Sher E Kashmir University Of Agricultural Sciences And Technology Tender

Supply /Installation and testing of 400 KVA 11/0.440 KV 3 phase copper wound distribution transformer , Make Alba/ABB with oil complete and confirming as per IEE rules and complete with test certificates including BI metallic clamps , lugs etc duly (Complete specifications are given at the end) BIS/IS approved/ Level 2 as per IS : 1180 ( Part -1) : 2014 to be installed at Bio Technology along with dismanltling of existing sub station at Bio Technology and shifting of same to Sensor Irrigation scheme near high mast .

S/I of Earth tester clamp On ground resistance tester Make Motwane/ Meco Digital type

Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.l strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.l. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G. I. nut bolt & spring washer spaced at 50mml

Supply and painting of each Pole 1 coat red oxide paint and 2 coats of aluminium paint (@ 1 ltr/pole red oxide paint and 1 ltr/pole aluminium paint)

Fabrication, supply, installation, testing & commissioning of outdoor type compartmentalized feeder pillar having front area not less than 0.60 Sqmtr (900 mm x 900 mm) and depth 45 Cm (NS) made out of 2mm thick CRCA sheet with tappered roof having separate cable and bus bar alley, 1 door arrangement i/c locking arrangement, having 400 Amp four pole aluminium bus bar of full length with base frame made out of 50mmx50mmx6mm (thick) angle iron having 80cm legs for erection in ground with construction of cement concrete suitable foundation size complete with connections and interconnections with copper conductor PVC insulated cables/ insulated aluminium busbar strips of appropriate size and terminal blocks (on outgoing) including supplying & fixing following switchgears & accessories there in, powder coating, labelling, earthing etc. complete as required. Providing and fixing following accessories in existing cubical panel board i/c making connection etc. as reqd. For 400 KVA Sub station with 1000 A Bus Bar Al 4 Strip. Details as under MCCB-630A Incomer-50KA = 1No. Panel Powder Coated 2.0mm MCCB 400 A 4P 50kA , Thermal release 50KA x 1 No. handle extender type MCCB 315 A 4P 50kA , Thermal release 50KA x 1 No. handle extender type Digital V,A,F, PF Meter Class 1.0 L&T 2 No.CT 600/5 AE 2 Set Spreader Terminals For DU MCCB 1 Set , , Panel Accessories like nut bolts, locks, etc

Supplying and erection of 11 KV pin insulator complete with large steel head G. I. pin, nuts, washers etc. as required

33 kV link set Heavy duty complete with all accessories ISI standard Heavy duty 600 Amp

Muky claps /J hook , galvanized nuts and bolts as required for all items included . Complete job for entire work

S/l of Guy with turn buckler and Guy insulator etc, 8 SWg twisted GI wire laid in cement concrete . Complete job in all respects.

Excavation for foundation in soft soil including dressing of sides and cum ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as direted, within a lead of 50 metres. (12x9x1.5ft)

Providing and laying in position cement concrete 1 :2:4 (1 cement : 2 cum coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required. (9x9x9ft)

Centering and shuttering including strutting , propping etc and removal of foam for foundation footing bases of column etc for mass concrete. 2(18+18 ft) x7 ft)

Excavating earth rubbish by mechanical transport upto a lead of 5 km and disposal of rubbish

12mm cement plaster of mix 1:6 sides of concrete foundation for transformer 139.5 sft

Fabrication of shelter with GI roofing and GI glvanized chain link fencing , support structure and entry door etc . Complete job in all respects . Size of platform 10x8x10 ft height with foundation work etc as needed above ground 24 Inches.

Fabrication, supply, installation, testing & commissioning of outdoor type compartmentalized feeder pillar as required and depth 45 Cm (NS) made out of 2mm thick CRCA sheet with tappered roof having separate cable and bus bar alley, 1 door arrangement i/c locking arrangement, having 300 Amp four pole aluminium bus bar of full length with base frame made out of 50mmx50mmx6mm (thick) angle iron having 80cm legs for erection in ground with construction of cement concrete suitable foundation size complete with connections and interconnections with copper conductor PVC insulated cables/ insulated aluminium busbar strips of appropriate size and terminal blocks (on outgoing) including supplying & fixing following switchgears & accessories there in, powder coating, labelling, earthing etc. complete as required. Providing and fixing following accessories in existing cubical panel board i/c making connection etc. as reqd

INCOMER 400 Amps FP Icu=Ics=100% with Breaking Capacity 50 KA (01 Nos) Shunt trip coil and Single Phase preventer. Indicating Lamps RYB (1 Set) Voltmeter-0-500 Volts(1 Nos) Ammeter(0-150 A)(1 Nos) Selector Switch (2 Nos) Current Transformer 100/5 A 10 VA Burden, Class-1(1 sets) Aluminium Busbar 600 Amps FP E-91 E Grade Electrolytic Aluminium Gland Plates to be 3.0 mm Thick. Outgoing Thermal Magnetic Based MCCB 250 Amps FP x 1 No Thermal Magnetic Based MCCB 160 Amps FP x 1 No Icu=Ics=100% with Breaking Capacity 50 KA By pass changeover 200 A = 1 No 4 P and 100 A FP =1 No ON load L&T /Equivalent Make

SITC of Servo stabilizer of following specification: capacity: 1. Capacity : 200 KVA 2. Input voltage: 208- 460 V PP 120V -220V NP 3. Output: 415 Volts +/- 1 % 4. Winding Material : 99.9 % Pure copper wound strip with fibre glass 5. Un- balanced type 6. Dimmers with heat Sink based technology 7. Cooling : Oil Fresh IS 335 8. Micro Controller LCD True RMS with RS 485 Interface 9. Protection are overload, High Voltage, Under Voltage, Delay line, Single Phase , Preventive Neutral failure, through micro controller & L&T Make Connector 10. Display Parameters are KW, Current Power factor, Input, Output, Frequency, Trouble Shooting 11. Auto Manual Selector switch with up/down switch in case card gets fault. 12. Heavy duty Al, bus bar wiring input and output. 13. Servo stabilizer tank shall be design in MS sheet Heavy gauge as suitable. 14. cooling of oil / Oil Level inlet, lifting huks etc 15. Earth terminal 16. Efficiency more than 98 % 17. Design as per IS 2026 18. Multi function meters L&T Make 19. Warranty 1 year.

S/L of Cable 3.5 core 240 Sq mm Al armoured with termination works etc

S/L of Cable 3.5 core 185 Sq mm Al armoured with termination works etc

S/L of Cable 3.5 core 95 Sq mm Al armoured with terminatio works etc.

S/L of Cable 3.5 core 70 Sq mm Al armoured with terminatio works etc.

Supply and laying of folowing size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground 75mm below level including excavation and refilling the trench but excluding sand cushioning and protective covering etc , complete as required.

90 mm dia nominal)

120 mm dia nominal)

Fabrication, supply, installation, testing & commissioning of outdoor type compartmentalized feeder pillar having front area not less than 0.60 Sqmtr (900 mm x 750 mm) and depth 45 Cm (NS) made out of 2mm thick CRCA sheet with tappered roof having separate cable and bus bar alley, 1 door arrangement i/c locking arrangement, having 400 Amp four pole aluminium bus bar of full length with base frame made out of 50mmx50mmx6mm (thick) angle iron having 80cm legs for erection in ground with construction of cement concrete suitable foundation size complete with connections and interconnections with copper conductor PVC insulated cables/ insulated aluminium busbar strips of appropriate size and terminal blocks (on outgoing) including supplying & fixing following switchgears & accessories there in, powder coating, labelling, earthing etc. complete as required. Providing and fixing following accessories in existing cubical panel board i/c making connection etc. as reqd. For 250 KVA Sub station with 1000 A Bus Bar Al 4 Strip. Details as under Panel Powder Coated 2.0mm MCCB 160 A 4P 36kA , 1 No. handle extender type Digital V,A,F, PF Meter Class 1.0 L&T 2 No.CT 600/5 AE 2 Set Spreader Terminals For DU MCCB 1 Set , , Panel Accessories like nut bolts, locks, etc

Note:-The rates quoted are inclusive of all carriages of materials (Mechanical/Manual) from source to site work and all extra charges including dewatering if any during the execution of work till complete in all respects.