Small Scale Industries Development Corporation Limited Tender

Reinforced cement concrete work in wall (any thickness) including attached pilasters, buttresses plinth and string coarses, flits, columns, pillars. Piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering, shuttering, finishing and reinforcement (1:1:5:3 mix)

Form work of ordinary timber planks so as to give rough finish

Reinforcement for RCC work using TMT bars as required including cutting, hoisting and fixing in position complete

Structural steel work welded in sections incl. cutting, hoisting, fixing in position, and applying a priming coat of approved steel primer all complete(for control room) JINDAL OR SAIL make

P/F track deck crill make or equivalent H.I rib profiled sheets 1000 to 1020mm cover width 28-35mm high crests at 250 to 225mm TCT (total coated thickness) high tensile SMP Galvalume steel. The sheets have wide panes with 3 No. stiffing ribs, effective water shedding and special male/ female ends with fuil return legs on side Lapps for purlins support and anti capillary flute inside lapp. The sheets shall have a hot dip metallic coated of zinc and aluminum (150 gms/sm) zinc/aluminum coating mass total on both side AZ-150 as IS-1397,550PMA,yeild stress. Providing silicon modified polyester coating of approved colour of thickness of 35 micron comprising 20 micron exterior coat of SMP over 5 micron polyester back coat over 5 micron primer coats on both surfaces incld. side and end lap and using 8mm galvalume hex self drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end Lapps etc.(measured for unit of laid area).0.50mm thick

Structural steel work welded in sections for M.S tank incl. cutting, hoisting, fixing in position including priming coat of red oxide paint complete

Painting with synthetic enamel paint of approved brand and manufacture of required colour with two or more coats with ordinary paint of approved brand and manufacture

Providing & fixing Cores/Fine Bar screen with sport size 600x1000mm fabricated from SS304, 10mm dia bars with clear spacing of 15mm Quantity, MOC (SS304),Spacing (10 mm), Dimension (2x3 Feet),Type( Coarse cum fine),MOC( SS),Make(Approved Brand)

Supply, Installation, Testing & Commissioning of level indicators and controllers for automatic operation of the complete system with high/low level alarm complete with auxiliary No/NC contact. (Required in equalization tank, chlorine tank, sludge holding tank)

Supply, installation, testing & commissioning of submersible effluent transfer pumps Quantity2.0 (1W+S) ,Phase (Single),Power (2HP),Voltage (230 V),Frequency (50 Hz),Speed (2800 RPM),Head range (2.8-14 M),Suction size (50 mm),Delivery size (50 mm),Discharge(100-600 LPM),Material (Steel),MOC( CI),Type (Submersible),Make (Kirloskar/Crompton/ approved brand)

Supply, installation, testing & commissioning of Sludge Transfer Pumps Quantity2.0 (1W+1S),Phase (Single),Power (2 HP),Voltage (220-240 V),Frequency (50 Hz),Speed (2800 RPM),Head range (18 M),Suction size (40 mm),Delivery size (40 mm),Discharge (5.6 LPM),Material (Cast iron),MOC (CI),Type(Centrifugal monoblock),Make (Kirloskar/Crompton/ approved brand)

Supply, installation, testing & commissioning of Air blowers Quantity (2.0 (1W+1S),Operation (Continuous),Air flow(50m3),Inlet pressure (Atmospheric),Discharge (5000 MMWG),Blower speed (2000 RPM), Recommended motor (2.5-5 ,3-phase) (HP), Inlet temperature (Ambient),Outlet temperature (60 oC), Specific gravity (1),Inlet & outlet size (25NB),Noise level (80@1m distance),Capacity (50m3/h),Type (Ring type),MOC (CI),Make (Akash/ Everst/ Airvac)

Air piping shall comprise of pipes droppers/laterals with MS C class (epoxy coated) header complete with all fitting such as tees, crosses, plugs, sockets, elbow, reducer, supporters, & clamps, paddle flanges etc. cutting chases & making good.

Providing, installation & testing of Air diffusers for equalization tank, MBBR tank, chlorination tank Quantity, Type of aerator (Diffused aeration), Bubble diameter (1mm),Type of bubble (Fine),Size (63-90 mm),Shape (Tube), Material(EDPM/Silicon),Dimension(63-90 mm),Flow range (12-Mar m3),Diameter (63-90 mm),Design air flow (12-May m3),Clamps (SS),Bubble size (Fine),Air flow (12-May),Temperature (55 oC), Make (Approved Brand.)

Providing & fixing of all inter connecting piping with all required isolation control valves for making the system complete functional as per site. All piping submerged in effluent waste/pumping effluent waste shall be 10 kg/cm2 HDPE or schedule 80 CPVC pipes.

Supply, installation, testing & commissioning of MBBR media Density (94),Floating (Yes),Height(16 mm),Diameter (22 mm),Surface (410 m2/m3),Make (Approved Brand. Ltd)

Providing, installation & testing of tube pack media for settling tanks Type (PP-TSM),Area (12m2/m3),Angle (0.43M),Hopper Depth (1.6 M),Length (16.67 M),Structure (V type),Height (750x1000 mm),MOC (PVC),Thickness (1 mm),Color (Black),Settling Velocity (0.5 m/sec),SLR (1.7 m3/m2.hr),Make (Approved Brand)

Providing, fixing, testing & commissioning of dosing system Providing, installation & testing of dosing tanks for Alum, PAC & Lime Capacity (200 L),Type (Dosing),Bottom Diameter (575 mm),Height (910 mm),Top diameter (585 mm),Shape (Cylindrical)

Providing, installation & testing of agitators for fleshmixer & dosing tanks (Alum, Lime, PAC) Phase (Single),Power ( HP),Voltage (220-415V),Frequency (50 Hz),Speed (100-150 RPM),Capacity (Upto 7.5 HP),MOC (SS 304),Type (High speed),Make (Approved Brand)

Providing, installation & testing of dosing pumps Phase (Single),Power source (Electric), Voltage (230 AC V),Frequency (400 SPM),Power consumption (30 Watt), Dosing rate (1.5-15 LPH), Suction discharge (6 mm), MOC (PP),Type (Electronic metering), Make (E-Dose)

Supply, installation, testing & commissioning of factory assembled & tested vertical pump set with CI impeller, shaft of SS, CI suction & discharge & CI base & head, mechanical seal, connected to a TEFC induction motor. Providing, installation & testing of filter feed Pumps Quantity (1W+1S), (Phase (Single), Power(2 HP), Voltage (230V), Frequency (50 Hz),Speed (3000 RPM),Head range (12-Mar M),Suction size (80 mm), Delivery size (80 mm),Discharge (950 LPM),Material (Cast iron),Make (Kirloskar/Crompton/ CG),Type (Centrifugal mono block)

Providing, installation & testing of treated water Pumps Quantity (1W+1S),Phase (Single),Power (2 HP),Voltage (230 V),Frequency (50 Hz),Speed (3000 RPM),Head range (12-Mar M),Suction size (80 mm),Delivery size (80 mm),Discharge (950 LPM), Material (Cast iron),Make (Kirloskar/ Crompton/ CG),Type (Centrifugal mono block)

Supply, installation, testing & commissioning of MSEP vessel filter with frontal piping & associated valves & accessories. Providing, installation & testing of Multi grade sand filter (MGF) Flow rate (0.5 m3/h),Filtration rate (12 m3/m2/h),Standard model of filter (2354),Dia of filter (23 Inches),Height of filter(84 Inches),MOC (FPR),Type (Multiport),Size of MVP (20 mm),Filter media (Gravels/pebbles/sand),Frontal pipe & fitting (SCH 40 uPVC),Make (Approved Brand)

Providing, installation & testing of Activated carbon filter (ACF) Flowrate (0.5 m3/h),Filtration rate (12 m3/m2/h),Standard model of filter (2354),Dia of filter (23 Inche),Height of filter (84 Inches),MOC (FPR),Type (Multiport),Size of MVP (20 mm),Filter media (Gravels/pebbles/sand/ carbon),Frontal pipe & fitting (SCH 40 uPVC),Make (Approved Brand)

Providing, installation & testing of filter press Size (40x40 mm),No of chambers (40 No),Area (56.8 Sqm),Volume (1420 L),Grade (Semi-automatic),Filtration capacity (1000-20000 L/Hr),No of plates (20-40),Make (Approved Brand)

Supply, installation, testing, commissioning of metering devices Supply, installation, testing, commissioning of electromagnetic flow meters

Online pH meter to be installed at outlet

Panel mounted energy meter

Providing & fixing belt type electrical operated oil skimmer for Oil & grease removal Capacity (0-10 LPH),Dia of belt (75 Mm), Total length of belt (2000 mm endless Mm),Roller speed (30 RPM),MOC of tray(MS),MOC of roller (SS 304),MOC of belt (Elastomeric synthetic fiber),Make (Approved Brand)

Providing, installation & testing of servo/stabilizer Capacity (50 KVA),Make (Approved Brand)

Providing & installation fiber lining MOC (Glass fiber),Make (Approved Brand)

Commissioning No of days, Chemicals (Alum, lime, PAC, bacterial culture),Make (Approved Brand chemical),Team (Operators/CETP engineer)

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor control centre fabrication out of 14 gauge CRCA sheet steel. Cable gland plates shall be provided on top as well as the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of red oxide primer and final approved shade of powder coated paint 2 no’s earthing terminals shall be provided for 3 phase , 4 wire, 50 Hz supply system . lifting hooks shall also provided in case of large panels. Approval shall be taken for each panel before fabrication. Included of cables in accordance to specification with earthing form panel to each motor/ equipment.

Charges for consent to establish and operate from competent authority complete job.