Building Construction Department Tender

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp proof course 50 mm thick with cement concrete 1:2:4(1cement :2coarse sand(zone-iii):4 graded stone aggregate 20 mm nominal size

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form forWeather shade, Chajjas, corbels etc., including edges

Providing fixing pressed steel door frame conferming to IS:4351 manufactured from commercial mild steel sheet of 1.60mm thickness including hinges,jamb,lock jamb,bead and if required angle threshold of mild steel angle section 50x25mm or base tiles of 1.60 mm pressed mild steel welded or rigidly fixed together by mechanical means including M.S.pressed butt hinges 2.5mm thick with mortar guards,lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as direction of E/I. Profile-C,Fixing with carbon steel galvanised dash fastener of requied dia and size Fixinng wih adjustable lugs with split end tail to each jamb)

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

providing Tor steel reinforcement of 8mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(8mm dia )

(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

(b) 12mm to 20mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

Supplying fitting and fixing M.S.Grill made of 20x6mm M.S.flat squre bar as per approved design and drawing properly fabricated with joints continous fillet welded and finished smooth carriage of grill to work site,hoisting as per building specification and direction of E/I(where materials to not supplied by the deptt)

Supplying, and fixing fan hook of 16mm dia M.S. bar 1 meter long bent to required size and shape , placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where materials is not supplied by the deptt.)

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 20 guage G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

(iv) 600X600 mm size

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;31 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Water proofing for Old and New Roof Slab:- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with. brush, roller or spray for water proofing coating as per manufacturer specifications with following steps: (a) surface preparation:-Providing and cleaning of concrete surface to remove dust, oil, grease Including removal of existing loose paint/ coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to Identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika India Pvt.Ltd. / MYK Schomberg Dr Fixit/Fosroc or equivallent. Providing and reparing of all corners and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150mm X 150 mm fillet of mortar (Cement: sands 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer. Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same withcement slurry including all material, labour, tools complete. (b)1st Coat Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application, 45 gsm of Fibre glass cloth to lay when the first layer is still green 1st coat should be applied @1.50 kg/SqmU/coat. For the AND purpose of measurement the entire treated surface will be measured." (c) 2nd Coat :-To apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the 1st coat over the glass fibre laid surface, 2nd coat should be applied @0,7 kg/ Sqmt/coat. For the purpose of measurement the entire treated surface will be measured." After three days of drying the 2nd coat, the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofing Brand:- Sika Topseal 109hl /Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2K/MYK Aquafin TG Product Performance- Chemical Base Part A: Acrylic copolymer, Part B: Specially graded cementitious powder- Density 1.6 kg/l (mixed density) at +27°C Tensile Strength - 2 N/mm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Strength -2 N/mm2 (concrete failure) (According to ISO 4624) Slant-Shear Bond Strength-4 N/mm2 (According to FIP 5.15) (According to ASTM D 2370) Elongation at Break -35% without Fibre Cloth and 20% with Fibre Cloth (According To ASTM D 2370) (d) Protection of treated surface with PCC The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1,5:3) with proper slope (1:120) towards the rain outlets in alternate panels of 2 mt x 2mt keeping 6 mm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 @ of 100 ml per bag of cement to be added in the screed concrete (paid separately for this items). All comers shall be just leveled with the screed concrete to ensure smooth discharge VERNMES of water-the peripheral gaps between pvc pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture Insensitive epoxy putty of Sika India Pvt.Ltd./MYK Schomberg / Dr Fixit/Fosroc .For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with Polysulphide Sealant. (Paid Separately). Brand- Sika India Pvt.Ltd. /MYK Schomberg/Dr Per M AND Fixit/Fosroc Warranty for five years.

covering of trreated surface with P.C,C .Providng 50mm thick cemet concrete M20(1:1.5:3)maintaing slope in alternate 2mtx2mt panels with approved quality of stone chips of 20mm to 6mm sizie graded and cleaned sand of F.M 2.5 to3 includig screening,shuttering and mixing cement concretein mixer with admixture of integral water proffing and placing in position,skirting curing,taxes and royalty all complete as per buidings specification and direction of e/I.panels that has been left should be casted next day.there should be 6mm gap between panels Brand sika plastocrate plus,MYK proof WP 10,FOSROC CONPLASTX421 ICX dR.fIXIT PIDIPROOF lW+-do-all complete job(old surface)

Providing and filling of 6mm thick Groove beetween 50mm PCC panels with 6mm thick 25mm deep thermocol strip and filling the rest 25mm with polyesulphide sealant (poring Grada) as per drawing and technical specification and direction of E/I with 18% GST) Brand sika polysulphaide foasroo thioles Cood Dr.Fixit pidiseal PS(42P)MYK seal PS or Etrivlent.

Providing and fixing 1 8 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 : 4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18mm thick marble stone counters venities etc.including maching polishing to edge to give hight gloss finish etc complete as per design approved by E/I.Granite work

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1 : 4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion(i)single socketed pipes.

75mm dia

110mm diameter

Providing and fixing on wall face unplasticised PVC moulded fittings, accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring confirming to IS:5382 leaving 10mm gap for thermal expansion.

Couplar 75mm dia

Coupler 110mm dia

Single pushfit coupler 75mm dia

Single pushfit coupler 110mm dia

Single Tee with door

75x75x75mm

110x110x100mm

Single Tee with out door

75x75x75mm

110x110x100mm

Bend 87’5

75mm dia

110mm

shoe(plain)

75mm dia

110mm dia

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50mm hard wood plugs,screwed with M.S screws of required length, including cutting brick work and fixing in cement mortar 1:4(1cement:4 coarse sand) and making good the wall etc.complete.

110mm dia

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. E/I.

Providing and fixing alumiunum work for door ,windows ,ventilators and partitions with extruded built up standard tubular sections, appropriate z sections and other sections of approved make conforming to IS:733 and IS:1285,fixed with dash fasteners of required dia and size including necessary filling up the gaps at junctions,i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight ,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling C.P. brass/stainless steel screws .all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing and paneling to be paid for separately) Anodised aluminium (anodised transparent or dyed to requireid shade according to IS:1868,Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, windows ,ventilator shutters and partitions etc with EPDM rubber/neoprene gasket etc complete as per the architectural drawings and the directions of E/I.(cost of aluminium snap beading shall be paid in basic item) with float glass panes of 4.0mm thickness(weight not less than 10kg/sqm)

Supply of stainless steel wire guage(Grade 304) aperture 1.4 mm and nominal dia of wire 0.50mm including all complete job as per direction of E/I.

Filling the gap in between aluminium frame &adjacentR.C.C/Brick/stone work by providing weataher sillcon sealantover backer rod of approved quality as per architectural drawings and direction of E/I.Upto 5mm depth and 5mm width.

Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade of: New work (two or more coats applied @ 1.43ltr/10sqmm over and including priming coat of exterior primer applied @ 0.90 litre/10sqm

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer,over the plastered wall suface to prrepare the surface even and smooth complete.job as per direction of E/I.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding , curing and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I.

Carriage of materials from nearest approved sources of supply including loading into trucks and unloading from trucks and stacking properly at work site as directed by the E/I.

Brick lead 8K.M(1K+7P)

sand lead 8K.M.

chips lead 22K.M.

Stone Metal 20 km lead

local sand lead 3K.M

S/F/F VIP Bath room fitting including all complete job as per direction of E/I.

pillar cock (Long neck)

Bib cock(ISI)

Central Hole basin mixer(Best quality)

Swan Neck Tap with left hand operating knob(ISI Maraked) including all complete job.

wall mixer with provision for over head shower with elbow coupling and wall flange

Pressure Adjustable shower with revolving joints

Towel Rail 24"

Towel Ring

soap dish

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(a) 25 mm dia wt not less than 500 gms

(a) 32 mm dia wt not less than 700 gms

Cutting chajja or concrete for laying G.I pipe and restoring the same with R.C.C (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/l.

Making holes in walls for laying G.I pipes and restoring the same after pipe laying as per specification and direction of E/l

(b) 250 mm thick wall.

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l. (b) Mirrors of 6mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror

(1)600x450 mm size

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/l.

(a) For classification of soil item- A

Labour for laying, fitting and fixing NP2 R.C.C. spun pipe with collars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak proof including providing sight rails, bonning rod, night guard, red light and barrier etc. all complete as per specification and direction of E/l.

150 mm dia R.C.C. spun pipe Upto 3.0 meter depth of invert below G.L.

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.)along with earth work in excavation and 80mm thick P.C.C(1:3:6) in foundation and refilling all complete as per specification and direction of E/l.

Supply of NP2 R.C.C.Hume pipe with collar as per I.S.s.458-1971 grade including all taxes and duties all complete job.150mm dia

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china pedestal for wash basin completelyrecessed at the back for the reception of pipes and fitting including all complete job as per direction of E/I.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 610x510 mm bowl depth 200 mm

Providing and fixig P.V.C.waste pipe for sing or wash basin including P.V.C.waste fitting Flexibe pipe 40mm dia including all complete job.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous chinaflushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flushbend, overflow arrangement with specials of standard make and mosquitoproof coupling of approved municipal design complete, including paintingof fittings and brackets, cutting and making good the walls and floorswherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and placing on terrace(at all floor levels) polyethylene water storage tank ISI 12701 marketed with cover and suitable locking arrangement and making necessary holes for inlet ,outlet and overflow pipes but without fillings and the base supported for tank.

Providing and fixing Chlorinated polyvinyl chloride (CPVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e. fixing the pipe with clamps at 1.m.spacing.This included jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(Internal work)(Exposed on wall)

25mm nominal outer dia pipes

32mm nominal outer dia pipes

Providing and fixing Chlorinated polyvinyl chloride (CPVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e. fixing the pipe with clamps at 1.m.spacing.This included jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(Internal work)(Concealeld work)

15mm nominal outer dia pipes

20mm dianominal outer dia pipes

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Wiring for light/fan point/exhaust fan point/call bell Point with 1.5 sq.mm FRPVC insulated copper Conductor single core cable in surface/recessed PVC conduct with Modular type switchmodular plate, Suitable size G.I Box etc. as required.

group B

Wiring for light / Power plug with 2×4 sq mm FRPVC in insulated copper conductor single core cable in surface / recessed PVC conduit along with 1 nos 4 sqmm. FR PVC insulated copper conductor single core cable for loop earthing as required .

Wiring for circuit/submain wiring along with each wire with the following sizes FRPVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5sqmm+1x1.5sqmm earth wire

2x2.5sqmm+1x2.5sqmm earth wire

4x6sqmm+2x6.0sqmm earth wire

Supplying anf dixing of following sizie of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20mm

S/F Modular type switch/socket supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connections but excluding modular plaate etc as reqd.

5/6 Amps One way Switch

5/6 amps,3 socket outlet

Telephone socket outlet

T.V antenna socket outlet

S/F Modular type electronic fan regularor_Supplying and fixing stepped type electronic fan regulator on the existing modular plate swith box including connections but excluding modulalr plate etcas required.

S/F light plug point with modular type accessories :- Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch. corutection, painting etc. as required (For light plugs to be used in non residential buildings)

S/F power plug point with modular type accessories :- Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fxing 6 pin 15/16 amps modular socket outlet and l5/16 amps modular switch. connection, painting letc. as required (For light plugs to be used in non residential buildings)

S/F 2 Pin 5 Amp ceiling rose on the existing junction Box wooden block incuidng connection etc as reqd

S/F Brass batton / Angle Holder including connection etc as reqd

Supplying and fixing Electronic musical call bell single phase 230 volt complete as requred

I.T.C.of exhaust Fan up to 450mm sweep in the existing 0pening including making the hole to suit the size of the above fan making good the damage connection testing commissioning etc. as reqd.

Supplying and fixing the following way,horizontal type three pole and netural, sheet steel M.C.B.ditrubutionbaord,415volts, on surface/recess, complete with tinned copper busbar, neutral bus bar, earth bar,din bar, interconnection powder painted including earthing etc as required ( butwithout MCB/RCCB/Insolator)

4way(4+12) Double door,Horizontal type

S/F”B” series SPMCB: supplying and fixing 6 amps to 32amps rating,240 volts ,10KA,"B" curve, ,miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections ,testing and commissioning etc as required.

6/32 amps,single pole."B" series

Supplying and faixing Following rating, four pole 415 Volts isolator in the existing MCD DB complete with connection testing and commissioning etc as reqd

40 amps

I.T.C of floowing rating LED Street lighting luminarie with pressure die cast and toughened glass cover (IP 66 protection) in existing pole/pipe for pply voltage'1.00-270Y AC,50Hz. Luninarie shall be confirm to IS: 10322 partsection- 3 and sha-ll be complete with all neccssary accessories as required

20W LED Street light

Supply Installation,testing and commissioning of follwing size ceiling fan 3 Bleades confirming to IS:374:2019 including wiring the down rods of standard length(upto 30cm) with 1.5 sqmm FR PVC insulated ,copper wire suitable for 230V 50Hz,single phase supply etc.complete as required.

1200mm(48")BI DC 5 star rating 32W ceiling Fan

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230 V 50Hz,single phase supply etc.complete as required.

20/22 W LED Tube light

Supply and fixing 15/16 watt LED Bulb including all complete job as per direction of E/I.

Supply and fixing 9/10 watt LED Bulb including all complete job as per direction of E/I.

Supply of metal Exaust Fan 12"(300mm) including all complete job as per direction of E/I.make Bajaj/crompton/Havells.)

Cost of Drilling200mmx165mmx125mtrdeep bore well in all kind of soil and rock inrural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials,tools drilling rig-air compressure and equipments as well as fule,llubricants and cost of transportation of rig machine and other vehical up to site.

(a)From 0.00M to 50.00M below G.C

(b)From 51.0M to 150.00M

Supplying assembling lowering and fixing in vertical position inbore well,unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS 12818,including required hire and labour charges,fittings & accdssoreis etc.all complete for all depths,as per direction of E/I.

Development of tube well in accordance with IS: 2800(Part-I) and IS:11189,to establish maximum rate of usable water yield without sand content (beyond peermissible limit)with required capacity aircompressor,running the commpressor for required time till well isfully developed,measuring yield of well by "V" notch method or anyother approved method,measuring static level & draw down etc by step draw down method,collecting wataer samples& getting testeding approved laboratory,I/C disinfection of tube well,all complete including hire & labour charges of air compressor,tools & accessones etc ,all as per requiement and direction of E/I.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe,removable as per rrequirement all complete for borewell of 200mm dia

Providing and fixing M.S.clamp of required dia to the top of casing/housing pipe of tubewell as per IS 2800(partI) including necessry bolts& nuts of required size complete.200mm clamp

Supplying 100mm the submersible pump sets confirming to 8034 and motor confirming to IS 9283 pumpshall be suitable for various delivery head and discharge with stainless steel pump shaft and polyprophylne/noryl impelleer,Motor suitable for working on 415+10,3HP,50 Hz,AC supply with cable guarad,thurst carbon/fiber bearig to with stad entire hydraulic thurst,wataer proof winding shall be provided.The pump set shall be suitable or diret coupling pump shall havge suitable outlet as per manufacturers design.Anti thurst stream lined nonreturn valve shall be provided with pump,3 meter submersible copper conductor cable in single/double run shall be provided witheach pump.Submersible pump set 100mm dia(withpolypropylene/Noryl limpeller) upto20 stages. 2 H.P

Supplying fitting and fixing of standered make starter pannel Board with arrangment of all necessury protection including all taxes,royalty etc all complete job as per direction of E/I.Kalinga submersible flat cable 3 core 100mm 10 sqmm D.O.L Stater with S.S. enclosure with 380/415 volt coil 5 to 10 HP

S/F/F 3 crore 4 sqmm flat copper submersible cable FINOLEX/HEVELS make including all taxes,royalty etc all complete job as per direction of E/I/.Kalinga ksubmersible flat cable 3 core 100mm 10 sqmm

supplying fitting and fixing of 50mm dia G.I.pipe including all complete job.

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)