University Of Jammu Tender

Providing and laying in position reinforced cement concrete 1:1.5:3 (1 cement 1.5 coarse sand 3 graded crushed stone aggregate 20 nominal size including cost of centering, shuttering complete. All work upto plinth level.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form work for: Retaining walls, return walls, walls (any thickness) including attached pilasters buttresses, plinth and string course fillets, kerbs and steps etc

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms.

Providing steel thermo mechanically treated bars conforming to IS:45612000 reinforcement for all RCC work including bending, binding and placing in position complete including cost of cold twisted steel reinforcement and binding with 18-20 gauge, soft drawn concealed steel binding wire complete as per specifications and drawings(upto height of floor V level). Fe 500 D

Brick work with 2nd class bricks of class designation 75 in foundation, plinth & in Superstructure in cement mortar 1:6 (1 cement : 6 coarse sand) upto floor V level.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : Sal wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing ISI marked flush door shutters non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters :35 mm thick including ISI marked anodised aluminium butt hinges with necessary screws.

Providing and fixing powder coated 50 microns aluminum work (10 gauge) for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, metered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. For frames and shutter of door windows & ventilators/Sliding shutters including providing and fixing hinges/pivots, handles, tower bolts, eye hooks/window stays, including the cost of PVC/neoprene gasket 5mm glass panes/12mm laminated board on both sides, hydraulic door machine where ever required complete job as required. The Spacing of Vertical members not to exceed 4’-0” & section to be used is 104 mm x 44.45 mm

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement : 4 coarse sand) ( Exterior / Interior Work)

Providing and laying 600 x 600 mm vitrified floor tiles in 600 x 600 mm sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 Cement: 4 coarse sand) including grouting the joints with cement and matching pigments etc complete.

"Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. "

Supply & fixing of nut & bolts with washers of size ( 50mm x 4mm / 80mm x 6mm) as required.

Making holes in angle iron for fixing Sal wood & then Ply-wood

Providing and fixing 18mm thick 710 grade waterproof / termite proof plywood for fixing to M.S steel frame with nuts bolts and washers, excluding cost of nut bolts and washers. Nothing extra on account of wastage shall be paid

Providing and fixing teak wood lipping of size 25x3mm in pelmet/ plywood edges

Applying priming coat :With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work

Applying white cement based Putty of average thickness 1mm of approved brand & manufacture on wall surface to give an even finish .

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Providing and fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete: 250x10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125 mm

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. Complete

10cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa at 35kg per cum of earth and gobri leaping with mix 1:1 (1 clay: 1 cow dung) and covered with specified tile bricks grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finishing neat. With common burnt clay (non modular) brick tiles of class designation 10.0

Providing and laying APP (Atactic Poly Propylene Polymer ) modified prefabricated five layer water proofing membrane, black finishing reinforced with glass fibre mat consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sq. mt. by the same membrane manufacture of density at 25°C, 0.87- 0.89 kg/ltr and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under: Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorized applicator of the manufacture of membrane. 3 mm thick water proofing membrane with non-woven polyester matt: Joint strength in longitudinal and transverse direction at 23°C as 650/450 N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N.

Providing gola (Angular Fillet) 75 x75mm in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase

Making khurras 45x45cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20mm nominal size) over P.V.C. sheet 1mx 1mx400 micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edges and making the finishing outlet complete.

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diameter

Providing and fixing un-plasticised -PVC pipe clips of approved design to un-plasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

Supply of Labour for different works ( to be paid actual engaged at site ) a. Mazdoor

Supply of Labour for different works ( to be paid actual engaged at site ) b. Carpenter II class