University Of Jammu Tender

Brick work with common burnt clay Non-Modular bricks of class designation 75. in Super structure above plinth level including curing complete in Cement mortar 1:6 ( 1 cement : 6 coarse sand).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Sal wood.

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class teak wood.35mm thick

Providing and fixing aluminium sliding door bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 150x10 mm

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper

Providing and fixing Aluminium handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS 1868 ) tranparent or dyed to required colour or shade with nuts and screws etc. complete 125mmn

15mm Cement plaster on the rough side of single or half brick wall of mix 1 : 4 ( 1 cement : 4 fine sand).

Engagement of Labours for different works Mazdoor

Blacksmith Second Class

Providing and applying white cement based putty of specified thickness,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1mm Thick.

Distempering with 1st quality acrylic distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer.

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg /10sqm).

Providing and fixing PVC pipe of 4KG pressure of Approved Brand and manufacture including cost of 1:2:4 Mix Concrete (Make Finolex/Prince/Supreme). A. 150mm Dia

b. 75mm Dia

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.In all colours, shades, except White, Ivory, Fume Red Brown.

Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. completeSize of tile 600x600 mm

P/F solid plastic seat with lid for pedestal type W.C. pan complete (Parry ware /Hind ware/ /Cera)White colour

P/F low level PVC flushing cistern with manually controlled device (handle lever) conf. To IS: 7231 with fitting & fixtures complete (Parry ware / Hind ware /Cera) 10 Liter Capacity – White.

P/F white vitreous china wash basin including making all connection but excluding the cost of fitting Flat Back W/basin(of size 550 x 400mm) (Parry ware /Hind ware/ Cera) of superior glass

P/F mirror, thickness of req. shape and size with plastic moulded frame of approved make and shape with 6 mm thick hard board backing Rectangular Shape 453x357 mm.

P/F of C. P. Pillar cock Make 15 mm (nominal size).

P/F CP brass bibcock of ‘Parryware/Jainco/Cera Make’ 15mm nominal bore

P/F CP brass angle valve for basin mixture Geyser points/washbasins 15mm nom. Bore

P/F of PVC waste pipe for sink or wash basin including P.V.C. waste fitting complete Semi Rigid Pipe 32/40 mm

P/F C.P Grating 100mm dia Circular Type.

P/F of unplasticised PVC connection pipe with bass union 45 cm length & 15 mm nom. bore.

P& F CP jet with PVC pipe to be fixed with WC.

Providing and fixing C.P towel rail including end brackets cost of wooden/PVC plugs with screw complete of size 600 x 20 mm of approved make.

Providing and fixing C.P soap dish of approved quality and make.

Providing and fixing white vitreous china pedestal type (European type/wash down type) water closet pan.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work-Exposed on wall 15 mm dia. nominal bore. 15 mm dia nominal bore.

20 mm dia. nominal bore

25 mm dia. nominal bore

Providing and fixing PVC Fittings of approved make (Make Finolex /Prince/ Supreme). 100mm Dia Bend

75mm Dia Bend

100 to 75mm Dia Floor Trap

TEE 110mm

COWl 110mm

Door Bend 75mm

Door Bend 110mm

TEE 75 mm

Providing and Fixing Ball Valve with handle lever of approved Brand and manufacture ( Make DRP /Ship). 15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

Providing and Fixing Hand Jet Of approved Brand and manufacture ( Make Hindware/ Parryware/ cera/ Jaguar).

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work).15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing 35mm thick ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.22.1 With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. (Double Shutters).

Renewing glass panes, with wooden fillets wherever necessary : Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm)

Providing and fixing powder coated 50 microns aluminum work (10 gauge) for doors, windows, ventilators, Almirahs and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, metered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. For frames and shutter of door windows, ventilators & Almirah including providing and fixing hinges / pivots, handles, tower bolts, eye hooks/window stays, including the cost of PVC/neoprene gasket, 5mm glass panes / 12mm thick particle board laminated on both sides, locks of superior quality including P&F of Double Action Hydraulic door closer/floor spring of approved brand and manufacture IS:6315 with stainlees steel cover plate minimum 1.25 mm thickness. The spacing of vertical/horizontal members not to exceed 4 feet and the section to be used shall be 101mm x 44.45 mm.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete Fixed to openings / wooden frames with rawl plugs screws etc.

Labour Engaged for Removing of Dismentalled material from site to outside of University Campus including cost of loading and unloading complete lead upto 10km outside muncipal limits.

Providing and fixing tiled False Ceiling of specified materials of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120gms /sqm both side inclusive ) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200 x 600mm and secondary cross “T” of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting /making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (The rate is excluding the cost of tiles which will be paid for separately). GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms /sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).