Drinking Water And Sanitation Department Tender

Cost for fitting of sluice valve, NR valve with supply fitting of rubber insertion- 03 Kg nut bolt & washer ¾’ dia x 4’ long – 16 nos., 4” dia m/s pipe, 5’ long – 01 no., cutting and welding of pipe to common header with gas cutter & welding set and making leak proof joint testing on load including all labour tools and tackles.

Renovation of existing electrical panel suitable for 40HP VT pump setsb including supplying and fitting following:- (A) Incoming feeder - (i) 100 amp MCCB – 01 no. (ii) 200 amp copper bus bar arrangement (4 pole). (iii) Phase indicating lamp-02 nos. (B) Out going feeder (i) 63 amp MCCB – 2 Nos. (ii) Volt meter – 1 no. (iii) Amp meter – 2 nos. (iv) Pilot lamp – 4 nos. (v) Selector switch – 2 nos. (vi) FASD (ml-04) starter – 1 no. (vii) Single phase preventor – 2 nos. Complete internal wiring with suitable size of copper wire and testing on load.

Cost for supplying and laying of 35 mm2x 3 core PVC insulated and PVC sheathed copper conductor for power wiring from panel to motor for -02 sets.

Cost for supplying and erecting of earthing station as per IE rule including the cost of earth pit, 8 SWG copper wire, G.I. pipe all complete with sand, charcoal and salt etc to all electrical equipment in double way wire connection.

Repairing of 100 kva powerline servo controlled voltage stabilizer with disconnecting all electric lines and joints and dismantle the 100 KVA stabilizer for checking defects and removing them with all labour tools and tackles etc. at site.

(i)Supplying and fitting 10 kg operating motor.

(ii) Supplying and fitting Voltmeter.

(iii) Supplying and fitting Ammeter.

(iv) Supplying and fitting Big neon light.

(v) Supplying and fitting control card.

(vi) Supplying and fitting variac autotransformer 100 amp.

(vii) Supplying and fitting control transformer.

(viii)heating and filteration of 100 KVA Stablizer colling oil at site

supplying, installation and commissioning of efficient motor pump sets, stabilizer, capacitor bank with all accessories and all allied works so as to save energy consumption for the rural water supply pumping plant Lachragarh

Cost for supplying, installation and commissioning of vertical turbine water lubricated single or multi stage pump set of Kirloskar/Jyoti/ M&P/WPIL make capable for discharge 41.5 m3/hr against a total head of 60 mtr with suitable size of coloum assembly (MS), flange type 10’ long each heavy duty with line shafts, 60’(feet) spider bearings, cuttless rubber bushes, sleeves and discharge head etc as required coupled with suitable size of hollow/solid shaft, squirrel cage energy efficient IE3 induction motor as per IS 12615 : 2011 with latest Amendments operated on 415 volt 3 phase, 50 c/s, 1400-1500 rpm with non reversible rather coupling (make Kirlosker/Jyoti/CGL/ABB or reputed) with suitable size of ISI marked heavy duty CIDF sluice valve, CIDF NR valve, pump strainer M/S clamp- 02 pair etc all complete and testing on load.

Supply and fitting common header 4’’ GI Pipe with welding and jointing with bent as required at site.

Cost for fitting of sluice valve, NR valve with supply fitting of rubber insertion- 03 Kg nut bolt & washer ¾’ dia x 4’ long – 16 nos., 4” dia m/s pipe, 5’ long – 01 no., cutting and welding of pipe to common header with gas cutter & welding set and making leak proof joint testing on load including all labour tools and tackles.

Cost for supplying, installation and commissioning of motor control panel made of 2 mm thick cubical panel board heat and vermine proof, proper ventilated two coats of appox painted comprising of (A) Incoming feeder - (i) 100 amp MCCB – 01 no. (ii) 200 amp copper bus bar arrangement (4 pole). (iii) Phase indicating lamp-03 nos. (B) Out going feeder (i) 63 amp MCCB – 2 Nos. (ii) Volt meter – 2 nos. (iii) Amp meter – 2 nos. (iv) Pilot lamp – 6 nos. (v) Selector switch – 4 nos. (vi) FASD (ml-04) starter – 2 nos. (vii) Single phase preventor – 2 nos. Complete internal wiring with suitable size of copper wire and testing on load.

Cost for supplying and laying of 10 mm2x 3 core PVC insulated and PVC sheathed copper conductor for power wiring from panel to motor for -02 sets.

Cost for making arrangement for socketing of wire with thumble and making all line connection (A) 90 mm2 alluminium thumble – 04 nos. -------------

(B) 25 mm2 copper thumble – 24 nos. -------------------

Cost for supplying and erecting of earthing station as per IE rule including the cost of earth pit, 8 SWG copper wire, G.I. pipe all complete with sand, charcoal and salt etc to all electrical equipment in double way wire connection.

Supplying installation testing and commissioning of 90 watt LED (make Havell’s, Bajaj, reputed) at existing pole and building along with suitable arm/bracket wire 1.5 mm2, switch etc all complete.

Supplying, installation & commissioning 50 KVA roller type Servo stabilizer switch for input voltage 280 to 460 volts output voltage of 415 volt ±1%, 3 phase 50 Hz with copper wound transformer (oil cooed) as mentioned below. The stabilizer shall function satisfactorily even if incoming supply is unbalanced between phase within range of 10%. The stabilizer should be constructed in cubical box, with bidirectional wheels for easy hanlding, necessary monitors and users controls on front panel such as indication, alarm, volt meter and selector switch for measuring input and output voltage, auto/manual selector switch, raise/low push button etc. suitable capacity termination strips and bus bar for incoming and out going cable should be provided. All three phases shall be independently monitored and connected following protections and indication shall be incorporated (i) Over voltage/under voltage (ii) Single phasing (iii) Cut off contactor with electronic output sensing unit make servokon/powerline/ISI marked reputed make.

Supplying and fitting 200 A change over switch, L&T/Havell’s make/C&S make or ISI reputed make.

Supplying and filling transformer oil including filtration, universal/vedol/ cultax.

Supplying, laying and fitting 95 mm2 x 3.5 core Alluminium armoured cable Universal/Polycabe make.

Transportation and installation charges with all tools, tackles and labour including loading and unloading charges.

Supply installation and commissioning of APFC panel with MCB consisting of followings: (i) 10 KVAR in required steps. (ii) TPN MCCB 32 amp. (iii) APFC relay. (iv) Contactor MOC 5 Nos, (v) Phase indication & On, Off Trip indicator. (vi) LED type/22.5 dia. (vii) 2 way switch (viii) 3 way switch (ix) HRC fuse for APFC relay. (x) CT coil. With suitable copper bus bar in 16 SWG steel fabricated cubical type wall mounted panel board including loading unloading and transportation cost etc all complete. Testing on full load at site.

supplying installation & commissioning of two motor suitable for HSC C/F pump having discharge 29.58 m3/h and Head 68 Mtr and two motor suitable for HSC C/F pump having discharge 25.50 m3/h and Head 32 Mtr For Agharma Rural water supply scheme Simdega

Clear water pumping Plant

Supply, Installation and commissioning of hollow shaft motor of Jyoti/ Kirloskar/ Crompton make suitable for pump capable of discharge 29.58 m3/h against total head of 68 meter, including cost of supplying, fitting & fixing of all required coupling. including Transportation, Loading & unloading charges All complete.

Supply, Installation and commissioning of hollow shaft motor of Jyoti/ Kirloskar/ Crompton make suitable for pump capable of discharge 25.50 m3/h against total head of 32 meter, including cost of supplying, fitting & fixing of all required coupling. including Transportation, Loading & unloading charges All complete.

Repairing of starter suitable for above motor.

Raw water pumping Plant

Cost of dismantling the motor and taking out bowl assembly and Re-Assemble Motor and bowl assembly from the intake well by supplying all labour, tools and tackles etc at site.

Supplying all labour tools and tackles for complete dismantling and opening of 30 HP, 3 phase induction motor, cutting burnt wire and rewinding super enameled copper wire , insulating paper, tape bamboo stick etc. Heating Varnishing and testing on full load at site including transportation charge after deducting the cost of scrap materials (burnt wire wt. 15 Kg approx) for set No-1

Cost for supplying and laying of 50 mm² x 3.5 core XLPE armoured Aluminium cable PVC insulated and sheathed from starter to motor.