University Of Jammu Tender

Centering and shuttering including strutting propping etc. removal of form work in Suspended floors, roofs, landings, balconies, access plat forms, Lintels, beams, plinth beams, girders, bressumers, cantilevers, Columns, pillars, piers, abutments, posts and struts and edges of slabs etc. (M.S. Plates/Ply wood)

Foundation footings basis of columns etc. for mass concrete.

Brick work with FPS bricks of class designation 75 in super structure up to all floors. In cement mortar 1cement: 6 fine sand mortar.

Reinforcement of RCC works including straightening cutting bending placing in position & binding all complete mild steel & medium tensile steel bars

Providing and fixing pre-coated galvanized iron profile sheets/corrugated/tiled (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self-drilling /selftapping screws of size (5.5x55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required

Providing and fixing of planed eaves boarding 250mm x 30mm size of 1st Class imported wood.

Providing and fixing of ornamental cornice of following size. 1st class budloo/imported wood. 50-75mm

Providing and fabrication of storage almirah of approved quality of approved quality 19mm Ply board in sides, shelves and wherever required including 6mm ply wood on back and 19MM ply board in shutters, inside and outside of shutters finished with Dulmica sheeting of approved quality and color on exposed face of approved design and drawings including (painting two or more coats of synthetic enamel paint of approved quality and color inside) including cost of following aluminum fittings and locks of approved make. including all other necessary accessories complete in all respects. (For payments front face to be measured). 45-60cm deep

Providing and fixing of ply wood includingcost of nails adhesive etc. complete at all places.10-12mm

Half brick masonry with bricks of classdesignation 75 in superstructure up to all floor levelsIn cement mortar 1cement: 4 fine sand mortar

Providing & fixing of following sanitary cp items cera hindware jaguar kerovit or equivalent make 15mm nominal dia

LAB SINK

LAB sink mixer

soap case

PVCwaste pipe WITH CP WASTE

adapters 25mm

Providing and fixing of PVC Prince pipe (Type “B”) in proper gradient in excavated trenches including jointing and refilling the excavated material complete including cost of excavation. 75mm

Providing and fixing of the following PVC fittings. (Prince Make)100mm floor trap including p&f of cp grating 100mm

Construct brick masonry man hole in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 Coarse sand : 4 graded stone aggregate 20mm nominal size) foundation concrete (1:4:8) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size finished with a floating coat of neat cement complete.) Inside size 45cm x 45cm x 45cm deep depth varies as per the slope including C.I. manhole cover medium duty with frame of size 45x45mm size. With F.P.S. bricks /concrete slab with class designation 75 and with crushed stone aggregate complete in all respects.

Providing & fixing of ppr ball valve of standard make 25mm

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings, adaptors etc. This includes testing of joints complete as per direction of Engineer incharge. Internal work Concealed fixing the pipe etc. (Sample to be approved by EIC) including all types of adapters 25mm

Providing and laying vitrified floor/ wall tiles of size 600x600mm in floor 600x300 in wall or as directed (thickness to be specified by the manufacturer) approved make in all colors, shades as approved by engineer- in-charge laid on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) including pointing the joints with matching pigment or any other relevant pigment as directed including cleaning the floor after finishing of work including spacers (Sample to be approved by EIC)

Providing and fixing 18mm thick mirror polished, machine cut for floors, kitchen platform, vanity counters facieses and other similar locations of required size of approved shades, color and texture laid over 20mm thick base cement mortar 1:4 (1cement: 4 coarse sand) and joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. complete at all levels. Black Granite as approved by EIC

12mm thick cement plaster on half brick / concrete wall of mix 1:6 (1cement: 6 coarse sand)

Dismantling/chipping of old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead.

Dismantling of existing wooden ceiling /walling including stacking of serviceable material and disposal of unserviceable material as directed with all leads complete.

Demolishing brick work in cement mortar up to floor V level including stacking of serviceable material and disposal of unserviceable material within the campus as per directions of EIC.

Dismantling of existing window shutters carefully without breakage including stacking within a lead as directed by the in-charge engineer.

Engagement of plumber/Carpenter/helper for various miscellaneous works

Carpenter

Plumber

Helper

Wall painting with plastic emulsion paint (two or more coats) of approved brand and manufacture to give an even shade. New work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new wood work/plastered surface including sand papering, knotting and a coat of primer complete

Finishing with exterior acrylic paint of approved brand and manufacture (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete on all surfaces. New work including appropriate priming

Providing and fixing Aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia. and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, dashfastners, handles, hinges, all complete as per architectural drawings and the directions of Engineer-in-charge. (excluding Glazing, sliding channels/ sliding arrangement and other fittings complete) but including 12mm thick prelaminated particle board Powder coated aluminum (minimum thickness of powder coating 50 micron) Using 2.5"x1.5" sections 16 Gauge thick

Extra for using 5mm float glass instead of 12mm thick prelaminated particle board

Providing and Fixing factory made standard quality glazed uPVC casement/sliding window , made of extruded profiles. frame shall be of size 50 X 50 mm (extruded profile duly reinforced with 1.60±0.2mm thick Galvanised mild steel sections) with glazing bead 12 x 18 mm Casement Frame (67 mm x 62 mm) Casement Window Sash / Mullion (67 mm x 75 mm ) (style, rail and intermediate section) Casement Glazing bead (35 mm x 18 mm). Profiles of frames and sash will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in-charge. Providing & fixing factory cut/processed mechanically sealed composite glass (configuration 6 mm thick toughened outer glass + 12 mm thick air gap + 6 mm thick toughened inner glass) with performance parameters of the composite that meet the given acceptable value ranges as follows: Visual Light transmission % (VLT) 15 - 50; External reflectance 5 - 25; Solar factor (SF) or Solar Heat Gain Coefficient (SHGC) 0.2 - 0.38; U value .5 - 1.5 W/sqm.K. R Value 2.86, Colour of glass to be clear/neutral/grey/blue as approved. Make Asahi/Saint Gobain or equivalent up to all floor levels (Vendor to specify the make and name of products considered for quotation. The price should include the cost of wastage, obtaining correct measurement, preparing the glass assembly including cutting, toughening, sealing, mastic, dessicant treatment, etc. complete).Including all hardware fittings using high quality locking mechanism as per architectural drawings and approved by Engineer in-charge. (For glazing only toughened glass be used)

Providing and fixing wood work in frame work / joists of false ceiling, partitions, joists etc. sawn and put up in position.First. Class imported wood.

Providing hoisting and fixing trusses / purlins / rafters / posts, post plates, in planks and any sort of work or like components, including cost of screws nails etc. complete.First. Class imported wood.

Chemical wash treatment for vitrified floor tiles to make it clean complete as per the direction of EIC

Providing and fixing of duct pipe (laboratory environment) 8" round or as required. It should be made of material suitable for chemical exhaust including making holes in the wall for laying of the pipe or as required and directed by EIC on site

Note. The quoted percentage (%age) should preferably be in fractional form in order to minimize concurrence of similar quoted rates