Power Development Department Tender

Supplying and fixing of 3 No. sub station earthing by way of Excavation of Earthing Pit of Dia 650mm Dept 3000mm and instllation of GI Pipe 40 mm or GI Rod 20mm, 2.5 mtr long as per IS 1239 through GI Strip of 50X6 mm 1 no for neutral earthing and 25X3 mm 2 nos (for 2 transformer body earth, two no. pole earth, 1 no. LA Earth and 1 no. GO handle earth). Note: For LA Earth 1 pipe shall be kept separate as per IS Standard 2629/85 GI Nuts & Bolts refilling with Earth enhancement materials and earthe Chamber made of Brick Massionary with RCC Slab Cover (Distribution Sub Station)

Supply and installation of Gapless Surge Arrestor,9 kV,10 kA, LA with (polymer) housing, Station Type

Supply and installation of 11 kV, G.O AB Switch , 3-phase, 200A

Supply and installation of 11 kV Horn, Gap Fuse 3-phase 100A

Supply and fixing of Un Armoured Single Core XPLE, FRLS Cable including Lugs for connecting 185mm2 (Reputed /Standard Make)

Supplying and erection of GI Channel 100x50x6mm V-cross-arm (75 x 40x6mm) with GI Angle Pole Top Bracket (50x50x6 mm) including back clamps of 50X8 mm for fixing Cross arm and F-top bracket without making holes in the ST pole as per REC standard for single pole structure. as per IS Standard

Supply and laying of Cement bottoming 1:2:4 mix as per REC standards 0.45 cum/pole, muffing 20 cm above ground level ,including plaster and curing of concrete in size of 600x600x1700mm for 9/8 mtrs Long ST Poles (410, SP-15) (the leftover pit after concreting to be filled with soil and boulders) as per IS Standard

Supplying and fixing of pole Earthing Complete by GI Pipe 40 mm 2.5 mtr long through GI Strip(25x3) to each HT pole including supply and welding of GI channel 70x40x150 on pole for earth connection as per IS Standard

Supply, installation, Loading, Transportation, insurance, Unloading, Carriage and Delivery at Site 11 KV Polymeric Composit pin with insulator insulator 12 KV, 5 KN,Light Impulse 75 KVPositive and 80 KV Negative ,Creepage distance 320 mm as per IS Standard

SITC 11kV Polymeric composite Disc Insulator 12V min failing load 45KN, Lighting Impulse 75kV Positive and 80kN Negative Creepage distance 320mm as per IS Standard

Supply, Installation of LT Distribution Box for 63kVA DTR with 160 Amp MCCB 3P 25-36 kA for incomer & SFU's for Outgoing Circuits including Bus Bars for Outgoing Circuits as per IS Standard

Supplying and fixing of Galvanized Nuts and Bolts of sizes as per IS Standard

Supplying and erection of Danger Plates with clamps with writing in English and Regional Language as per IS Standard

Supply and fixing of anti-climbing GI Barbed wire binding with Clamps at a distance of 30 to 40 cm at a height of 3.5 to 4 m from ground level. At-least 2 kgs GI barbed wire(12 SWG) is to be used per pole for the purpose. as per IS Standard

Supply and painting of each Pole 1 coat red oxide paint and 2 coats of aluminium paint (@ 1 ltr/pole red oxide paint and 1 ltr/pole aluminium paint) as per IS Standard

HIGH Mast Tower Supply , Installation , testing and Commissioning with transpotation at site of polygonal shape 12.5 mtr High mast pole (BPP/Utkarsh /Bajaj/phillips /Havells or equivalent make) with its accessories. Mast shaft shall be in two section, made from H.T. Steel of grade BSEN10025,S355JO hot dip galvanised and suitable for wind speed 180 km/hr as per IS 875. It should also included acc. for hight mast including head fame, two contineous steel wire rope mm ( Grade AISI 316), tailing cable,, double drum winch galvanised lantern carriage arrangement suitable for 6/4 nos. luminaries installation symmetrically and its control gear box, motor, manual operating handle, motor mounting plate, L staper , Lightening arrester , Junction box, including foundation acc. the mast shall have an intigral power tools installed inside the base compartment for its operation. Luminaries wiring matrials including in the mast supply price. Technical Specification. Bottom 340 mm, top- 150 mm thick , 3mm (bottom and top both) section - 2nos, length 6500 mm (Bottom), Baseplate 540 mm dia, baseplate thickness- 25 mm. hole dia- 26 mm, foundation bolt size 24 mm dia Bolt length 850 mm, No of hole 6 nos. Foundation bolt 6 nos. Wire rope 6mm SS 304 grade (Reputed /Standard)

Providing , Construction of suitable shallow foundation with 1:2:4 or M20 grade concrete for the high mast considering the safe soil bearing capasity at site as 10T/sqm. At 2X2 mit. Depth with all materials and labour charges.

Supplying and erection of LED avition obstruction light Lumainair(Reputed /Standard)

Supplying and fixing double door MS feeder piller box with near the high mast tower (Reputed /Standard)

Providing the following component ( switching acc.) inside the fidder piller including internal wiring all. Complete for autometic , timely OFF/ON for operating of (6 to 8 nos) 180 LED lighgting fitting. i)63 A 4 pole MCB isolater 1 no. ii)240 V contractor- 1 no. iii) Day dial timer (GIC)- 1 no iv) By pass switch- 1 no v) outlet Terminal - 2 nos. vi) Starter for moter operation (Forward and Revers direction )- 1no (Reputed /Standard)

Sullpy of LED flood light fixture (180watt) IP66 (Reputed /Standard)

Supplying and erection of Earthing station with 50 mm dia. GI pipes 3.65 mm thick, 3M long and 1no. 4 SWG G.I wire 4 M long, 13mm dia, 80 mm long G.I bolt double washers, nuts, S&F 15 mm dia G.I pipe protection , to be field with bitumen, partly under ground and partly above above ground level driven to an avarage depth 3.65 m below the ground level including excavation of soil

Supplying and drawing 4 core 10 sqm pvc insulated and scheathed alluminium conductor armoured cable through under ground (Reputed /Standard)

Supplying and fixing 32A, 450 TPN main switch on iron frame on wall and making connection (Reputed /Standard)

supply and fixing of 32A MCB with fitting complete (Reputed /Standard)

SITC of 8.0 mtr Long GI (65 micron DFT single dip) octogonal poles uniformally tappered with thickness of 3mm with bottom/top Dia of 155 mm x 70mm & base plate of 260x260x16mm/pcd 250 mm provided with proper door opened gear box for connections on the bottom side with G.I. Foundation Bolts (J Type) M20x700 mm long (Set of 4 no.’s per pole)

SITC of Laying of RCC foundation for 8.0 mtr. Long Octagonal poles including proper curing. 0.585mX0.585mX1.0m (RCC with concrete ratio 1:1.5:3 with minimum 8 Nos. of 12 mm dia longitudinal MS reinforcement rods with rings of 8 mm dia not more than 200 mm C.C for fixing the pole).as per IS Standard

SITC of Earthing of Octagonal Pole Complete by GI Pipe 40 mm or GI Rod 20mm 3 mtr long through GI Strip (25x3)mm as per IS Standard

SITC of Pre fabricate galvanized single way top bracket (1000mm long with 48.3 OD GI Pipe) to be fitted on top of Octogonal pole for holding lighting as per IS Standard

SITC of Pre fabricate galvanized two way top bracket (1000mm long with 48.3 OD GI Pipe) to be fitted on top of Octogonal pole for holding lighting as per IS Standard

SITC of DK thermoplastic cable Junction/ Termination T boxes 8"x10"of class IP55/IP65 fitted with two 2-5 Amp MCB strip,4-way terminal block / connectors Incl. copper lugs, Clamps ,nut & bolts washers etc (Hansel or equivalent make) or poles with two way type bracket to be fitted properly inside the door opened gear box provided on the bottom side of the pole.

Supply installation testing and commissioning of 80-120 Watt LED Luminaries of IP 66 protection with inbuilt Surge Protector for the 80-120 watt LED type lighting fixture complete. (Reputed /Standard make)

SITC of 2.5 mm 2 PVC insulated multistrand flexible copper wire for service connections from connection plate to the LED luminary indidual circuit including loop & earthings laid properly.(Reputed /Standard make)

SITC of HDPE pipe 50 mm O/D and inner Dia 38 mm including trench excavation in hard soil (0.3x0.45x1000m) for laying of 25/16 sq mm Almunium armoured cable . The job further inludes refilling back the same and removal of surplus excavted material to an appropriate place. (Reputed /Standard make)

SITC LT 25 mm2 2- core Aluminium XLPE Armoured cable to be carried through HDPE pipe U/G excluding cost of pipe & trench excavation. The cable shall include end termination lugs with its crimping /taping.

SITC LT 16 mm2 2 core Aluminium XLPE Armoured cable to be carried through HDPE pipe U/G excluding cost of pipe & trench excavation. The cable shall include end termination lugs with its crimping /taping.(Reputed /Standard Make)

SITC of Outdoor type LT control panel size 900mmX900mmX450mm having input main control of 100Amp MCCB with TPN Bus Bar with 40 Amp TPN MCB 4Nos for outgoing circuits,including astronomical switching with contactor of required capacity. The panel should be fitted with a digital composite voltmeter/ampermeter/indicator set with selecter switch and backup protection system, thimbling and the panel shall further be provided with proper openings on front side as well as on rear side including its locking arrangement and also with required glands and 4No. angle iron legs for grouting the panel on bed , the panel shall also be provided with powder coat/PU paint. The item includes its thimble as required at taping point for incomming , out going and internal panel wiring complete unit. (Reputed /Standard make)

SITC of Dust/rain/snow-proof canopy type mini-outdoor LT feeder panel of size 450X300mm with front door opening duly powdered colour coated with inbuilt 2No TPN 16-32 Amp MCCB,TPN busbars of same capacity installed on cement concrete block with 4 angle iron legs grouted in the cement concrete of termination of main 25sqmm cable and outgoing 25/16 sqmm cable circuits. (Reputed /Standard make)

SITC of Flexible Conduit of 25mm dia as per IS Standard

SITC 60 KVA 3 phase servo control stabiliser oil cooled with input voltage of 160-450 volts, 50 HZ and a constant out put voltage of 400 volt including the canopy of suitable size to protect during rains and snow. The Stabilizer shall be provide with high and low cut off voltage system, overload/under load single phase protection and also shall resist the input and out put +5% tolerance, the item includes cost of thimbling, lugs & other spares as required at input and output taping point. The Stabiliser shall be painted as per standards & of AE/Andrew Yule make with warranty period of two years from the date of Installation

Providing of Stencil and spray painting (black in Colour) on each pole at an height of 4.5 feet above ground levelwith following specification :- 1. The dimension of the stencil should be not less than 21"x 9" per Pole . 2. The following details are to be recorded on each pole with the spray paint. a. Name of the work b. Year c. Name of The contractor d. SR of the Pole. The said stencil should be approved by EDV Ganderbal.

Pre and post Geo tagged photographic Evidence consisting of 5x7 inch Photographs in coffee table book and autocad single line diagram