Public Works Department Tender

b. Dumping stone including cost of stone in horizontal on level to be used in plum concrete.

Brick work with F.P.S bricks of class designation 75 in foundation and plinth in cement mortar 1:6 [ 1cement : 6 coarse sand] [Incl. all carriage loading & unloading with complete job]

Extra for brick work in superstructure above plinth level up to floor V level. (By manual means).

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:2:4 ( 1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) [Incl. all carriage loading & unloading with complete job]

Reinforcement for RCC work incl. straitening, cutting, binding, placing in position and binding all complete Thermo mechanically treated bars

Centering & shuttering incl. strutting, propping etc. and removal of form for a. foundations, footings, bases of columns etc. for mass concrete

b Suspended floors, roofs, landings, balconies and access platform.

6mm plaster to ceiling of mix 1:3 [1cement: 3 fine sand] [Incl. all carriage loading & unloading with complete job]

12mm cement plaster of mix 1:4 [ Cement : 4 coarse sand] [Incl. all carriage loading & unloading with complete job]

15mm plaster on rough site of single or half brick wall of 1:6 mix [1cement: 6 coarse sand]. [Incl. all carriage loading & unloading with complete job]

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 60x60cm [Incl. all carriage loading & unloading with complete job]

Providing and laying/ fixing Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITCO, ORIENT, KAJARIA, SOMANY or equivalent make in colour shades except White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete [Incl. all carriage loading & unloading with complete job]

Providing and fixing 1st quality ceramic glazed tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Eningeer in- Charge in skirting, risers of steps and dados over 12 mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarsesand) and jointing wtih grey cement slurry@ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.[Incl. all carriage loading & unloading with complete job]

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) a.Polyester powder coated aluminium (minimum thickness of polyester powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges I pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber I neoprene gasket required (Fittings shall be paid for separately.) b. Powder coated aluminium (minimum thickness of powder coated 50 microns)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) a. With float glass panes of 5.50 mm thickness (weight not less than 13.50 kg sqm)

b. With float glass panes of 8 mm thickness (weight not less than 20.0 kg sqm)

Providing and fixing 12mm thick prelaminated part- icle boardflat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and in -eluding priming coat with cement primer

Finishing walls with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/1 Osqm over and including base Coat of water proofing cement paint applied @ 2.20kg/1 Osqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo em,possed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot" and single piece M.S. sheet outer box with slide plate etc. complet~ as per the direction of Engineer-in- charge a. With brass cover plate minimum 1.25 mm thickness

Providing and fixing aluminium tubular handle bar 32mm outer dia, 3.0mm thick & 2100 mm long with SS screw etc. complete as per direction of Engineer-in-charge Powder coated minimum thickness 50 micron aluminium tabular handle bar

Providing and fixing 100 mm brass locks (best make of approved quality)for aluminium doors including necessary, cutting and making good etc complete

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, including cutting and making good the walls etc.: a. 15 mm dia. nominal bore Medium

b. 20 mm dia. nominal bore Medium

Providing and fixing white vitreous china pedestal type water closet ( European type) with seat and lid , 10 litre low level white vitreous china flushing cistern and CP flush with fittings, C. I./M.S. brackets 40mm bend diameter flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with lSI marked white solid plastic seat and lid. with white vitreous china flushing cistern & C. P. flush bend.

Providing c;1nd fixing wash basin with C. I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: (A) White Vitreous China White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing Salem Stainless Steel A lSI 304 (18/8) kitchen sink as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:610x510mm bowl depth 200mm

Providing & fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete 32mm dia

Providing and fixing mirror of superior glass( of approved quality) and of required shape and size with plastic .moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C. P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 a) 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. a) 15 mm nominal bore

Providing and fixing C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 a) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and gyser points _of approved make conforming to IS : 8931 a) 15 mm nominal bore

Providing and fixing C.P. brass close hole basin mixer piller tap of approved quality and make, weighing not less than1.970 kg. a) 15 mm nominal bore of standard back type

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license].

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion (i) Single socketed pipes a. 75 mm diameter

b. 110 mm diameter

Providing and fixing on wall face unplasticised- PVC moulded fittings/accessories for unplasticised- Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 1 0 mm gap for thermal expansion. a. 75 mm bend

b. 110 mm bend

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws@ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as epr requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment)

Providing and fixing gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels Granite of any colour and shape (Area of slab upto 0.5 sqm) [18mm thick] [Incl. all carriage loading & unloading with complete job]

Providing and laying integral cement based water proofing treatment including prepration of surfaces as required for treatment of roofs, balconies, terracies etc consisting of following operations. [Incl. all carriage loading & unloading with complete job] a) applying a slurry coat of neat cement using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement: 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. d) finishing the surface with 20mm thick jointless cement e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurra as 65 mm.