m, bend-2nos., flange-8Nos., nut, bolt, washer-8 Kg, rubber insertion-10Kg etc, cutting of pipe in required size and doing complete welding work including all labour, tools, tackle and technician charges.with CP & OHC. (Rate after deducting the scrap materials.)

Cost for 10 sq. mm x 3 core PVC sheathed & PVC insulated, 1.1 KV grade copper unarmored cable. Make – Havells/Any ISI marked reputed make.

Cost towards making cable mouth for above 3 core x 10 mm2 copper uarmored cable with lugs and jointinting materials etc all complete.

Cost for 16 sq. mm x 3.5 core PVC sheathed & PVC insulated, 1.1 KV grade copper unarmored cable. Make – Any ISI marked reputed make.

Cost towards laying of above cable from Motor Control Panel to motor with saddle work including all labour tools,tackles and technician charges.

Cost towards making cable mouth for above 3.5 core x 16 mm2 copper unarmored cable with lugs and jointinting materials etc all complete.

Cost towards Supplying, Installation, Testing and Commissioning of floor/wall mounted cubical L.T Motor Control Panel fabricated with MS sheet and painted, dust and vermin proof, proper ventilated, consisting of – (a). Copper distribution 100 amp copper bus bar 4 Pole-1 set (b). Micro processor base TPN MCCB 100 Amp L&T/ Siemens /Schneider make with earth fault relay for incoming feeder – 1No., Voltmeter-1No., Ampere meter-1No. & selector switch-2 Nos. (c). MCCB 63Amp. 3ph, L&T/ Siemens /Schneider make for outgoing feeder-2 Nos.(1No for each backwash p/ set) (d) MCB 16Amp. Single phase, for outgoing feeder-2 Nos.(1No for each dewatering p/ set) & 16Amp MCB feeder for lighting and utility-1No. (e). Suitable size of fully automatic star delta starter L&T/ Siemens /Schneider make -2 Nos. (for backwash p/set) (f). Suitable Single phase DOL starter -2 Nos. (for dewatering p/set) (e). Voltmeter-2Nos., Ampere meter-2Nos., Selector switch-4 Nos., Phase indicating lamp-6 Nos., and Single Phase Preventer-2Nos., proper inside wiring with suitable size of copper wire etc all complete & testing on load.

For Dewatering:- Cost towards supplying, installation ,testing & commissioning of monoblock type centrifugal pump of capable to discharge range 21000LPH-4200LPH against head range- 6m-14m, [Make-Crompton Greaves/KSB/Any reputed ISI Marked] with Squirrel cage, induction motor operatig on 220V±10%, 50c/s A.C. Supply having suitable speed for dewatering purpose in pump house, including all labour tools, tackles,technician,with s/f of suitable Sluice valve, foot valve, sutable cable,with suitable size of suction and delivery PVC Pipe-10m, testing of pumpset on full load at site etc all complete.

S.I.T.C. of D.C. Battery Charger:- Cost towards Supply, Installation, Testing and Commissioning of Automatic 110 V Float & Boost Battery Charger for Battery Bank etc all complete , testing on full load at site including all labour tools, tackles and electrician cost all complete. Liveline/Any reputed make. (Rate after deduction of the scrap materials.)

Cost towards supply, delivery and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 300 sq. mm, 3core XLPE insulated armoured aluminium conductor cable of 11KV grade including all labour,tools,tackles and technician. (Rate after deducting the scrap materials.)

Supplying, Fitting, Installation, erecting and Commissionning of approved make H.T. outdoor type gang operated air break triple pole switch, Suitable for 11KV line, Rotating type,with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of G.I. pipe for operating handle erected on extended square shaft. The operating handle provided with lock and key at suitable height from ground with necessary clamps including CP, OHC,transportation,labour charges etc. (Rate after deducting the scrap materials.)