Public Health Engineering Department Tender

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6

Dumping of stones in horizontal including supply of stones

Making plinth protection 50mm thick of cement concrete 1:3:6 (1cement: 3coarses and:6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

Providingandlayingdamp-proof Course 50mm thick with cement concrete 1:2:4(1cement:2 coarses and:4 graded stone aggregate 20mm nominal size)and curing complete.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 (1cement:6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in super structure above plinth level upto floor five level

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°,landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiralstair cases upto five level including curing but excluding the cost of centring, shuttering,finishing and reinforcement with 5.3.1 1:1½:3 (1cement: 1½coarse sand:3 graded stone aggregate 20mm nominal size)

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level

Centering and shuttering including strutting, propping etc. and removal of form work for foundation footing etc.(any thickness) including attached pilasters buttresses, plinth below ground level.

Centering and shuttering including strutting, propping etc. and removal of form work for walls,walls (any thickness) including attached pilasters buttresses, plinth and string course fillets,kerbs and steps etc. above ground level.

Centering and shuttering including strutting, propping etc.and removal of form for Shelves (cast-in-situ)

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls

Centering and shuttering including strutting,propping etc.and remova lof form for Lintel,beams,plinth beams,girders,bressumers and cantilevers.

Filling with available fly ash and earth (excluding rock) in trenches or embankment inlayers (each layer should not exceed 15 cm), with intermediate layer of compactedearth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides& toplayerof filling shall be done withearth having total minimum compacted thickness 30 cm or as decided by Engineer-in-charge

12mm Cement plaster of mix: 1:4 (1 cement :4 fine sand)

15mm Cement plaster on the rough side of single or half brick wall of mix 1:6(1 cement :6 fine sand)

6mm cement plaster to ceiling of mix 1:3 (1 cement:3 fine sand)

Painting top of roofs with bitumen of approved quality at 17kg per 10sqm impregnated with a cost of coarses and at 60cudmper 10sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oi lcomplete

10cm thick (average) mud phaska of damped brick earth on roofs laid toslope consolidatedandplasteredwith25 mm thick mud mortarmixedwith bhusa at 35kg per cum of earth and gobri leaping with mix 1:1 (1clay: 1 cow dung) and covered with specified tile bricks grouted withcement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finishing neat.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarsesand: 4 stone aggregate 10 mm and down gauge), including finishing withcement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75mmdeepchase.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 gradedstoneaggregate) finished with a floating coat of neat cement including cementslurry and curing complete, but excluding the cost of nosing of steps etc 50mm thick with 20mm nomina size stone aggregate.

Providing wood work in frames of doors, windows, clerestory windows andother frames, wrought framed and fixed in position with hold fast lugs or withdash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately Salwood

Providing and fixing wire gauze shutters using galvanized M.S.wire gauze of average width for aperture1.4 mm in both directions with wire of dia.0.63 mm for doors,windows and clere story windows with ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge: Second class deodarwood 35mm

Providing and fixing panel led or panel led and glazed shutters for doors, windows and clere story windows fixing with butt hinges of required size with necessary screws,excluding panelling which will be paid for separately,all complete as per direction of Engineer-in-charge. 35mm Second class deodarwood

Steel work welded in built up sections/framedwork,includingcutting,hoisting, fixing in position and applying a priming coat of approved steelprimerusingstructuralsteeletc. asrequired. 10.25.1 In stringers, treads, landings etc. of stair cases, including use of cheque red plate wherever required,allcomplete.

Providing and fixing steel railing over stair case having height 3ft. With pillars and diagonal basis of approved brand all complete (as per direction of Engineer-in-charge LMR Rate)

Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings/wooden frames withrawl plugs screws etc.

Providing and laying Polished Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stone slabover 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing,curing and polishing etc.all complete as specified and as directed by the Engineer-in-Charge.

Tile work in skirting, risers of step and dedo upto 2 metre height, over12mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) andjointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigmen to fmatching shade complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622(thickness to be specified by the manufacturer), of approved make, in all colours, shadesexcept burgundy, bottle green, black of any size as approved by Engineer- in-Charge

Providing and laying vitrified floor tiles in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08%and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar1:4(1cement:4coarsesand)including grouting the joints with white cement and matching pigmentsetc.complete Size of tile 600x600mm

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc.including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge GraniteWork.

Providing and fixing false ceiling at all height including providing andfixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mmwidex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centreto centre, one flange fixed to the ceiling with dash fastener 12.5 mmdiax40mm long with 6 mm dia bolts, other flange of cleat fixed to the anglehangers of25x10x0.5mm of required length with nuts & bolts of requiredsize and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running atthe spacing of 1200 centre to centre,to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5 mm at 450mmcentre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm highhaving flanges of 20mm and 30 mm long, the perimeter of ceiling fixed towall/partition with the help of rawl plugs at 450 mm centre to centre, with25mm long drive-all screws @230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c,including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes,finishing with jointing compound in 3layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, allas permanufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cut outs made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 12.5mm thick tapered edge gypsum moisture resistant boar

Colour washing such as green blue or buffto givean even shade New work (two or more coats)with a base coat of white washing with lime

Finishing walls with water proofing cement paint of required shade on Newwork(two or more coats applied @3.84kg/10sqm)

Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade.Two or more coats on new work

Providing corrugated G. S. sheet roofing including vertical/curved surfacefixed with polymer coated J or L hooks, bolts and nuts 8mm diameter withbitumen and G.I limpet washers or with G.I. limpet washers filled withwhite lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal /vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cuttingt of size and shape wherever required. 0.63mm thick with zinc coating notless than 275gram/m2.

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I.limpet and bitumen washers complete 0.80mm thick with zinc coating notless than 275gram/m2

Providing and fixing rolling shutters 80x1.25mm M.S.laths with 1.25mm thick top cover

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion 110mm dia metre

Providing and fixing nickel plated M.S.pipe curtain rods with nickel plated brackets 25mm dia (heavy type)

Providing and fixing ISI mark edoxidized M.S.pressed butt hinges with necessary screws etc.complete: 100x58x1.90mm

Providing andfixing IS:1341 marked M.S.heavy weight-Butt Hinges with necessary screws etc.,complete: 125x90x4.00mm

Providing and fixing ISI markedoxidized M.S.handles conforming to IS:4992 with necessary screws etc. complete: 125mm

Providing andfixing aluminum handles ISI marked anodized (anodic coatingnot less than grade AC 10 as perIS: 1868) transparent ordyed to required colour and shade with necessary screws etc.complete: 100mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete: 200x10mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete: 100x10mm

Providing and fixing aluminum hanging floor door stopper,ISImarked,anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete: Single rubber stopper

Providing and fixing aluminum hanging floor door stopper,ISImarked,anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete: Twin rubber stopper

Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6mix (1cement: 3coarses and: 6graded stone aggregate 20mm nominal size).

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35kg and door width upto 700mm),with necessary accessories and screws etc.complete:

Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body,door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete:

Providing and fixing oxidized M.S. casement stays (straight peg type) with necessary screws etc.complete. 250mm weighing not less than 150gms.

Carriage of sand and stone aggregate average distance 20km by Mechanical transport to site of work

Carriage ofsoling stone average distance 20km by Mechanical transport to site of work

Carriage of bricks average distance 10km by Mechanical transport to site of work

Carriage of bricks tiles average distance 10km by Mechanical transport to site of work

Providing & fixing sanitary installation like water closet 03 Nos., urinals with flushing system 04 Nos. , washbasin 03 Nos., kitchen sink 01 No., labortory sink 01 No., water tank 02 Nos. sintex 2000 ltrs. each , Geyser 02 Nos., G.I/C.I/PVC fittings of bathrooms, kitchens etc. and all other allied works pertaining to sanitation of approved brand(as per the direction of Engineer Incharge.)

Providing & fixing electrification internal and external with high power/low power points including the cost of internal and external pvc fittings, boards, switches, mcb, copper wires including service line, tube light, bulbs, fans, exhaust fans flood lights and earthening etc. and all other allied works pertaining to electricfication module fitting of approved brand (as per the direction of Engineer Incharge.)

Providing & fixing Air Conditioner 04 Nos. having capacity 1.5 ton, Refrigrator having 615 ltrs. capacity 02 Nos. including transformers and allied accessories of approved brand with complete job (as per the direction of Engineer Incharge.)