Public Works Department Tender

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 ( 1 cement : 6 fine sand) [including all leads, lifts, and carriage complete]

Extra for brick work in superstructure above plinth level upto floor V level. (By manual means) [including all leads, lifts, and carriage complete]

12mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 coarse sand) [including all leads, lifts, and carriage complete]

6mm cement plaster to ceiling of mix 1 : 3 (1 cement: 3 fine sand) [including all leads, lifts, and carriage complete]

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 coarse sand) [including all leads, lifts, and carriage complete]

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Sal wood [including all leads, lifts, and carriage complete]

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including lSI marked M.S. pressed Butt hinges bright finished of required size with necessary screws excluding panelling which will be paid for separately,al! complete as per direction of engineer- in charge. Second class deodar wood

Providing and fixing fly proof galvanised M.S. wire gauze to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm all complete. With 2nd class teak wood beading 62x19 mm

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Sal Wood

Providing and fixing 30 mm thick wire gauze shutters using galvanised M.S. wire gauze .of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows: Second class deodar wood

Demolishing cement concrete mechanical means including disposal of material within 50 metres lead: 1:3:6 or richer mix [including all leads, lifts, and carriage complete]

Cement concrete flooring 1:2:4 ( 1 cement: 2 coarse sand . : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 50 mmthick with 20mm nominal size stone aggregate. [including all leads, lifts, and carriage complete] (a) Crushed.

Proofing asbestos cement 6mm thick corrugated sheets roofing and fixing with G. I J, or L hooks, bolts and nuts 8mm dia, G.l plain and bitumen washers complete excluding the cost of purlins, rafters and trusses : corrugated sheets. Upto 60 degrees pitch [including all leads, lifts, and carriage complete]

Half brick masonry with bricks of class designation 75 in foundations and plinth in : Cement mortar 1 :4 ( 1 cement : 4 coarse sand) [including all leads, lifts, and carriage complete]

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including priming coat with cement primer

Wall Painting with plastic emulsion paint of approved lj brand and manufacture to give an even shade. Two or more coats on new work

Applying priming coat: with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat: with ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 course sand 4 graded stone aggregate 20mm nominal size. Crushed

Providing and laying integral cement based water proofing treatment including prepration of surfaces as required for treatment of roofs, balconies, terracies etc consisting of following operations. [including all leads, lifts, and carriage complete] a) applying a slurry coat of neat cement using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement: 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300mm heightincluding rounding of Junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. d) finishing the surface with 20mm thick jointless cement mortar of mix 1 :4(1cement: 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved byEngineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finially finishing the surface with trowel with neat cement slurrv and making pattern of 300x300mm/sq 3mm deep. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurra as 65 mm.