Pradhan Mantri Gram Sadak Yojana Tender

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type B or as per Technical Specification Clause 508.By Mechanical Means Bitumen (S-90) including all leads, lifts and carriages of materials by MT complete.

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 , by mechnical means Bitumen (S-90) including all leads, lifts and carriages of materials by MT complete.

Making up loss of material/irregularities on shoulders to the design level by adding fresh approved selected soil and compacting it with appropriate equipment at OMC upto a lead of 1000 m as per technical specification Clause 1903

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 Ordinary Kilometer Stone (Precast)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 200 m stone (precast)

Providing and erecting direction and place identification of semireflective sign boards as per IRC:67 made of 2 mm thick M.S sheet duly stove enameled paint in white colour in front and gray colour on back with red reflective border of 70 mm width and required message,letter,figure with reflective tape of engineering grade as per MORD specification of required shade and colour supported and welded on two nos 47mmx47mm of 12 SWG Square tube of 3050 mm height duly strengthened by 25 mmx5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450mmx450mmx600mm,600 mm below ground level as per approved drawing and technical specification clause 1701.(Semi reflective Traffic sign): Direction &Place Identification Signs more than 0.90 Sqm Sign Boards.

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Construction of Un-Lined Surface Drains of averages cross-sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions Excavated material to be used in embankment with a lift upto 3m and lead of 50m (average lead 25 m ) as per Technical Specification Clause 307.Ordinary Soil 60% Ordinary Rock 40%