Drinking Water And Sanitation Department Tender

Making of New PCC foundation size 3’ x 2’ x1’ with all labour tools & materials such as cement, sand, stone, chips, ¾” dia x 1” long, foundation bolt with nut and washer etc all complete.

Fitting of sluice valve, NR valve with supply fitting of rubber insertion- 03 Kg nut bolt & washer ¾’ dia x 4’ long – 16 nos., 4” dia m/s pipe, 5’ long – 01 no., cutting and welding of pipe to common header with gas cutter & welding set and making leak proof joint testing on load including all labour tools and tackles.

Supplying, installation and commissioning of motor control panel made of 2 mm thick cubical panel board heat and vermine proof, proper ventilated two coats of appoxy painted comprising of (A) Incoming feeder - (i) 160 amp MCCB – 01 no. (ii) 160 amp copper bus bar arrangement (4 pole). (iii) Phase indicating lamp-03 nos. (B) Out going feeder (i) 100 amp MCCB – 2 Nos. (ii) Volt meter – 2 nos. (iii) Amp meter – 2 nos. (iv) Pilot lamp – 6 nos. (v) Selector switch – 4 nos. (vi) FASD starter – 2 nos. (vii) Single phase preventor – 2 nos. Complete internal wiring with suitable size of copper wire and testing on load.

Supplying and laying of 25 mm2x 3 core PVC insulated and PVC sheathed unarmoured copper conductor for power wiring from panel to motor for -02 sets.

Making arrangement for socketing of wire with thumble and making all line connection (A) 95 mm2 aluminum thumble – 04 nos.

(B) 25 mm2 copper thumble – 24 nos.

Supplying and erecting of earthing station as per IE rule including the cost of earth pit, 8 SWG copper wire, G.I. pipe all complete with sand, charcoal and salt etc to all electrical equipment in double way wire connection.

Supplying installation testing and commissioning of 90 watt LED (make Havell’s, Bajaj, reputed) at existing pole and building along with suitable arm/bracket wire 1.5 mm2, switch etc all complete.

Supplying, installation & commissioning 75 KVA roller type Servo stabilizer switch for input voltage 280 to 460 volts output voltage of 415 volt ±1%, 3 phase 50 Hz with copper wound transformer (oil cooed) as mentioned below. The stabilizer shall function satisfactorily even if incoming supply is unbalanced between phase within range of 10%. The stabilizer should be constructed in cubical box, with bidirectional wheels for easy handling, necessary monitors and users controls on front panel such as indication, alarm, volt meter and selector switch for measuring input and output voltage, auto/manual selector switch, raise/low push button etc. suitable capacity termination strips and bus bar for incoming and out going cable should be provided. All three phases shall be independently monitored and connected following protections and indication shall be incorporated (i) Over voltage/under voltage (ii) Single phasing (iii) Cut off contactor with electronic output sensing unit make Servokon/ Powerline/ Powerstar/ ISI marked reputed make.

Supplying and fitting 160 A change over switch, L&T/ Havell’s make/ C&S make or ISI reputed make.

Supplying and filling transformer oil, Universal/ Vedol/ Cultax or reputed ISI.

Supplying, laying and fitting 95 mm2 x 3.5 core Alluminium armoured cable Universal/Polycab/Mescab/ISI reputed make.

Transportation and installation charges with all tools, tackles and labour including loading and unloading charges.

Supply installation and commissioning of APFC panel with MCB consisting of followings: (i) 30 KVAR in required steps. (ii) TPN MCCB 32 amp. (iii) APFC relay. (iv) Contactor MOC 5 Nos, (v) Phase indication & On, Off Trip indicator. (vi) LED type/22.5 dia. (vii) 2 way switch (viii) 3 way switch (ix) HRC fuse for APFC relay. (x) CT coil. With suitable copper bus bar in 16 SWG steel fabricated cubical type wall mounted panel board including loading unloading and transportation cost etc all complete. Testing on full load at site.

II. CLEAR WATER P/PLANT KAPALI Supplying, installation and commissioning of HSC C/F pump single or multi-stage pump set of Kirloskar/Jyoti/M&P/ WPIL make capable for discharging 73 m3/hr against total head of 31 mtr, coupled with suitable size energy efficient induction motor three phase squirrel cage motor operated on 415 volt 3 phase, 50 c/s, 1450 rpm (make as per energy efficient IE3 induction motor as per IS 12615 : 2011 with latest Amendments motor) with suitable size of ISI marked heavy duty CIDF sluice valve, CIDF NR valve(size 100mm) etc all complete and testing on load.

All labour, tools and tackles for breacking of Old PCC foundation size 5’X4’X4’ and removing all garbage from pump house to out side.

Making of new PCC foundation size 5’x4’x4’ with all labour, tools, tackles & technician and materials such as cement, sand, stone, chips, ¾’dia x 3’ long foundation bolt-6 nos. with nut and washer etc all complete.

Fitting of sluice valve, N.R. valve with s/f of rubber insertion.-3 kg, ¾” x 4” long bolt with nut and washer-16 nos. m/s pipe 5’ long-01 No. cutting and welding of pipe to common header with gas cutter and welding set and making leak proof joint including loading, unloading & transportation cost.

Supplying, installation and commissioning of motor control panel made of 2 mm thick cubical panel board heat and verming proof, proper ventilated two coats of appoxy painted comprising of (A) Incoming feeder - (i) 100 amp MCCB – 01 no. (ii) 100 amp copper bus bar arrangement (4 pole). (iii) Phase indicating lamp-3 nos. (B) Out going feeder (i) 63 amp MCCB – 2 Nos. (ii) Volt meter – 2 nos. (iii) Amp meter – 2 nos. (iv) Pilot lamp – 6 nos. (v) Selector switch – 4 nos. (vi) FASD starter – 2 nos. (vii) Single phase preventor – 2 nos. Complete internal wiring with suitable size of copper wire and testing on load.

Supplying and laying of 16 mm2x 3 core PVC insulated and PVC sheathed unarmoured copper conductor for power wiring from panel to motor for -02 sets.

Making arrangement for socketing of wire with thumble and making all line connection (A) 100 mm2 aluminum thumble – 04 nos.

(B) 16 mm2 copper thumble – 24 nos.

Supplying and erecting of earthing station as per IE rule including the cost of earth pit, 8 SWG copper wire, G.I. pipe all complete with sand, charcoal and salt etc to all electrical equipment in double way wire connection.

Supplying installation testing and commissioning of 90 watt LED (make Havell’s, Bajaj, reputed) at existing pole and building along with suitable arm/bracket wire 1.5 mm2, switch etc all complete.

Supplying, installation & commissioning 50 KVA roller type Servo stabilizer switch for input voltage 280 to 460 volts output voltage of 415 volt ±1%, 3 phase 50 Hz with copper wound transformer (oil cooled) as mentioned below. The stabilizer shall function satisfactorily even if incoming supply is unbalanced between phase within range of 10%. The stabilizer should be constructed in cubical box, with bidirectional wheels for easy hanlding, necessary monitors and users controls on front panel such as indication, alarm, volt meter and selector switch for measuring input and output voltage, auto/manual selector switch, raise/low push button etc. suitable capacity termination strips and bus bar for incoming and out going cable should be provided. All three phases shall be independently monitored and connected following protections and indication shall be incorporated (i) Over voltage/under voltage (ii) Single phasing (iii) Cut off contactor with electronic output sensing unit make Servokon/ Powerline/ Powerstar/ ISI marked reputed make.

Supplying and fitting 125 A change over switch, L&T/Havell’s make/C&S make or ISI reputed make.

Supplying and filling transformer oil, Universal/Vedol/ Cultax

Supplying, laying and fitting 70 mm2 x 3.5 core Aluminum armoured cable Universal/Polycab make.

Transportation and installation charges with all tools, tackles and labour including loading and unloading charges.

Supply installation and commissioning of APFC panel with MCB consisting of followings: (i) 20 KVAR in required steps. (ii) TPN MCCB 32 amp. (iii) APFC relay. (iv) Contactor MOC 5 Nos, (v) Phase indication & On, Off Trip indicator. (vi) LED type/22.5 dia. (vii) 2 way switch (viii) 3 way switch (ix) HRC fuse for APFC relay. (x) CT coil. With suitable copper bus bar in 16 SWG steel fabricated cubical type wall mounted panel board including loading unloading and transportation cost etc all complete. Testing on full load at site.

GST 12%

Labour Cess 1%