University Of Jammu Tender

Structural steel work welded in built up sections, trusses and frame work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer including applying two coats of paint all complete in angles / flats / tubes / channels etc

Providing & fixing G.I chain link fabric fencing of required width mesh size 50x50mm intcluding strengthening with 2mm dia wire or nuts bolts & washers as required complete as per direction of engineer in charge made of G.I wire of 4mm dia including applying one coat of priming coat & two coats of synthetic enamel paint complete in all respects

Dismantling/Demolishing. Dismantling of existing chain link fencing, steel work complete, including stacking of serviceable material and disposal of unserviceable material within a lead as directed.

Engagement of blacksmith & helper for repairing G.I chain link fabric fencing of required width mesh intcluding strengthening wire or nuts bolts & washers as required complete as per direction of engineer in charge including applying one coat of priming coat & two coats of synthetic enamel paint complete in all respects

Engagement of blacksmith & helper for repairing Structural steel work welded in built up sections, trusses and frame work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer including applying two coats of paint all complete in angles / flats / tubes / channels etc.

Chipping of old plaster complete in all respects as directed by EIC including disposal of excess within lead as directed and cleaning the area

12mm thick cement plaster on half brick / concrete wall of mix 1:6 (1cement: 6 coarse sand)

Demolishing cement concrete work, including disposal of unserviceable material within the campus as per directions of EIC 1:3:6 or richer mix.

Brick work with FPS bricks of classdesignation 75 in super structure up to all floors.In cement mortar 1cement: 6 fine sand mortar.

Providing and laying polished vitrified floor tiles of size 600x600mm (thickness to be specified by the manufacturer) approved make in all colors, shades as approved by engineer- in-charge laid on chemical (Tilofix) of required thickness including pointing the joints with matching pigment or any other relevant pigment as directed including cleaning the floor after finishing of work including spacers as directed (Sample to be approved by EIC)

Providing and layingchequered vitrified floor tiles of size as reqd (thickness to be specified by the manufacturer) approved make in all colors, shades as approved by engineer- in-charge laid on chemical (Tilofix) of required thickness including pointing the joints with matching pigment or any other relevant pigment as directed including cleaning the floor after finishing of work including spacers as directed (Sample to be approved by EIC)

Providing and fixing 18mm thick mirror polished, machine cut for floors, kitchen platform, vanity counters facieses and other similar locations of required size of approved shades, color and texture laid over 20mm thick base cement mortar 1:4 (1cement: 4 coarse sand) and joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. including moulding complete at all levels. Granite of any color as approved by EIC

Demolishing brick work in cement mortarup to floor V level including stacking of serviceable material and disposal ofunserviceable material within the campusas per directions of EIC

Supplying and laying of stone soling hand packed tightly including ramming, watering and carriages complete.

Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering. All work up to all levels. 1:2:4 (1Cement: 2 coarse sand:4 graded stone aggregate 20mm nominal Size) Crushed

Providing and fixing machine molded ACP covering of approved pattern & design, made out of machine cut aluminum sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia. and 75 mm long bolt including providing aluminum washers 2 mm thick & 15 mm dia. at a staggered pitch of 200mm Centre to Centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. Including frame work complete as per direction of Engineer-in-charge. ACP 3.5mm thick of required color

Providing and fixing Tiled/GRID falseceiling of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitablyspaced joints to get required length and ofsize 24x38 mm made from 0.30 mm thick(minimum) sheet, spaced at 1200 mm center to center and cross “T” of size24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spacedbetween main “T” at 600 mm center to center to form a grid of 1200x600 mm andsecondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mmthick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to formgrids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying falseceiling tiles in the grid including, required cutting/making, opening for services likediffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners tobe suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GIadjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mmspaced at 1200 mm center to center along main T, bottom exposed width of 24 mmof all T-sections shall be pre-painted with polyester paintpaint, all complete for allheights as per specifications, drawings and as directed by Engineer-in-charge.2 GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizingof100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia

Painting with synthetic enamel paint ofapproved brand and manufacture of required color to give an even shade .one or more coats on old wood/plaster work.

Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade. one or more coats on old steel work

Steel work in built up tubular (round,square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting ,fixing in position and applying a priming coat of approved steel primer, includingwelding and bolted with special shaped washers etc. complete.Hot finished welded type tubes& one coat of priming coat & one or two coats of paint as directed by EIC

Repair of stainless steel (Grade 304) railing including removing, straightening, refixing the missing members, bolting, welding wherever necessary. SS member wherever required is included in the cost.

Finishing with exterior acrylic paint of approved brand and manufacture (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete on all surfaces. New work including appropriate priming

Providing and fixing of glass pans with wooden fillets of required size wherever necessary.lass pans 3.5mm thick weighing 8.70 Kg / sqm.

Repairs/Dismentling of Aluminium Doors/ Windows partition including cost of necessary beading, fasteners, screws, rubber gaskits complete

Wall painting with plastic emulsion paint (one or more coats) of approved brand and manufacture to give an even shade. Old work

Providing and fixing wash basin (Cera) white vitreous china wash basin size 630x450mm with pedestal including waste pipe

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) one piece with seat and lid, 10 liter low level white PVC flushing cistern with manual controlled device (handle lever) confirming to I.S. 7231with all fittings and fixtures complete including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid. ((Jaquar/ Hindware/ Cera/ Kerrovit or equivalent)

Providing & fixing of following sanitary fittings of standard quality make (Sample to be approved by EIC)

sink

health faucet with chain

bib cock

pvc connections

looking mirror

angle valve

element

thermostat

Providing and applying cemement basedwall putty 1mm thickness over plastered surface to prepare the surface even and smooth complete

Note. The quoted percentage (%age) should preferably be in fractional form in order to minimize concurrence of similar quoted rates