University Of Jammu Tender

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints/ 20mm thick bed of coment mortar 600x600/300mm (morrocan type) (Sample to be approved by EIC)

Half brick masonry with bricks of class designation 75 in superstructure up to all floor levels In cement mortar 1cement: 4 fine sand mortar

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead.

Dismantling of existing wooden ceiling/partition including stacking of serviceable material and disposal of unserviceable material as directed with all leads complete.

15mm Cement plaster on the rough side of single or half brick wall of mix:1 : 4 ( 1 cement : 4 fine sand)

Removing white or colour wash by scrapping & sand papering & preparing the surface smooth including necessary repairs to the scratches complete.

Providing and applying POP punning to walls of avg. 1mm thickness to line level and plumb including surface preparation; required punning to be undertaken and completed in workman-like manner, to ensure desired finishing standards, as directed by EIC.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade two or more coats on old wood work including applying priming coat with ready mixed white,pink or grey primer of approved brand and manufacture including sand papering and knotting. (Sample to be approved by EIC)

Providing & fixing wallpaper of approved pattern & quality to wall surface including chemical & adhesive as per directions of EIC (Sample to be approved by EIC)

Providing and fixing of wooden paneling/ lining of 12mm (net thickness) including providing and fixing of ground frame work (50x25mm or as specified) of first class Budloo wood/ 19mm ply including cost of screws, wooden plugs etc. complete as per directions of EIC. made from export wood (Sample to be approved by EIC)

Touchwood polishing, two or more coats on wood work including pressing of nails, scrapping with emery paper, a coat of wood filler & fevicol washing complete as per directions of EIC on new wood work.

Aluminium Work . Providing and fixing Aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners ofrequired dia. and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, dashfastners, handles,hinges, all complete as per architectural drawings and the directions of Engineer in-charge. (excluding Glazing, sliding channels/ sliding arrangement and other fittings complete)Anodized aluminum (anodized transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Using 4"x1.75" sections 1.5mm thick INCLUDING 12MM thick prelaminated particle board

Providing and fixing glazing in aluminum door, window, ventilator shutters, and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminum snap beading shall be paid in basic item):With float glass panes of 5.00 mm thickness

Pantry counter with Granite Top, storage unit of any size with storage shall be made of 18mm pre-laminated plyboard with shutters as required including internal shelves with locking arrangements having 18mm granite fixed at top. Including 100mm concrete counter slab of mix 1:2:4 with shuttering and moulding complete

Providing and fabrication of ward robes (ornamental) of approved quality 19mm Ply Sheet (Ply to Ply) in sides, shelves and wherever required including 6mm ply wood on back and 19MM pine board ply wood in shutters, inside and outside of shutters finished with Dulmica sheeting of approved quality and color on exposed face of approved design and drawings including painting two or more coats of synthetic enamel paint of approved quality and color inside including cost of following aluminum fittings and locks of approved make.15mm dia. M.S. pipe chromium plated with necessary brackets 4'-0" length and including all other necessary accessories complete in all respects. Including fixing with dashfasteners wherever required (For payments front face to be measured).40-45 cm deep

Providing and fixing machine molded ACP covering of approved pattern & design, made out of machine cut aluminum sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia. and 75 mm long bolt including providing aluminum washers 2 mm thick & 15 mm dia. at a staggered pitch of 200mm Centre to Centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. Including frame work complete as per direction of Engineer-in-charge. ACP 3.5mm thick of required color

Providing and fixing 30-35 mm thick glazed shutters for windows and clearstory windows using 8.70kg/Sqm. (3.5mm thick) glass panes including black enameled ISI marked M.S. butt hinges with necessary screws. First. Class imported wood.

Providing and fixing of glass pans with wooden fillets of required size wherever necessary. Glass pans 3.5mm thick weighing 8.70 Kg / sqm.

Providing and fixing of water heater (geysers) (Havells/ Hindware/ Jaquar/ Venus or equivalent) including cost of dash fasteners with nuts and washers 50 litres

Providing and fixing of 15mm size chromium plated cast brass angle valve of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) with wall flange

Providing and fixing of 15mm size chromium plated cast brass wall mixer Non telephonic with lead of approved quality. (Hindware/ Jaquar/ Kerrovit/ equivalent)

Providing and fixing of 15mm size chromium plated cast brass wash basin mixer (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)

Providing and fixing of 15mm size chromium plated cast brass sink mixer (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)

Providing and fixing Salem stainless steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. 610x510mm bowl depth 200mm. (Sample to be approved by EIC)

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231, with fittings and fixtures complete. 10 liters capacity- white (Sample to be approved by EIC)

Providing and fixing of Soap Dish holder of approved quality and make.

Providing and fixing of floor trap of approved quality and make.100mm

Providing and fixing of C.P Grating of approved quality and make.100mm

Providing and fixing spindle 15mm dia. All types like washer type/disc type etc.

Providing & fixing curtain rod with brackets, knobs complete job

Providing and fixing of roller blinds of required pattern/color as approved by EIC including necessary fittings and fixtures

Providing and fixing of PVC connection with C.P. brass unions 450mm

Providing and fixing of PVC waste pipe

Providing and fixing of C.I. manhole cover heavy duty rectangular/ circular of required size

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-Part 1 : 2011 (Board with BIS certification marks)

Note. The quoted percentage (%age) should preferably be in fractional form in order to minimize concurrence of similar quoted rates