Public Works Department Tender

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

Providing and fixing M.S tubular frames for doors, windows, ventilators and cupboard with rectangular /L-type sections, made of 1.60 mm thick M.S Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10cm of C.C. 1:3:6 (1cement : 3 coarse sand :6 graded stone aggregate 20mm nominal size)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).30 mm.Second kail wood.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Second Class kail wood.

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge 30mm.Second class Kail wood.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 30mm Second class Kail wood

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.In all colours, shades, except White, Ivory, Fume Red Brown.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level.1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns.

Centering and shuttering including strutting, propping etc. and removal of form for:Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Edges of slabs and breaks in floors and walls Under 20 cm wide.

15mm Cement plaster on the rough side of single or half brick wall of 1 : 6 ( 1 cement : 6 fine sand).

providing and fixing of laminated wooden panelling 8mm thick AC-4 under layer frame of 12mm thick complete job.as techinical specified.

providing and fixing of laminated wooden flooring 8mm thick AC-4laminated using 2mm thick foam complete job as technical specified.

Providing and fixing PVC rigid foam sheet 1mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps.

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm.

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms.

Providing and fixing toilet paper holder C.P. brass.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour:450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

providing and fixing SS grating with frame including fixing to the floor with cement mortar.

providing and fixing health faucet 15mm dia with CP flush pipe, CP nozzel hook complete including CP flange etc.

providing and fixing PVC pipe class -3,6kg /cm2 with cement solvent joint,complete with all fittings and clamps etc includin g cutting and making good the walls and floors for waste pipe from wash basin,urinals,sinks & baloony drainage, as directed by the Engineer -in charge . including cement concrete 1:2:4 mix ( 1 cement :2 coarse in sand :4 graded stone aggrigate ,20mm down gauge ) 75mm in bed and all around soil and waste pipes under floor, including shuttering and centering for:-.

32mm nominal bore

40mm nominal bore

110mm out dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.

15mm nominal outer dia pipes.

20mm nominal outer dia pipes

32mm nominal outer dia pipes.

Providing and fixing uplasticized PVC connection pipe with brass unions 15 mm nominal bore.

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm).

Finishing walls with Acrylic smooth exterior paint of required shade:Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface).

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer.

Distempering with 1st quality Acrylic/oil bound washable distemper (ready-made) having VOC content less than 50 grams/litre of approved manufacturer and of required shade and colour complete as per manufacturers’ specifications, one or more coats on old work.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 1 mm thick.

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete 300x16 mm.

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete

250x10 mm

150x10 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating bnot less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

125 mm

75 mm

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.

Supplying & Placing Modular table in completely knock down conditions with an overall size 2200mm X 1950mm X 750mm that is to be assembled at site. The top shall have the size 2000mm X 1000mm made up of 36mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape with Aluminium L-section and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the ssistance of edge banding machine at 200 degree Celsius. The table top shall be supported on particle board based gable end at one side and 75mm Peg on another side. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 49mm thick Pre-laminated particle board and profile shall be in linear shape and covered by Aluminium profile and edges with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick pre-laminated particle board in linear shape with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The side top shall be provided with an overall size 1950mm X 600mm. Single sided power connection box shall be enclosed at table top that houses telephone cable, data and power connection discretely. The side top shall be supported on metal peg which mounted over side storage unit. The edges shall be covered by Aluminium profile. The table shall have side unit for storage purpose with an overall size 800mm X 500mm X 65mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 drawer with same size. The drawer shall be operated with SS handle and easily close & open with the assistance of ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The side unit shall be mounted on 50mm Peg. The anufacturer shall have quality and safety assurance like ISO-9001:2015, ISO- 14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Providing and supplying a medium back chair with ergonomic design, comfortable & sthetically appealing. The seat and back shall be made of 18mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite apestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the pine which helps to provide lumbar support. The chair shall be supplied with PP arm with cushion aving leatherite covering top pivot joint with back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustmen. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per NSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged Polypropylene base with chrome having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA andards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(D) X 550±10 mm(W) and back size shall be 550±10 mm(W) X 560±10 mm(H) from seat. Overall height shall be = 1020±10 mm, overall depth = 690±10 mm & overall width = 700±10 mm.

Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and having density 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam thick having density 32Kg/m³. SS strip shall be provided on front of the arm having length 515mm with cross-section area 14mm X 4mm. The structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have shiny chrome finish SS leg with height 100mm and 10mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 500±10 mm(D) X 1015±10 mm(W), seat height = 430±10 mm, overall width = 1160±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm.The participating brand must have all the prevalent quality & safety related certifications like ISO:9001, ISO:50001, ISO:14001, OHSAS:18001, BIFMA, AIOTA for one or more product, Green Guard certificate for any one product atlest issued by UL of USA. The approved brands are Godrej, Geeken, Haworth, Steelcase & Merry fair only.

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and having density 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam thick having density 32Kg/m³. SS strip shall be provided on front of the arm having length 515mm with cross-section area 14mm X 4mm. The structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have shiny chrome finish SS leg with height 100mm and 10mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 500±10 mm(D) X 1015±10 mm(W), seat height = 430±10 mm, overall width = 1160±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm.The participating brand must have all the prevalent quality & safety related certifications like ISO:9001, ISO:50001, ISO:14001, OHSAS:18001, BIFMA, AIOTA for one or more product, Green Guard certificate for any one product atlest issued by UL of USA. The approved brands are Godrej, Geeken, Haworth, Steelcase & Merry fair only.

Providing and supplying mid back chair. The seat shall be made of 15mm thick hot pressed mercial plywood upholstered with high resilience polyurethane foam (40+16)mm thick having density 40kg/m³ with foam net tapestry 0.9mm thick and 300 GSM and the back shall be made of 19mm dia. MS chrome pipe upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with contoured lumbar support having cushion pad. The seat and back shall be arrested together with powder coated HR steel spine and the armrest shall be used adjustable PU arm completely joint with seat. For seating durability the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per NSI/BIFMA X5.1-2011 standard. The pedestal should have five legged MS/CRCA chrome plated having pitch circle Dia. 700 mm fitted with 5 nos. twin wheel castors. The castor of the chair should be jction moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The Seat size shall be 490±10 mm(W)X470±10 mm(D) and back size shall be 600±10 mm(H) from seat & overall height = 1040±10 mm.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size).

Engagment of labour skilled/ un skilled for election, rectification,cutting etc of damaged fecing ar as directed by EIC and disposal unserviceable meterial upto 50mtr lead.

Labour

welder

Hire charges of weldiong set incl.welding rod complete

Carriage of Meterial by Mechanical Transport including loading and unloading and stacking complete job at site.

Carriage of bricks at an average lead of 180. kms by MT

Carriage of Sand at an average lead of 10. kms by MT

Carriage of Bajree at an average lead of 05.00kms by MT