Public Works Department Tender

Supply installation testing & commissioning of Professional four channel Power amplifier, 4x 750 - 800W @ 8 ohms, 4 x 1250 - 1400W @ 4 ohms, Sensitivity - 1.6Vrms (+6.3dBu), Input Impedence - 20kΩ, Crosstalk: ≥65dB - 70dB, S/ N ratio - 101dB, Damping Factor: 600 - 800, THD: 0.01% , Slew Rate - 30V / us, etc complete as required.

Supply installation testing & commissioning of Class H or Class D Dual Channel Professional Power amplifier for surround speakers , with 2 x 600W 4 ohms power & 2x 400W 8 ohms , Minimum Damping factor 500, Frequency Response (-1dB) 20~20000Hz, Typical THD (half power, 1kHz, 8 ohms) 0.1%, etc complete as reqd.

Supply installation testing & commissioning of 2 In x 6 Out Digital management System, Analog Input 2 x XLR electronically balanced, Analog Output 6 x XLR electronically balanced, AD & DA Converters 24bit 96kHz, Minimun Load 150 ohm, THD+N 0.005% at 1kHz 0dBu, 0.01% at 1kHz 16dBu, S/N 106 dBA, Frequency Response 20Hz – 20kHz; ±0.5dB, etc complete as required.

Supply Installation testing & commissioning of 16 channel input analog mixing console with Max. 16 Mic / 20 Line Inputs (12 mono + 4 stereo) / 4 GROUP Buses + 1 Stereo Bus / 4 AUX (incl. FX), 24-bit/192kHz 2in/2out USB Audio functions, +48V phantom power, XLR balanced outputs etc as required.

Supply installation testing & commissioning of Wireless Handheld Microphone System, Carrier frequency range 500 – 865 MHz, Modulation FM (Frequency Modulation), T.H.D. at 1 kHz typ. 0.8%, Signal/noise ratio typ. 105 dB(A), etc as required.

Supply installation testing & commissioning of Wireless Lapel Microphone System, Carrier frequency range 500 – 865 MHz, Modulation FM (Frequency Modulation), T.H.D. at 1 kHz typ. 0.8%, Signal/noise ratio typ. 105 dB(A), etc as required.

Supply Installation testing & Commissioning of 16" Gooseneck cardioid Microphone, polar pattern cardioid, Frequency Range 80-18,000Hz, Sensitivity16mV/Pa, Nominal impedance 220 Ω ± 30%, DC 48 V phantom power, Max. sound pressure 125 dB, Complete etc. as reqd.

Supply Installation testing & Commissioning of Dynamic Vocal Microphone, polar pattern Super cardioid, Frequency Range 50-15000 Hz, –54.5 dBV/Pa (1.85 mV) 1 Pa = 94 dB SPL, Impedance 600 ohms etc.complete as reqd.

Supply Installation testing & Commissioning of Dynamic Instrumental Microphone, polar pattern Super cardioid, Frequency Range 45-15000 Hz, –54.5 dBV/Pa (1.85 mV) 1 Pa = 94 dB SPL, Impedance 600 ohms etc as reqd.

Supply Installation testing & Commissioning of Floor Mic Stand, etc complete as required.

Supply Installation testing & Commissioning of Table top Mic Stand, etc complete as required.

Supply Installation testing & Commissioning of main SYSTEM RACK ( 24U ) - M.S. Rack with Power indicator, power sockets and isolator fitted duly prewired to accommodate Control Room equipments e.g. Amplifiers, Controller, Equalizer etc as required.

Supply, laying & Fixing of Microphone Lines High grade, professional, Low-noise, 2-Core High conductivity PVC insulated in PVC Jacket, Shielded, copper cable with Di-electric insulator both end with XLR m/f connector as required.

Supply, laying & Fixing of Speaker Lines: 2-Core, 2.5 sq mm High definition Speaker Cable, PVC insulated in PVC jacket laid in existing conduits as reqd.

Supply Installation testing & Commissioning of Junction Box, etc complete as required.

Providing and fixing Main Curtain, Centre Parting Horizontal moving, motorised with min. 1.0 HP,3 phase, 415V 50Hz, AC motor, complete with Velvet Curtain duly stitched with pleats decorative strips, without linning, as required. strips, without linning, as required.

Providing and fixing Rear Curtain Horizontal moving, motorised with min. 1.0 HP,3 phase, 415V 50Hz, AC motor, complete with Velvet Curtain duly stitched with pleats decorative strips, without linning, as required. strips, without linning, as required.

Providing and fixing Main Frill bar, fixed type, made out of 25mm dia Ms pipe, supported from ceiling Structure, as required. Frill to be made out of Velvet cloth, stitched with pleats, frills, etc., as required.

Providing and fixing Frill bars, fixed type made out of 25mm dia GI pipe, supported from ceiling structure, As required, Frill to be made out of Black Glazed Cotton Cloth, stitched with pleats,Frills, etc., as required.

Providing and fixing Side Wings made out of Black 50x25 mm MS rectangular tube frame covered with Black Glazed Cotton Cloth

SITC of fixed light bar suitable for hanging of stage lights. made out of 48dia x5mm thick M/S pipe including all fixing arrangement as clamps, Craft ’hardware with powder painting complete as required as per side condition

Providing and Fixing Cyclorama Screen in Plastic Material. The screen to be fixed on tubular frame made out of 40mm dia MS pipe and Cross MS Pipe 25mm etc as required

SITC of LED profile 200w 36* voltage 0-90-250v/50- 60hz,working position: Any safe working position, lamp: super high power LEDs; white 180w (cool white or warm white) average life time is over 5000h,CRI:90, Lens angle :19*/26*/36*,optinal, LED display channel-2 ch,IP rate :IP 20 indor, speacial zoom funcation with manual adjustment, control mode: master /slave synchronization, DMX 512 control and automatic ,run,construcation:die-casting aluminium housing silver white and black,optinal. all complete as per direction of Engineer In Charge

SITC of LED cob par LIGHT 200w 4 led (Warm white optional) LED 4,6,7,9,3 DMX channel, End to end capability digital display,Angle 25* (optional 30*,45*)Dimmer 0-100% linerly Adustable strobe:-0-20F.P.S.,IP rating :- IP65,Control :-512,Ac Power: 90-100v Auto Sensing,power con in and oout, power consumption:100w ,DMX Data in/out 3 pin XLR. all complete as per direction of Engineer In Charge .

SITC of LED cob par LIGHT 200w 4 led (Warm white optional) LED 4,6,7,9,3 DMX channel, End to end capability digital display,Angle 25* (optional 30*,45*)Dimmer 0-100% linerly Adustable strobe:-0-20F.P.S.,IP rating :- IP65,Control :-512,Ac Power: 90-100v Auto Sensing,power con in and oout, power consumption:100w ,DMX Data in/out 3 pin XLR. all complete as per direction of Engineer In Charge .

Supply,Installation, testing & commisioning of LED Blinder 4way Light sources:DWE 120v 650w x4,Power supply: Ac 220v-240v/50hz,DMX channel:-1 channel Dimmer. all complete as per direction of Engineer In Charge.

Supply,Installation, testing & commisioning of Moving Head Sharpy Light 230w,POWER SUPPLIES 110-240V 50/60 Hz ,INPUT POWER,LAMPSOURCE Discharge lamp with a short arc burner in a reflector system - Type: YODA MSD Platinum 7R,- Output Lamp power: 230W- Colour temperature: 8,500 K,- Average life: 2,000 h OPTICS,3-lens optical group combination,Focus: electronic Light output at 20 meters (65 feet): 59,760 lux,COLOR SYSTEM Interchangeable color wheel with 14 colors + open EFFECTS SECTION,I nterchangeable gobo wheel with 17 fixed gobos + open,High speed shake effect,8-face rotating prism SHARPY 23,Frost filter,Mechanical shutter and adjustable speed strobe effect,Mechanical dimmer,CONTROL AND PROGRAMMING 16 DMX 512 control channels SOURCE Discharge lamp with a short arc burner in a reflector system - Type: YODA MSD Platinum 7R,- Output Lamp power: 230W- Colour temperature: 8,500 K,- Average life: 2,000 h OPTICS,3-lens optical group combination,Focus: electronic Light output at 20 meters (65 feet): 59,760 lux,COLOR SYSTEM Interchangeable color wheel with 14 colors + open EFFECTS SECTION,Interchangeable gobo wheel with 17 fixed gobos + open,High speed shake effect,8-face rotating prism SHARPY 23,Frost filter,Mechanical shutter and adjustable speed strobe effect,Mechanical dimmer,CONTROL AND PROGRAMMING 16 DMX 512 control channels SOURCE Discharge lamp with a short arc burner in a reflector system - Type: YODA MSD Platinum 7R,- Output Lamp power: 230W- Colour temperature: 8,500 K, Average life: 2,000 h OPTICS,3-lens optical group combination,

Focus: electronic Light output at 20 meters (65 feet): 59,760 lux,COLOR SYSTEM Interchangeable color wheel with 14 colors + open EFFECTS SECTION, Interchangeable gobo wheel with 17 fixed gobos + open,High speed shake effect,8-face rotating prism SHARPY 23,Frost filter,Mechanical shutter and adjustable speed strobe effect,Mechanical dimmer ,CONTROL AND PROGRAMMING 16 DMX 512 control channels ,Display: LED RED Display Pan/Tilt Resolution: 16 bit,Movement control: vectorial DMX signal connection: 3 PIN output,BODY,Aluminium structure with die-cast plastic cover.Two side handles for transportation. Device locking PAN and TILT mechanisms for transportation and maintenance. MOVING BODY.Travel:- PAN = 540° - TILT = 50°ELECTRONICS, Function reset from the lighting desk ON/OFF lamp control from the lighting desk" AUTOTEST" function from menu Electronic monitoring with status error SAFETY DEVICES Bipolar circuit breaker with thermal protection. Automatic break in power supply in case of overheating or failed operation of cooling system. Forced ventilation with axial fans.Hanging system: with fast-lock omega clamps (1/4 turn) on the base. all complete as per direction of Engineer In Charge

SITC of Channel DMX Splitter:Supply of DMX SPLITTER WITH ONE INPUT AND SIX OUTPUTS WITH COMPLETE INTERNAL WIRING AND ALL OUTPUT ELECTRICALLY ISOLATED FROM INPUT. Splitter shall be suitable for one DMX universe and all connections shall be through 3/5 pin XLR connectors complete with electrical input wire etc all complete as per direction of Engineer In Charge.

SITC of Digital Lighting Console with 1024 DMX channels • 1024 Channels. • 96 Fixtures. • 96 Dimmer Control Channels. • Time control of scenes: Fade in/out, LTP slope • Channels for each fixture 40 primary + 40 fine tune • LCD display with back light • 60 Scenes/Playbacks • 10 Scenes to run simultaneoulsy • 600 Scene step • Shape generato: Shapes of Dimmer, Pan/Tilt, RGB, CMY, Color, Gobo, Iris and Focus • Master slider - Global, playback, fixture • USB Memory - FAT32 supported

SITC of DMX Point Wiring complete with 2 core 23/0.2 Cu PVC sheathed sheilded cable having impedence not less than 100 ohm from splitter to light fixtures & between light fixtute to light fixture as required

Supplying & laying of Light Point Wiring from MCB Box to be provided near stage to various stage light fixtures with 1.5 Sq.mm 3 Core PVC insulated and PVC Sheathed copper conductor Cable including Cable Tray of suitable size for laying these wires on the tray including 16 amps sockets with box at top etc. complete as reqd

Supplying & laying of Clamp, etc complete as required.