Public Works Department Tender

2 X 1.5 sq. mm +1 X1.5 sq. mm earth wire

2 X 2.5 sq. mm +1 X 2.5 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing of 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. ( Anti bacteria series of ABB /L&T/Havels /Legrand make , )

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing of 2 No's of 3 pin 5/6 A modular socket outlet and 2 No's of 5/6 A modular switch, connections etc. as required. ( Anti bacteria series of ABB /L&T /Legrand /Havels make)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.( Anti bacteria series of ABB /L&T /Legrand /Havels make)

Supply and laying of 25 mm dia medium class PVC medium grade Conduit to berecessed on walls / floor complete with all allied accrues like bends, tees etc. for paving way of laying of wires of haeting points /circuits ,machine points /circuits and sub mains .The Job includes cutting of walls / floors with required hydraulic cutter and refacing of walls with cement plaster of required ratio or with P.O.P after laying of conduits refacing to its original position by way of supply and applying of painting of required colour to effected area's.Anchor/Polycab/Finolex/TMT Plus make.

Supply, Installation, Testing and Commissioning of 1200 mm sweep ceiling fan, 3 nos. blades, 30 cm long down rod, suitable for 230 V, 50 Hz, single phase AC Supply etc. complete as required of Crompton /Havels / Usha /make (3 Star )

Supply, Installation testing and commissioning of 200-250 mm sweep Exhaust Fans of Usha / Crompton Greaves / Havel's /Orient incl making of necessary connections and making of necessary space in walls / Windows as per site.The Job includes providing and fixing of shutter of suitable size hylum sheet for fixing of exhaust fan

Supply, Installation, testing & commissioning of IP20 Recessed LED Downlighter made of pressure die cast aluminum housing. Fixture should have minimum efficacy at System level (Not Chip Level) ≥110 lumens/watt with Minimum system Lumens 1000 with maximum system wattage of 9W. The downlighter shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 6500°K, SDCM≤5 & CRI≥80. The luminaire driver shall comply to following parameters at 220V to 240V: PF≥0.95 (@full load), THD ≤ 10% (@full load) & in-built surge protection of 3KV (DM mode). The input voltage range shall be 120V to 320V. The fixture should comply with the parameters as per IS10322. The luminaire shall have class B serviceability. The luminaire height shall be minimum 40MM, with minimum cut-out dia of 125mm & the lip shall be minimum 8mm. The luminaire shall be IK02 compliant. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL of Philips /Lighting Techonology / Wipro / Trilux make

Supply and fixing of 12-15 Watts LED surface /recess (Commercial type) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. The downlighter shall be back-lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing should made of pressure die-cast aluminium. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver. Approved make Philips / Lighting techology / Trilux /wipro (to be approved before installation)

Supply ,installation ,Testing and Commissioning of 10-12 Watts ,2 ft long LED tube light fitting having PVC Body (Commercial type) of standard make dully isi marked ,incl ceiling rose and 2-core transparent wire for connections complete job.The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit initial system lumen output of 1400 lumens with minimum system efficacy of 120 lumen/watt. The luminaire shall comply to lifetime of 50000Hrs @ L70B50 with design ambient temp 45°C. The electronic driver used shall have a power factor ≥0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, THD≤10%, Current Ripple ≤5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I. The luminaire should be of Class B serviceability. The luminaire should be at least IP20 & IK02 rated. The minimum dimensions of the batten shall be 44mm X 51mm X 1157mm. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. Approved make Philips / Lighting techology / Trilux /wipro (to be approved before installation)

Supply ,Installation ,Testing and Commissioning of IP66 , 100 Watt LED Flood light Luminaries (Warm light) having Aluminium body of of standard make dully isi marked complete job.The system efficacy of the luminaire shall be ≥120lm/w. The LEDs used in the luminaire shall be from either Lumileds, Osram, Nichia, APT Electronics and CREE make, shall have CCT of 2700-3200°K, CR≥70, SDCM≤5, Life of 50000Hrs @ L70B50. The luminaire shall have IP rating of IP66 & IK rating of IK07. The luminaire shall have lens made of polycarbonate & optical cover made of toughened glass. The LED driver shall have operating voltage range of 140V to 270V, PF≥0.95 @ full load, THD≤ 10% @ full load, In-built surge protection of 4KV, HV Cut off @ 325V (±15V). The luminaire shall have 10KV SPD in-built inside the luminaire. The maximum dimensions of the luminaire shall be, L: 264M, Depth: 52MM & height without cradle: 203MM. The nominal weight of the luminaire shall be maximum 2.4KGs. The luminaire driver & it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material for approval. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. Approved make Philips / Lighting techology / Trilux /Wipro (to be fitted on attic of building) The job includes providing and laying of foundation Block (H x w x L) 2 ft x 1 ft x 1 ft in 1:2:4 ratio Including cost of execuation and Civil materials with its carriage from source to site of work with allied 2 No's of Foundation nuts & bolts of required size and length for holding of Flood Lighting luminaries on Ground for focusing towards building

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator) of Legrend /L&T /ABB /Simens make

`16 way, Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioninq etc. as required of legrand / ABB /L&T /Simens make

Supplying and fixing of 40 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Simens /Schinder make dully isi marked complete with connections.of Legrand / ABB /L&T /Simens make

Supplying and fixing of 63 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Simens make dully isi marked complete with connections

Supply,Laying,Testing & Commissioning of 35 sq.mm 2- core armored Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/paramount /KEI make, including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections. The cable is to be laid partially under ground including execuation and refilling back after cable laying and partially above ground including clipps etc.

Supply,Laying,Testing & Commissioning of 10 sq.mm 2- core armored Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/paramount /kei make, including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections. The cable is to be laid partially under ground including execuation and refilling back after cable laying and partially above ground including clipps etc. for normal and invertor supplies from panel to Guards rooms

Supply and laying of DWC double layer Corrigated pipe having 38 mm dia to be laid under ground upto 50 Cm's in deep including execuation and refilling back and disposal of surplus earth complete job.

Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoall coke and salt as required.The job includes providing and fixing of main hole PVC Chamber with its cover complete job

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supply ,Installation ,testing and commissioning of LED Strip lights with connector IP65 water proofing strip light with 400 Lumens / meter (Warm white ) of Philips Make

SITC of 50 Ltrs Geyser 230volt,50 Hz, 2000 watt with thrmostater and auto cut facilitieson the wall with providing the connection pipe and making proper connection with the existing water pipe etc as required Monza DX.Make-Havells/Racold /Jaquar /Hindware make) .

Supply,Installation,Testing & Commissioning of 2000 VA Power Inverter (24 Volts) Sine wave type of make (Sukam / Luminous / Exide / Micro tec/Liv guard make ).The invertor shall have inbuilt display unit showing input and output voltage ,Charging voltage , output current etc with having inbuilt protection device of suitable capacity . The invertor should invertor and UPS mode of operation . The job further includes Supply , Installation , Testing & Commissioning of 2 No's of 180 AH /12 V Tall tubular Inverter Batteries of same make as of inverter ,the batteries are to be housed in PVC Trolley , incl cost of pvc trolley. complete job.The job includes AMC of batteries and invertor for a period of three years ,which includes quarterly servicing of devices & as and when required. complete job.

Supply/ installation/testing and commissioning of Wall / floor mounted compartmentalized , 415 volts TPN MCCB Main Distribution panels ,fabricated out of sheet steel of 16 gauge dust protected, duly painted with powder coating ( not less than 80 microns ) incl earth terminal with all necessary accessories as required for panel (IP 54) with internal wiring of panel .The Panel is to provided and fitted with following adjustable type controlling /Protection switch gear devices (1) Normal Incoming (1A) 125 Amp DP MCB (10KA) of Legrend / L&T /Simens / ABB make = 1 no (1B) 200 Amp PN Aluminium Bus bar = 1 Set ( Bus Bar shall be insulated with heat shrinkable sleeves and shall be colour coded. having minimum size 20 mm x 10 mm with spacing as per latest IE Standards) (1C) One No. (1 No.) digital multifunctional meter for measurement of voltage ,current and power etc with Selector switch ,push battons and one set of CT's of ratio 250 A/5A ,CL 1.0 ,15VA . (3) Invertor Incommer 100 Amps DP MCB (10KA) of Legrend /L&T /Simens / ABB make =1 No. 63 Amps F.Pole panel mounted Change over Switch of havels /Standard /HPL make = 1 No. 100 Amp PN Bus bar Al Strips = 1 Set ( Bus Bar shall be insulated with heat shrinkable sleeves and shall be colour coded. having minimum size 10 mm x 10 mm with spacing as per latest IE Standards) (1C) One No. (1 No.) digital multifunctional meter for measurement of voltage ,current and power etc with Selector switch ,push battons and one set of CT's of ratio 63 A/5A ,CL 1.0 ,15VA . (1D) 1 Set of phase indication lamps (4) Outgoing . 63 Amps Double Pole MCB (10 KA) of Legrend / L&T /Simens / ABB make = 3 No 40 Amps Double Pole MCB (10 KA)of Legrend /L&T /Simens / ABB make = 4 No The Panel manufacturing unit should be CPRI Registered with latest ammended IEC / IS 61439 and the Contractor has to submit the test certificate of main switch gear's and Drawing's of panel (Showing claerly dimensions of panel with spacing of switchgear as per IE Standards ) & is to approved by Department not less than the rank of SDO before manufacturing of panel.