Building Construction Department Tender

Taking down C.A. Of G.C.I. Sheet in roofs with ridges including stacking the serviceable materials within 15M. Lead and disposal of unserviceable materials with all leads as per direction of E/I.

Taking down old door and window shutters including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down chaukhats in doors including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking sown chaukhats in windows including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying polished vitrified floor tiles in different sizes(Thickness to be specified by the manufacture) with water absorption’s less than 0.08% and conforming to IS:15622 of approved make in all colours and shades,laid on20mm thick cement mortar 1:4(1cement:4 coarse sand)@ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel,plier,wedge,clips of required thickness,leveling system and rubber mallet for placing the tiles gently and easily.Glsazed viterified floor tiles including all complete.(size 600x1200mm)

Providing and laying ceramic glazed floor tiles300x300mm (thickness to be specified by the manufacturer) of Ist quality conforming to IS:15622 of approved make in colours such as white,Ivory,Grey,Fume,Red Brown ,laid on 20mm thick bed of cement mortar 1:4(1cement:4 coarse sand) joints with grey c ement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.. complete. job as per direction of E/I

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.

With commercial grade white 15X15cm Tiles.

Providing and fixing factory made door frame (single rebate) made out of solid foam PVC extruded profile of minimum 60 mm width and minimum 30 mm thickness, having homogenous fine cellular structure and integral smooth outer skin. The frame’s vertical and horizontal members to be mitered cut and joined together with PVC solvent adhesive / cement and both corners strengthened with fully threaded steel screws (of required size) fixed diagonally. The door frame is to be fixed to door jambs using 6 Nos. SS 304 grade minimum 8 mm dia CSK Phillips stainless steel self tapping screws/fasteners with PA6 grade polyamide sleeves both of required size, and gap if any between the door frame and the jamb must be filled with clear silicon, complete as per direction of the Engineer-in-Charge

Providing and fixing factory made PVC door shutter made of solid foam PVC profiles of thikness 5 mm and 15 mm at edges integrally extruded for vertical style and horizontal (top/ bottom/ lock) rails of minimum cross section of 70mmx 28mm, of shape and design as per manufacturer’s specifications having homogenous fine cellular structure and smooth integral outer skin, inserted with G.I. ‘C’ section/ rectangular tube profile of minimum 0.30 mm thickness with 120 gsm coating as stiffeners as per manufacturer’s specifications Mitred cut joints for styles and rails provided with telescopic polymeric ‘L’ corners are jointed together using solvent adhesive and strenghtened with fully threaded stainless steel screws (of required size) through reinforced stiffener with paneling of specified solid foam PVC board/ high pressure laminate of required thickness and of approved design and shade (matching the styles and rails), secured within styles and rails with specially designed solid foam PVC moulded beadings of required size using PVC solvent adhesive/ cement. The finished door shutter including SS hardware, 1 no. ss sliding bolt 200 x 10mm, 1 no. SS tower bolt 200 x 10 mm and 2 nos. SS handles 125mm, shall be fixed to frame with 3 nos. stainless steel hinges of minimum size 100x58x1.9 mm and stainless steel screws of required size complete as per direction of the Engineer-in-Charge. (Cost of above hardware is inclusive in rates) 5mm thick solid foam PVC panel of required size with moulded/ extruded beading of appropriate design shape and size as per manufacturer's specifications ( to secure the panel insert tight in place within the style and rails of shutter) matching the colour and shade of shutter frame. Decorative type.

Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

supplying, fitting and fixing 150X20X6mm L-type M.S clamp properly fishtailed, including maiking holes and setting as same in 250X125X75mm. Cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and direction of E/I.

Supplying fitting and fixing M.S.Grill made of 20x6mm M.S.flat as per approved design and drawing properly fabricated with joints continous fillet welded and finished smooth carriage of grill to work site,hoisting as per building specification and direction of E/I(where materials to not supplied by the deptt)

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for(i) Sites with basic wind speed 45 m/sec as per IS 875 — Part 3(ii) Sites with structure height more than 20m for all wind speeds Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.

Using R4 series with frame (115 mm & above) x (45 mm & above) & both glazed and fly screen sash (44 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated above) with zinc alloy (zamak) powder coated

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in roof members as pillers, plates, rafters, purlines. beams and type of beam with cost of nuts and bolts complete with cleats (with wooden check) fitting with screws all complete as per building specification and direction of E/I.

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 micronsminimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required.

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer- in-charge and as per manufacturer's specification, with all 4 sides tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. E/I.

Providing &Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone patter with anti algae and Uv resistace properties to be aapplied as intermediate fiish in desired pattern @ 43.04 kg/s10 sqm to form film of 1-1.15mm thickess after scrapping and propperly cleanig the surace to remove loose particles from the plaster surface,followed by top coating with premium acrylic smooth exterior paint with silicoe additives of required shade by two or more cots @ 1.43 litre/10sqm,complete as the direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over old wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing and fixing factory made PVC door frame of size 50x47mm with a wall lthickness of 5mm,mmade out of extruded 5mm rigid PVC foam sheet mitred at corners and join ed with 2nos of 150-mm lolng brackets of 15x15mm M.S.square tube,the bvertical door profiles to be reinforced with 19x19mmM.S.square tube of 19 guage EPDM rubber gasket weather seal to be provided through out the frame.The door frame to be fixed to the wall using M.S.screws of 65/100mm size complete as per manufacturers specification and direction of E/I.

Providin and fixing existing door frames 30mm thick factory made PVC door shutter made of style and rails of a UPSC hollow section of size 60mmx30mm and wall thickness 2mm+0.2mm with in built decorative moulding edging on one side.The styles and rails mitred and joined at the conrers by means of M.S.galvanised/plastic brackets of size 75x220mm having wall thickness 1.0mm and stainless steel screws the lock size 52x20mm and1mm+0.1mm wall thickness.The lock rail made of of ‘H’ section,a UPVC hollow section of size 100x30mm and23mm+0.2mm wall thickness fixed to the shutter frame filled with a UPVC multi chambered single panel of size not less than 620mm,having over all thickness of 20mm and1mm+0.1mm wall thickness.The panels filled vertically and tia bar at two places by inserting horizontally 6mm galvanized M.S.rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-chage.

Water proofing for Old and New Roof Slab:- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with. brush, roller or spray for water proofing coating as per manufacturer specifications with following steps: (a) surface preparation:-Providing and cleaning of concrete surface to remove dust, oil, grease Including removal of existing loose paint/ coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to Identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika India Pvt.Ltd. / MYK Schomberg Dr Fixit/Fosroc or equivallent. Providing and reparing of all corners and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150mm X 150 mm fillet of mortar (Cement: sands 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer. Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same withcement slurry including all material, labour, tools complete. (b)1st Coat Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application, 45 gsm of Fibre glass cloth to lay when the first layer is still green 1st coat should be applied @1.50 kg/SqmU/coat. For the AND purpose of measurement the entire treated surface will be measured." (c) 2nd Coat :-To apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the 1st coat over the glass fibre laid surface, 2nd coat should be applied @0,7 kg/ Sqmt/coat. For the purpose of measurement the entire treated surface will be measured." After three days of drying the 2nd coat, the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofing Brand:- Sika Topseal 109hl /Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2K/MYK Aquafin TG Product Performance- Chemical Base Part A: Acrylic copolymer, Part B: Specially graded cementitious powder- Density 1.6 kg/l (mixed density) at +27°C Tensile Strength - 2 N/mm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Strength -2 N/mm2 (concrete failure) (According to ISO 4624) Slant-Shear Bond Strength-4 N/mm2 (According to FIP 5.15) (According to ASTM D 2370) Elongation at Break -35% without Fibre Cloth and 20% with Fibre Cloth (According To ASTM D 2370) (d) Protection of treated surface with PCC The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1,5:3) with proper slope (1:120) towards the rain outlets in alternate panels of 2 mt x 2mt keeping 6 mm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 @ of 100 ml per bag of cement to be added in the screed concrete (paid separately for this items). All comers shall be just leveled with the screed concrete to ensure smooth discharge VERNMES of water-the peripheral gaps between pvc pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture Insensitive epoxy putty of Sika India Pvt.Ltd./MYK Schomberg / Dr Fixit/Fosroc .For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with Polysulphide Sealant. (Paid Separately). Brand- Sika India Pvt.Ltd. /MYK Schomberg/Dr Per M AND Fixit/Fosroc Warranty for five years.

covering of trreated surface with P.C,C .Providng 50mm thick cemet concrete M20(1:1.5:3)maintaing slope in alternate 2mtx2mt panels with approved quality of stone chips of 20mm to 6mm sizie graded and cleaned sand of F.M 2.5 to3 includig screening,shuttering and mixing cement concretein mixer with admixture of integral water proffing and placing in position,skirting curing,taxes and royalty all complete as per buidings specification and direction of e/I.panels that has been left should be casted next day.there should be 6mm gap between panels Brand sika plastocrate plus,MYK proof WP 10,FOSROC CONPLASTX421 ICX dR.fIXIT PIDIPROOF lW+-do-all complete job(old surface)

Providing fixing pressed steel door frame conferming to IS:4351 manufactured from commercial mild steel sheet of 1.60mm thickness including hinges,jamb,lock jamb,bead and if required angle threshold of mild steel angle section 50x25mm or base tiles of 1.60 mm pressed mild steel welded or rigidly fixed together by mechanical means including M.S.pressed butt hinges 2.5mm thick with mortar guards,lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as direction of E/I. Profile-C,Fixing with carbon steel galvanised dash fastener of requied dia and size Fixinng wih adjustable lugs with split end tail to each jamb)

Supplying, fitting and fixing 30mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer,over the plastered wall suface to prrepare the surface even and smooth complete.job as per direction of E/I.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm)

Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade of: old work (two or more coats applied @ 1.67ltr/10sqmm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, windows ,ventilator shutters and partitions etc with EPDM rubber/neoprene gasket etc complete as per the architectural drawings and the directions of E/I.(cost of aluminium snap beading shall be paid in basic item) with float glass panes of 4.0mm thickness(weight not less than 10kg/sqm)

Providing and fixing fly proof wire gauze to windows,clearstory windows& doors with M.S.flat 15x3mm and nuts & bolts complete stainless steel (grade 304) wire gause of 0.5mm dia wire and 1.4 mm aperture on both sides including all complete job.as per direction of E/I.

Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.

Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete

providing Tor steel reinforcement of 10mm,12mm,16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(8mm dia )

(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing and fixing 18mm thick Gang saw cut mirror polished, pre molded and pre polish machine cut for platforms, vanity counters windows sills, facials etc of required size shade colour, texture over 20mm thick base cement mortar 1:4(1 cement:4 coarse sand) with joints treated with white cement ,mixed with matching pigment, epoxy touch ups ,including rubbing, curing etc. complete at all levels. Granite any colour,area of slab over 0.50sqmm

Carriage of materials from nearest approved sources of supply including loading into trucks and unloading from trucks and stacking properly at work site as directed by the E/I.

sand lead 8K.M.

chips lead 22K.M.

Brick lead 8K.M(1K+7P)

local sand lead 3K.M

Stone Boulder 20 km lead

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(a) 580mm longwith 10.0 lit. low level P.V.C. cistern

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(b)10/12.5lit. low level P.V.C. cistern

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.

(B) Standing corner ( 600 mm x 350 mm )

Providing and fixing Chlorinated polyvinyl chloride (CPVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e. fixing the pipe with clamps at 1.m.spacing.This included jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(Internal work)(Exposed on wall)

20mm nominal outer dia pipes

32mm nominal outer dia pipes

50mm nominal outer dia pipes

Providing and fixing Chlorinated polyvinyl chloride (CPVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e. fixing the pipe with clamps at 1.m.spacing.This included jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(Internal work)(Concealeld work)

20mm dianominal outer dia pipes

25mm dianominal outer dia pipes

32mmdanominal outer dia pipes

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion(i)single socketed pipes.

75mm dia

110mm diameter

Providing and fixing on wall face unplasticised PVC moulded fittings, accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring confirming to I:5382 leaving 10mm gap for thermal expansion.

Single Tee with door

75x75x75mm

110x110x100mm

Bend 87’5

75mm dia

110mm

shoe(plain)

75mm dia

110mm dia

Providing and fixing on wall face unplasticised PVC pipe clips moulded fittings, accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring confirming to I:5382 leaving 10mm gap for thermal expansion.

75mm dia

110mm dia

S/F/F VIP Bath room fitting including all complete job as per direction of E/I.

pillar cock (Long neck)

Bib cock (Long tahread)

Bib cock(2 way)

Angular stop cock

Swan Neck Tap with left hand operating knob ISI Marked.

wall mixer with provision for over head shower with elbow coupling and wall flange

4-way diverterfor concealed fittings

Telephone shower with flexible pipe

Central Hole basin mixer(Best quality)

Towel Rail 24"

Towel Ring

soap dish

Thumbler Holder

Glass shelf 22"

Supplying fitting and fixing of Polycarbonate sheet approved quality including all complete job as per directionn of E/I.

Supplying fitting and fixing Jaquar Basin Mixer including all complete job as per direction of E/I. Gem Product ID: 5116877-4173547733

Supplying fitting and fixing Jaquar Bath Tub Mixer with Telephone shower including all complete job as per direction of E/I. Gem Product ID: 5116877-23265557697

Supplying fitting and fixing Jaquar Bib cock with wall Flange including all complete job as per direction of E/I. Gem Product ID: 5116877-4240710133

Supplying fitting and fixing Jaquar 2 way Bib cock with wall flange including all complete job as per direction of E/I. Gem Product ID: 5116877-92456303725

Supplying fitting and fixing JaquarSink cock w all mounted Model including all complete job as per direction of E/I. Gem Product ID: 5116877-2981119286

Supplying fitting and fixing Jaquar Angular stop cock with wall Flalnge including all complete job as per direction of E/I. Gem Product ID: 5116877-74826652122

Supplying fitting and fixing Jaquar Hand shower(Health faucet) including all complete job as per direction of E/I. Gem Product ID: 5116877-61545505248

Supplying fitting and fixing JaquarHand shower including all complete job as per direction of E/I. Gem Product ID: 5116877-58232913575

Supplying fitting and fixing Jaquar Shower Arm including all complete job as per direction of E/I. Gem Product ID: 5116877-26017138889

Supplying fitting and fixing Jaquar Over head shower including all complete job as per direction of E/I. Gem Product ID: 5116877-59935667070

Supplying fitting and fixing Jaquar Towel Ring including all complete job as per direction of E/I. Gem Product ID: 5116877-50047344331

Supplying fitting and fixing JaquarTowel Rail including all complete job as per direction of E/I. Gem Product ID: 5116877-42231658459

Supplying fitting and fixing Jaquar Soap Dish including all complete job as per direction of E/I. Gem Product ID: 5116877-85287194484

Supplying fitting and fixing JaquarBathroom Mirror Hanging including all complete job as per direction of E/I. Gem Product ID: 5116877-76230367352

Supplying fitting and fixing Jaquar P-Trap pattern 3 EWC including all complete job as per direction of E/I. Gem Product ID: 5116877-59437028766

Supplying fitting and fixing Jaquar Wash Basins Flat Back kand Rectanglle including all complete job as per direction of E/I. Gem Product ID: 5116877-95681183220

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)