Sher E Kashmir University Of Agricultural Sciences And Technology Tender

CAST-IN-STU DESIGN MIX M25: Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix,incluyding pumping of concrete to site laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportiond as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable seperately all works Below Plinth Levl / Above Plinth Level upto level V (AGL/BGL).. (code 5.34)

ABOVE GROUND FLOOR SLAB LEVEL

FORM WORK: Centering and shuttering including strutting, propping etc. and removal of formwork from the site, for all works from foundations, to roof level. (code 5.9)

ABOVE GROUND FLOOR SLAB LEVEL

STEEL REINFORCEMENT: Steel reinforcement for R.C.C. works including straightening, cutting, bending, placing in position and binding - all complete from foundation to roof level of Thermo-Mechanically Treated bars of grade Fe-500D or higher. (code 5.22.6)

STRUCTURAL STEEL:Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. plates, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer also included. (code no 10.2.2 )

ANCHOR BOLTS: Providing and fixing bolts including nuts, washers complete job.

Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 insuperstructure above plinth level upto floor V level in all shapes and sizes in :(Cement mortar 1 :6(1 cement : 6 coarse sand) Extra for brick work with common burnt clay bricks/cement concretebricks in superstructure above plinth level upto floor five level

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand) Extrafor half Brick masonry in superstructure above plinth level upto floor V level.Extra for providingand placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry incldall carraiage upto site .

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 fine sand)

12 mm thick cement plaster in (1 cement: 4 fine sand mix). Upto floor V level complete in all respects (including cost of all material, leads, lifts and carriages etc. upto site of work complete).

Providing and fixing of U-PVC sliding/casement/fix window in white colour,frame 60mm thick (min) x 90mm (min) with 1.5 mm GI reinforcement sash 39mm (min) 58mm (min) with 1.25mm GI U section reinforcement with rubber gasket of grey / black colour 10 years warranty against weathering of profile with complete hardware fittings and with 5mm thick toughened glass and fiber jalli option pre- febricated on german fabrication system( mosquito sash 18mm(min) x 43mm(min)(with welled cornes) complete at site (for glazing/wire guage shutters) finesta make

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood

Providing and fixing 35 mm thick panelled or panelled and glazed shutters for doors including 30mm thnick ornimantal panalled including butt hinges and necessay secrews all complete as per the direction of engineer in charge

providing and applying PU polishing, Two or more coats on new works including a coat of wood filler

Painting with synthetic enamel paint of approved brand and manufacture including applying priming coat with ready mix pink of approved brand and manufacture on wood work etc. including cost and carriage of all materials equipments complete job as per drawings, specifications and as directed by the engineer Incharge.

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and applying cement based wall putty of required thickness over plastered surface to prepare the surface even and smooth complete in specified areas as per specified patter. (Birla make) (including cost of all material, leads, lifts and carriages etc upto site of work complete).

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete (WITH SKIRTING 6")

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.(Crushed)

Providing and fixing plannes eaves boarding (300mm x 40mm )( nominal size) second class dewdare wood fixed with screws etc, including all carraiges .All job completed

Providing and fixing 20mm thick wooden planks ceiling/ soffit(frame work for base to be paid for separately) with M.S. screws Second class kail wood

Providing colour coated sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.5 mm thick

Providing and fixing thermal insulation of ceiling (under deck insulation) with specified glass wool conforming to IS: 8183, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3mm) @ 60cm c/c and wire mesh of 12.5mm x 24g wire for top most ceiling of building. With resin bonded rock wool with density 48 kg/cum

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gram/m

Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position

Providing & applying Plaster of Paris (gypsum anhydrous) suspended false ceiling Cove false ceiling), up to any height above floor level, including fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive). Consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts. Other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size.The other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre. This shall be fixed in adirection perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval and reinforced with rabbit wire mesh of 100mmx16mm gauge fixed to frame.

Pointing on brick masonry in lime Surkhi (I Lime: 2 Surkhi ) including finishing the joints with lime surkhi pigments to give a local heritage touch as per the directions of Engineer incharge upto desired height complete in all respects. (Including all lead, lift, labour, materials, tools, plants complete as per specification and as directed by Engineer in Charge.

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge:In cement mortar

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : Of area beyond 3 sqm.

Providing and applying ornamental moulding in cementing plaster vertical post with mix of 1 cement and 1 fine sand(1 :1 mix ) including material scuffolding shuttering etc complete job as per architectural drawing/ and approved by consultant / client

Providing and fixing (ornamental type) members for exterior face of (ARCHITRAVE) as per the directions of consultant including cost of all material ,leads lifts and carriages upto site of work complete).

Providing and fixing Wooden Flooring Herring bone AC -5 Grade 8mm-12mm Thick including all accecories , beadings , kanas , screws , profiles etc complete (Size and Design of the pannel Fitting to be selected by Engineer Incharge) :

Providing and fixing of brass fittings of approved make

sliding door bolt 300x16mm long

Tower bolt 200 x10 mm

Handle 150mm

Note:-The rates quoted are inclusive of all carriages of materials (Mechanical/Manual) from source to site work and all extra charges including dewatering if any during the execution of work complete in all respects.