Small Scale Industries Development Corporation Limited Tender

Assistant Professor: 6HP

Jt. Director: 8 HP

Commercial Complex: 8HP

EVAPORATIVE VRF INDOOR UNITS Supply, Installation, Testing and Commissioning of variable refrigerant flow modular type indoor units comprising of all accessories as per the specifications. The indoor units shall be suitable to work on cooling as well as heating mode. The indoor units shall be suitable for operation on 220±6% /415±6% volts, 50Hz, 1/3 phase AC power supply. Ductable indoor units shall be suitable to handle extent of ductwork as shown in the design drawings and and the indoor units shall be of following capacities: Make : Mitsubishi Heavy/ Toshiba /OGeneral .

Assistant Professor: Ducted Units 3.0 HP

Assistant Professor: : Hi Wall Units 2.0 HP

Jt. Director: Ducted Units 3.0 HP

Jt. Director: Hi Wall Units 2.0 HP

Commercial Complex: Ducted Units 3.0 HP

Commercial Complex: Ducted Units 3.0 HP

Commercial Complex: Hi Wall Units 2.0 HP

Supply installation , testing commissioning of INSULATED REF JOINTS / Y-JOINTS, CONTROL BOX, SPLITTERS, PIPE FITTINGS, headers, ACCESSORIES ETC. for all the above VRF IDU/ODU units. complete with all accessories

Corded/Cordless Remote for Indoor units

CENTRAL CONTROLLER With PC Monitoring Systems - Centralised Control Compliant Manager/ Smart Manager including all Hardware/Software system, USB Adaptors, Telephone Line connectivity, Allied cabling between centralized control system with Outdoor/Indoor units and other allied accessories , etc complete job. System should have facilities for start, stop,temperature setting,fan speed control,mode control,Group control,emergency start & stop, BMS access and fault Diagnosis. Make : Mitsubishi Heavy/ Toshiba /OGeneral .

REFRIGERANT PIPING- (If required at site) Supply, Installation, Testing & Commissioning of high pressure copper refrigerant piping suitable for R 410a refrigerant of suitable size as required and duly insulated with 19mm/13mm thick closed cell elastomeric insulation in tubing form. External Refrigerant piping shall be laid on GI cable trays. Refrigerent pipes on terrace or platform shall be installed on raised GI Cable tray and finally covered with GI Sheet Cover for protection. Piping inside occupied spaces shall be supported using MS hangers duly painted with black enamel paint. Entire refrigerant piping work be carried out in accordance with the specifications. Piping shall be of following sizes :

6.35 mm dia with 13mm thick nitrile rubber insulation

9.53 mm dia with 13mm thick nitrile rubber insulation

12.7 mm dia with 13mm thick nitrile rubber insulation

15.8 mm dia with 13mm thick nitrile rubber insulation

19.0 mm dia with 13mm thick nitrile rubber insulation

22.2 mm dia with 19mm thick nitrile rubber insulation

28.6 mm dia with 19mm thick nitrile rubber insulation

31.8 mm dia with 19mm thick nitrile rubber insulation

34.9 mm dia with 19mm thick nitrile rubber insulation

41.1 mm dia with 19mm thick nitrile rubber insulation

PVC DRAIN PIPING Supply, installation, testing and commissioning of rigid PVC piping complete with fittings, supports as per specifications and duly insulated.

50 mm dia

40 mm dia

32 mm dia

25 mm dia

20 mm dia

GSS DUCTING (If required at site) Supply, installation, testing and commissioning of Sheet metal ducting 24 Guage Ducting

DUCT THERMAL INSULATION (If required at site) Supply, installation and testing of External Thermal insulation on ducts covered with closed cell crosslinked polyethylene foam having density 25-30 with/without self adhesive as per the approved specifications. 9 mm thick Insulation

DUCT ACOUSTIC LINING (If required at site) Supply, installation, testing and commissioning of acoustic insulation. Material shall be open cell nitrile rubber (with/without self adhesive) with 140-180 Kg/m3 density and all accessories as per specification. 15 mm thick linning

AIR TERMINAL DEVICES Supply, installation, testing and commissioning of grilles/ diffusers as per specifications and drawings excluding fixing frame of G.I./wooden in false ceiling/walls.

Aluminium Supply/Return Air Diffusers

Aluminium Supply/Return Air Grilles

Supply,Installation,Testing and commissioning of duoble layer canvas connection with 1/2 hr. fire rating as per specification.

GI CABLE TRAY Supply and installation of lader type GI 'U' shaped channel cable tray of following sizes. 40 x 300 x 40 x 2 mm

CONTROL & TRANSMISSION WIRES

Supply, installation, testing and commissioning of control cum transmission wiring of 2 core x 1.5 sqmm copper cable between indoor and out door unit including conduit pipes

Supply, installation, testing and commissioning of control cum transmission wiring of 2 core x 4 sqmm copper cable between Control Panel and Outdoor/Indoor units including conduit pipes

Supply, installation, testing and commissioning of control cum transmission wiring of 2 core x 2.5 sqmm copper cable between Control Panel and Outdoor/Indoor units including conduit pipes

MS STANDS Supply, fabrication and Installation of MS base frame/Platform for Outdoor Units duly painted (Job includes ODU/IDU, Refrigerant piping, Ducting, etc)

6 HP ODU Stand

8 HP ODU Stand

ELEVATOR Assistant Professor, Joint Director, Staff Qtr. Type 1, Staff Qtr. Type 2, Staff Qtr. Type 3 TYPE & CAPACITY: MRL Gearless Pasenger Elevator, Approximately 680 Kg., 10 persons Speed 1.0 Mps Type of Drive: A.C. Variable Voltage Variable Frequency with Microprocessor. Location of Machine-room:Machine Room Less Serving: 4 Floors 4 Stops 4 Openings 4 Levels [All on the same side] Car Enclosure:Constructed out of Stainless Steel Honeycomb Finish Car Panels. Car Entrance:Center Opening Automatic Framed Stainless Steel Honeycomb Finish Hoistway Entrance: Center Opening Automatic Framed Stainless Steel Interlock Finish. Door Operation: Center Opening Automatic doors. Control: Simplex Full collective operation With / Without Attendant. Power Supply: 415 Volts, 3 Phase, 50 Hertz Alternating Current Fan:Ventilation Fan. Flooring: Granite Flooring by Customer. 20 mm Recess will be provided by supplier. Lighting: Diffused LED Lighting in car/Eq. Indicators: Digital Direction and Position Indicators in both car and at all landings. Battery Operated Emergency Light with Rechargeable Battery. Micro Movement L.E.D. based Buttons. Hands Free Press and Speak Intercom The job includes Warranty/Maintenance: 1 Year warranty & 5 Years AMC System Capable of withstanding +10% to –10% Variation in Supply Voltage Fluctuations. Full Height Infrared Safety Curtain with Minimum 150 Intersecting Beams. Stainless Steel False Ceiling in Mirror Finish. Pit Ladder. Automatic Rescue Device to automatically bring the elevator to a landing in case of power failure and Controller Failure Load Weighing Device with Overload By - pass Feature. All Signal Fixtures will be in Stainless Steel Face Plates. Shaft Lights Makes: OTIS Elevators (India) Ltd. / Mitsubishi/Kone Elevator India Pvt. Ltd./ Thyssen Krupp/ Schneider

No. of Lifts

Fire Fighting System Non Schedule Items Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all accessories as per manufacturer's specifications. (Note - The Supply and Installation of all the items will be done as per the actual requirements at site)

ABC dry powder stored pressure type 6 kg capacity (IS:15683).

CO2 gas nozzle type - 9 Litre capacity (IS:2878).

Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683).

Providing and fixing 18 mm traventino beige Italian Marble cladings upto 10 Mtr.Ht. with Dash Fastners & filling of holes special adhesive like araldite or equivalent chemical over 12mm thick bed of cement mortar 1:3 (1 cement : 3 corase sand) including painting in white cement with an admixture of pigment ot match the stone shade of any colour and shade Complete Job .As per the specification/selection by Architect

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

"Providing & Fixing of Lay in Std Perforated metal ceiling System consisting of 600x600x0.5mm Lay in tiles of pre coated galvanised steel in 0.5 mm thickness in white colour with standard perforation of 2.5mm dia & open area of 20% and having black fleece acoustical fleece glued to the back of the tile to be laid on OEM grid systems with 15mm wide T - section flanges colour white having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees. The tiles should have Humidity Resistance (RH) of 100%, NRC of 0.70, Fire Performance A2-s1.d0 in module size of 600 X 600 mm, suitable for Green Building application, with Recycled content of 25%. Make : Armstrong or Equivalent. specificiations/selection done by Architect. The grid should be of OEM make with 15mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm and a load carrying capacity of 23.71 Kgs/M2. The T Sections have a Galvanizing of 120 grams per M2 & passed through 500 hrs of Salt test. The Tile & Grid system used together should carry a 15 year warrantee. OEM (ORIGINAL EQUIPMENT MANUFACTURE) INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit using OEM suspension system (specifications below) at 1200mm maximum centre. The First/Last OEM suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be OEM wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres. OEM SUSPENSION SYSTEM accessories manufactured and supplied by OEM consisting of M6 Anchor Fasteners with Vertical Hangers made of Galvanised steel of size 26 x 26 x 25 x 1.2mm with a Galvanised Thickness of 80gsm, A p+C560re Straightened Hanger wire of dia – 2.68 mm of 1.83 m length., thickness of 80gsm and a tensile strength of 344-413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanised spring steel for 2.68 mm with a minimum pull strength of 110 kg. The adjustable clip also consists of a 3.5 mm aquiline wire to be used with the main runner.specificiations/selection done by Architect. (in Recreation & Common Room)"

"Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board.Make: Armstrong, lagyp or equivalent. As per the specification/selection by Architect."

Part - B (Electrical & allied works)

Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium duity PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc. as required. GROUP A

Supplying and fixing single pole blanking plate in the existing modular plates complete etc. as required (MAKE Panasonic LEGRAND,L&T HAGER,INDO ASIAN & HPL).

Supplying and fixing following way, surface/recess mounting, vertical type 415 volts, TPN MCB Distribution board of sheet steel , dust protected duely power poainted inclusive of 200Amp tinned copper busbar, common neutral link, earth bar, dinbar for mounting MCB's (but withoit MCB'S and incomer) as required (note vertical type MCB TPDB is normally used where three phase outlets are required).(Make legrand, L&T, hager, IndoAsia and HPL) A) 8 WAY(4+24 way), double door

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.(make Legrand, L&T, Hager, IndoAsian & HPL). 63 Amp

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. (MAKE LEGRAND,L&T HAGER,INDO ASIAN & HPL) 63 Amp

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm

Providing and making earthpits including the cost of 300 mm x 300 mm all earth work, masonry enclosure with CI FRLSame & cover plate having locking arrangement complete as per IS 3043:1987 for body earth

Supply and laying 50mm x 6mm GI strip at 0.50 meter below ground as strip earth electrode including connection/ terminating with GI nut, bolt, spring, washer etc., as required (jointing shall be done by overpalling and ith 2 sets of GI nut bolt & spring washer spaced at 50mm)

Supply Installation testing & commitioning of Maintenance free hot deep galvienised on 250 microns GI Earthing system with 10 ft long , 80 mm dia & 3.0mm wall thickness. (Pipe-In-Pipe with Flat Terminal ) Tecnology.with 2 Bag of Electron High Conductive & Anti Corrosive Compound Spec : 3 mtr Length x 80 mm dia/ 2.96 mm thick / 250 micron Electrode Thickness : 3.0 mm / ISI Class - B, Hot Dip Galvanised 250 Microns Terminal size should be 40 x 10 mm thick (For use : All Body Earthing) with - CPRI ,ROHS,& Soil Resistivity test certificate. (LT panel HT panel HT meter, two pole and buildings sub panel

SH-V (PANELS) LT PANEL (TTA Design as per IEC 61439 - 1/2) Make: (Lengard XL-3/ Schneider - Blokset/ ABB - MNS OEM) Design, fabrication, assembly, wiring and supply, installation, testing and commissioning of front operated cubicle type compartmentalised, front access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for fault level of required value symmetrical at 415 volts, fabricated from 2 mm thick CRCA MS sheets for load bearing and 1.6mm for non load bearing with multi fold design, hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks and including GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. The panels shall be internal Arc tested. INCOMING: 2 Nos. 2000A, 415V, Icu = 45kA, 4P EDO ACB with Microprocessor based release ( MPR-1H or equivalent) having , Over current 40%-100% - Time setting,Selective short circuit 60%-1000% - Time setting ,instanteneous short circuit 150%-1500% , Under voltage time setiing 60%-95% Over voltage time setting 105 % -120% residula Voltage 10%-20% time setting EARTH earth fault with adjustable setting 20%-100% , Master Trip Relay Over Voltage & Under Voltage, Reverse power relay, Single phase preventer protection. REF protection 25 KVAR Capacitor with 63A MCCB 50 KA. ( transformer) 3 Nos. 1250A, 415V, Icu = 45kA, 4P EDO ACB with Microprocessor based release having , Over current 40%-100% - Time setting,Selective short circuit 60%-1000% - Time setting ,instanteneous short circuit 150%-1500% ,EARTH earth fault with adjustable setting 20%-100% , Master Trip Relay Over Voltage & Under Voltage, Reverse power relay, Single phase preventer ,( Release to be coordinated with the DG controller Those feature are available in the controller can be deleted from incomer) 1 Nos. 400A, 415V, Icu = 50kA, 4P MOTORISED MCCB with Microprocessor based release having , Over current 40%-100% - Time setting,Selective short circuit 60%-1000% - Time setting ,instanteneous short circuit 150%-1500% ,EARTH earth fault with adjustable setting 20%-100% , Master Trip Relay Over Voltage & Under Voltage, Reverse power relay, Single phase preventer ,( Release to be coordinated with the DG controller Those feature are available in the controller can be deleted from incomer) Nos. 0-500V Digital type Voltmeter with selector switch. 2 Nos. 0-400A Digital type Ammeter with selector switch with CT's 400/5A 3 Nos. 0-1250A Digital type Ammeter with selector switch with CT's 1250/5A 1 Nos. 0-2000A Digital type Ammeter with selector switch with CT's 2000/5A 6 no. PS class CT's 2000/5A for the protection 12 no. PS class CT's 1250/5A for the protection 3 no. PS class CT's 400/5A for the protection 6 Nos. Digital type Multifunction Meters to show KWH, KVAH, P.F. and Frequency 6 Set of phase indicating lamps with MCB protection. 6 Set of indicating lamp to indicate OPEN, CLOSE, TRIP.SPRING CHARGE. RYB PHSE INDICATING LAMPS Busbars: 3000A TPN busbars of aluminium alloy. 630A TPN busbars of aluminium alloy. MINI PLC for Auto load management and coordination for the Auto synchronizing though DG controllers 3no. 750 KVA, 1 NO. 250 kva with on off the breaker for 2 no. transformer and 3no, of the Bus copular according to the logic ( synchronizing shall be done by the DG controller) panel builder should coordinate with the DG vendor forinputs in the Mini PLC PLC SYSTEM: PLC system synchronisation and AMF logic for 5 DG sets and control of two no. Grid supply feeder complete with following accessories for auto load sharing /management / synchronising for D.G. Sets and control and interlocking as per scheme in SLD including control wiring for the system. Engine cranking relay , Indicating lamps, Push buttons with elements, Auto / manual selecter switch Battery charger, DC Ammeter, DC voltmeter, 8 point alarm annuniciator, Hooter

Auxiliary contractors, Control MCBS , Double voltmeter (134 mm Sq) analog , Double frequency (134 mm Sq) analog , Synchroscope (134 mm Sq), 60W, 240V AC GLS Bulb, 5A, Brass baten holder, Synchronising ON/OFF switch , Set selector switch , PLC/Manual selector switch , Push buttons with elements, Auxillary relays, Motorised potentio meter, Phase angle transducer , Voltage raise/lower joystick , Speed raise/lower joystic , Check synchronising relay 5 DG programmable logic controller (power monitor 33100 based) window based grafix software+others accessories and controls. Power Supply UPS - 2KVA with maintenance free batteries, charger etc. for 10 minutes backup. - 1 No Computer pentium-4 80GB hard disc., colour monitor + colour printer - 1 Set Any other relay/control/meter /System whether meintioned or not but required for successful/efficient operation of the system shall also be included. 1 no. Ventillating fan in PLC Panel Compartment Outgoing: 2Nos. 1250A, 415V, Icu = 50kA, TPN MDO ACB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. 5Nos. 630A, 415V, Icu = 50kA, TPN MCCB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. 7Nos. 400A, 415V, Icu = 50kA, TPN MCCB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. 2Nos. 200A, 415V, Icu = 50kA, TPN MCCB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. 2Nos. 160A, 415V, Icu = 50kA, TPN MCCB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. 5Nos. 100A, 415V, Icu = 50kA, TPN MCCB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. 1Nos. 800A, 415V, Icu = 50kA, TPN MCCB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB.with one no. change over switch ( For Fire Pump) 2Nos. 125A, 415V, Icu = 50kA, TPN MCCB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. 2Nos. 200A, 415V, Icu = 50kA, TPN MCCB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. Bus Copulars 1Nos. 1250A, 415V, Icu =50kA, TPN EDO ACB with ON/OFF/TRIP Indicating Lamps with MCB. 2Nos. 2000A, 415V, Icu = 50kA TPN EDO ACB with ON/OFF/TRIP Indicating Lamps with MCB. 1Nos. 400A, 415V, Icu = 50kA 4P Motor duity contactor with ON/OFF/TRIP Indicating Lamps with MCB. Make of ACB - Legrand -DMX3/ Schneider-NW/ABB -Emax Make of MCCB - Legrand -DPX3/ Schneider-NSX//ABB -Tmax All internal wiring of LT panel and capaciter panel connecting with LT panel as per requirement of load and ratings of the panel. (Complete panel described as above)

400 KVA CAPACITOR PANEL400 KVAR CAPACITOR PANEL (TTA Design as per IEC 61439-1/2) Make -(Legrand-XL3/ Schneider-Blokset/ ABB-MNS OEM) INCOMER : 1Nos. 1000A, 415V, Icu = 50kA, TPN MDO ACB with electronic trip unit for over current selective short circuit, instanteneous short circuit and earth fault protection and a set of CT's, ammeter with ammeter selector switch ON/OFF Indicating Lamps with MCB. 1 Set of phase indicating lamp with MCB BUS BARS 1250 A TPN bus bars of aluminium alloy. OUT GOING: 1 Nos. 100 KVAR, capacitor bank with 250A TP MCCB and Contactor, one set of indicating lights and Push Buttons. 4 nos. 50 KVAR capacitor bank with 160A TP MCCB and Contactor, one set of indicating Lights and Push Buttons. 4 nos. 25 KVAR capacitor bank with 100A TP MCCB and Contactor, one set of indicating Lights and Push Buttons. Additional space to be provided in each Capcitor bank copartment for fixing the filters in future. 1 no. 12 step Electronic type Auto matic power factor correction relay. Make of ACB - Legrand -DMX3/ Schneider-NW/ABB -Emax Make of MCCB - Legrand -DPX3/ Schneider-NSX//ABB -Tmax (Complete panel described as above)

SITC (Suplly , Instalation, Testing & commisioning ) of 1200mm 28 W Energy Efficeint sweep with electronic regulator ANCHOR , Atomberg ,Crompton greavesor equivalent . As per the selection done by Architect.

SITC (Suplly , Instalation, Testing & commisioning ) of Exhaust Fan, suitable for 1-phase, 230V with 2.5 mm square insulated copper conductor wires for connections complete as required. Make :ANCHOR , Panasonic,Crompton Greaves or equivalent . As per the selection done by Architect including bake lite sheet and all other accessories

Supplying, laying, testing and commissioning of 1100 volt grade XLPE insulated, PVC sheathed, aluminium conductor, armoured cable laid on existing cable trays / walls including the cost of saddling and clamping and including the cost of dressing to ensure minimum 1 cable diameter spacing between adjacent cables etc. complete as per specifications, as required and as below in existing cable trench.

3.5 core 300 sq mm XLPE aluminium conductor armoured cable

3.5 core 240 sq mm XLPE aluminium conductor armoured cable

3.5 core 150 sq mm XLPE aluminium conductor armoured cable

3.5 core 70 sq mm XLPE aluminium conductor armoured cable

3.5 core 50 sq mm XLPE aluminium conductor armoured cable

3.5 core 35 sq mm XLPE aluminium conductor armoured cable

Supply, installation ,testing and commissioning of Flood lights with high brightness white leds producing warm white light, non dimable protected with a tempered glass ,power consumption of 50 watt suitable for outdoor use IP 65 rated with all accessories and wiring, controlled gear as required.AFL 0206 Panasonic, philips or equivalent as per the selection of the architect

Supply, Installation & Testing of Prepayment Meters as per “IS 15884: 2010” by “BUREAU OF INDIAN STANDARDS” for AC Direct Connected Static Prepayment Meters. Three Phase Liberty Prepayment Meter 10A-63A with Dual register facility with Home display/ Freedom Unit. Meter should have inbuilt disconnect switches as per BIS requirement with Overload and Low balance alarm facility including all connection wire complete job.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.

Supply, Installation, testing & Commissioning PC for Local server having i7 processor with 3 GB RAM, 500 GB Hard Disk, Oracle Client, DVD Drive, USB Ports of Standard make. UPS of 500 VA with 15 min. back up, Laser jet Printer.

Vending software is certified by (ISO/IEC 27001) Supply, Installation, testing , Commissioning & Training of the vending System for Tariff designing as per BIS guidelines & Customer Data Base definition

Token Printer with Serial Port ( Epson make).Tokens are meter specified and encrypted with triple des technology. Also the vending system is ISO/IEC 27001 compliance with certification.

Supply, Installation & Testing of Prepayment Meters as per “IS 15884: 2010” by “BUREAU OF INDIAN STANDARDS” for AC Direct Connected Static Prepayment Meters. Single Phase Liberty Prepayment Meter 10A-63A with Dual register facility with Home display/ Freedom Unit. Meter should have inbuilt disconnect switches as per BIS requirement with Overload and Low balance alarm facility including connection wiring complete job.

Supply, Installation & Testing of prepayement meters as per "IS 15884:2010" by "BUREAU OF INDIAN STANDARDS" for Direct connected static pre payement Meters. Three phase liberty prepayement meter 10A-63A with dual register facility with home display/freedom unit. Mter should have inbuilt disconnect switches a per requirement with overloa and low balamce alarm facility.

Supply and laying of 2x2.5 sq mm FRLS PVC insulated Cum Armoured cable

HT PANEL ONE No. 11 KV HT Panel : Supplying, installation, testing & commissioning of H.V. air insulated distribution switchgear consisting of 1panel H.T. Board suitable for indoor installation for use on 11 KV 50 Hz earthed system having a symmetrical breaking capacity of 350 MVA at 11 KV comprising of 630A 33 KV vacuum circuit breaker. The panel shall be equipped with following accessories and specification compete as required. HT PANEL INCOMING / OUTGOING 1 No. each as following One No. 630 A Air insulated Metal clad housing A set of three 3 phase, 630A PVC insulated copper busbars. One Tripple pole draw out truck mounted 630 A, 1500 MVA, Isolator fitted with all necessary control devices. One Trip free, motor charged, spring released closing mechanism fitted with shunt trip suitable for 240 volt AC operation complete with necessary. Auxiliary switches, emergency hand trip device and mechanical ON and OFF indicators. 110/5A ratio, 15 VA, Class 1.0 Resin cast Current Transformers for metering purposes. Single phase horizontal draw out type resin cast line type potential Transformer of 33 kV/110 volts with 15 VA burden complete connected star / star with fuses as per requirements INSTRUMENT PANEL: * One 96 mm square, scaled 0-33kV flush type Voltmeter with 3 way and OFF selector switch. * One 96 mm square, scaled 0-100 amps, flush type ammeter with 3 way and OFF selector switch. * One static Triple pole very inverse definite mean time over current and earth fault relay with two outer elements connected for over current protection and the middle element for protection with adjustable over current and earth fault setting. * Trip circuit supervision relay, trip annunciation relay & trip circuit healthy relay. * One set of Lock out relay. * One set of Red / Green / Indicating lamps for close and open indication. * One set of Amber indicating lamp for Trip circuit healthy indication. * One set of white phase indicating lamps for phases.One number of dc Battery charger with batteries and stand as required. (Complete 1no. HT Panel as described above)

Supply, deliver, erection, testing and commissioning of 1250KVA, 11000 / 433 volts delta / star, outdoor oil type naturally cooled Transformer with vector group Dyn II, and on load tap changer of + 5% to - 15% on HT side in steps of 1.25% complete with first filling of oil with accessories as required of 433 volts on LT side the transformers to be provided with cable box on HT side to receive HT cable and LT side to receive LT cables complete as per IS 1180 specification and drawing as required. (Including M20 conrete base of required size comlplete job)

Supplying, laying, testing and commissioning of control cable 6 core 1.5 sq.mm. PVC insulated copper conductor 1.1 KV grade, armoured control cable in trench as required complete in all respect.

Supplying and fixing 1000 mm x 900 mm wide checkered rubber matting conforming to complete as required. 1100 V grade size 1000 x 900 x 15 mm thick

Supplying & fixing standard shock treatment charts in English & Hindi duly framed and covered with glass at different locations.

Supplying of fire bucket painted red and approved quality conforming to IS: 254/1974

Supplying and fixing carbon dioxide fire extinguisher type 4.5 kgs capacity of approved make with wall mounting bracket as required conforming to IS: 2878/1976

Providing & fixing HT danger Notice plate 200 mm x 150 mm made of mild steel at least 2mm thick & enameled white on both sides and with inscription in signal red colour with skull & bone on front side as required.

Providing 11 KV tested hand gloves.

Providing first aid safety box as per requirement.

Supplying , laying, testing & commissioning of following sizes of 11 KV grade Al. Conductor XLPE earthed cable in trench including digging & refilling of the trench etc. as required confirming to IS : 7098. 3 core 300 sq. mm

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of XLPE aluminium conductor cable of 11 KV grade as required.. 3 core 300 sq. mm

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs cable of 11 KV grade as required. 3 core 300 sq. mm

DG SET he DG sets and system offered shall comply to "Environmental Regulations on Engines for Generator Set Application and Generator Sets" issued by Central Pollution Control Board as amended up to date and other statutory regulation as applicable. Supply, installation, testing and commissioning of Following kVA,415 volts, 3 phase, 4 wire, 50 Hz at 0.8 power factor, ± 1% regulation, prime continuous rating Radiator cooled colded type diesel generating set with canopy along with base frame, brushless Alternator , class H alternator insulation, Static Excitation System, Lube Oil System, Electronic Governor Batteries,Instrumentation, oil fuel tanks, Silencer , Engine Control Panel, AVM pads, AVR Panel.Terminal arrangements shall be suitable for terminating cable with all other associated equipment as required. Obtaining clearance from Central Pollution Control Board (CPCB) & State Pollution Central Authority in respect of noise level and emission level being within permissible level and obtaining clearance from Electrical Inspectorate. (Including M20 conrete base of required size comlplete job)

250 KVA

750 KVA

Providing, fixing & installing exhaust pipe fabricated out of Class- C NS plate and all fixing accessories and hardwires. The exhaust pipes shall be insulated with 75 mm thick mineral wool insulation wrapped in chicken mesh and clad with 24 gauge aluminium sheet as required for installation at site complete in all respect with miscellaneous structural support for horizontal/vertical exhaust piping including fabrication, hardwares and painting as per specifications:.

300 mm dia

150 mm dia

silencers (250KVA).

silencers (750KVA).

Supplying, installation, testing and commisioning of passive infrared(PIR) technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load upto 10 amp,for mounting height upto 2.8 meter and for 5 meter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required. Make : Legrand , Philips , HPL . As per the selection done by architect (including wiring as required.)

(SUPPLY & INSTALLATION OF UPS) Supply,unloading,shifting installation, testing & commissiong of micro processor /DSP controlled 1 Numbers 6 KVA UPS IGBT based rectifier to achieve THDI 2% for linear load and 3% for non linear load.and input power factor of greater than 0.95 at 50% loading. True Online Double Conversion (VFI as per IEC 62040-3) UPS using PWM IGBT technology , 1 Phase input and 1 phase 220 V output UPS system; and each comprising of the following: 125% rated Rectifier cum charger unit +100% rated Invertor, Integrated in UPS module 100% rated External or inbuilt Galvanic isolation transformers of K-12 Delta/Zigzag type for isolation of input neutral with output neutral ,to be installed after UPS as shown in drawing enclosed. The External Galvanic isolationTransformer to be of same impedance for parallel operation. 100% rated Inbuilt static switch at the invertor output + 2 Nos. 100% rated Inbuilt static switches at the static bypass line. 100% rated Inbuilt Maintenance Bypass. 100% rated moulded case battery circuit breaker having Ithermal, Imagnetic and Automatic U/V trip mechanics. Web-enabled Monitoring and Management through SNMP protocols for multi-OS environments. UPS Efficiency to be mininum 93%, at full load Supplying, unloading,shifting , installing in position, testing and commissioning of Lead Acid sealed maintenance free batteries for 10 KVA UPS system , for providing 10 minutes backup to 10 KVA UPS for full load. The bank of batteries shall comprise required Nos complete as required. Supply,unloading,shifting , installation, testing & commissioning of matching cabinet/open racks including covering with netlon mesh to house SMF batteries for 10 KVA UPS system along with interconnecting links, MCCB etc. complete as required & as per specifications. Supply, laying, testing & commissioning of flexible single core copper cable for interconnections between UPS to UPS, UPS to batteries, Isolation transformer to UPS complete as required for 6 KVA UPS,including providing Battery circuit breakers as required.

Providing and fixing in position storage type hot water electrical gyser vertical or horizontal 2.5 kw 5 star including making connections in all respect.Hindware,Atlantic/RO Smithmake 25 litres capacity.

COMMERCIAL Panel (TTA Design as per IEC 61439-1/2) Make -(Legrand-XL3/ Schneider-Blokset/ ABB-MNS OEM) INCOMER : 1 Nos. 125A, 415V, Ics= 25 KA, 4P MCCB with overload, short circuit protection. 1 Nos. 0 - 500V voltmeter with selector switch, 0-250A ammeter with selector switch, and set of cast resin C.T.'s 125/5A 1 set of Phase indicating lamp with MCB BUS BARS: 200A TPN bus bars of aluminium alloy. OUT GOING: 7 Nos. 40A 415V, DP MCB of 10 KA withoverload, short circuit protection. 2 Nos. 32A 415V, DP MCB of 10 KA withoverload, short circuit protection. Make of MCCB - Legrand -DPX3/ Schneider-NSX//ABB -Tmax (Complete panel described as above)

Supply, Installation Testing of water prouf termenation cable joint kits with all asscories .

3.5 core 300 sq mm

3.5 core 240 sq mm

3.5 core 150 sq mm

3.5 core 95 sq mm

METER BOARD ASSISTANT PROFESSOR 12 FLATS METER BOARD ASSISTANT PROFESSOR 12 FLATS (TTA Design as per IEC 61439-1/2) Make -(Legrand-XL3/ Schneider-Blokset/ ABB-MNS OEM) INCOMER : 1 Nos. 400A, 415V, Ics= 50KA, 4P MCCB with overload, short circuit protection. 1 Nos. 0 - 500V voltmeter with selector switch, 0-400A ammeter with selector switch, and set of cast resin C.T.'s 400/5A 2 set of Phase indicating lamp with MCB BUS BARS: 500A TPN bus bars of aluminium alloy. OUT GOING: 13Nos. 63A 415V, TPN MCB of 10 KA withoverload, short circuit protection. provision for 3 phase Dual Energy meter with complete connection 2 Nos. 40A 415V, TPN MCB of 10 KA withoverload, short circuit protection. provision for 3 phase Dual Energy meter with complete connection Complete panel described as above