Power Development Department Tender

Supply, Laying, installation, testing and commissioning of 100 mm² ACSR 1. Site 1 - 9000 Mtr 2. Site 2 - 18000 Mtr

Supply, Fixing, Testing and commissioning of 11kV Polymeric composite Disc Insulator 12kV,min failing load 45kN, Lighting Impulse 75kV Positive and 80kV Negative, creepage distance 320mm 1. Site 1 - 30 No. 2. Site 2 - 50 No.

Supply, Fixing, Testing and commissioning of 11kV Polymeric composite Pin Insulator 12kV, 5kN, Lighting Impulse 75kV Positive and 80kV Negative, creepage distance 320mm 1. Site 1 - 100 No. 2. Site 2 - 200 No.

Supply, fabrication, installation, testing and commissioning of G.I Channel X/V crossarm Iron / Angle Iron /Flat of sizes including Top Bracket, clamps and collars. (As per KPDCL approved drawing) 1. Site 1 - 788.92 kg 2. Site 2 - 1770.62 kg

Providing & Laying of Pole Earthing Complete by GI Pipe 40 mm 3 mtr long through GI Strip 25x3 mm 1. Site 1 - 28 No. 2. Site 2 - 62 No.

Supply & Fixing of Galvanized Nuts and Bolts 1. Site 1 - 70 kg 2. Site 2 - 160 kg

Supply & Fixing of Danger Plates with Clamps 1. Site 1 - 28 No. 2. Site 2 - 62 No.

Supply & FIxing of Anti-Climbing Device with Clamps 1. Site 1 - 28 No. 2. Site 2 - 62 No.

Providing and painting of poles with single coat of red oxide an two coats of Aluminum Paint 1. Site 1 - 28 No. 2. Site 2 - 62 No.

Supply & Fixing of GI Wire 6 SWG & 8 SWG 1. Site 1 - 28 kg 2. Site 2 - 60 kg

Design, Fabrication, Supply, installation, testing and commissioning of 11kV Pilfer resistant metering cubicle for 3phase 4 wire metering system made of MS Sheet steel thickness not less than 2mm duly power coat painted suitable for indoor as well as outdoor as per the site requirement. The cubicle shall be painted through 7-tank process. The External dimensions should be adequate. Panel having two compartments upper Meter compartment and lower CT/PT compartment. Provided with synthetic or semi synthetic gasket firmly glued to the sufrace, Dust, weather and Vermin proof and shall comply degree of protection IP 65 both the chambers having one sided hinged door arrangments. The metering panel shall be provided with two No MS channels of size 100 x 50 mm on the front and rear sides duly welded and 4 No of lifting hooks. It should be possible to take meter reading manually, through CMRI and computer without opening the LV chamber door 1. Site 1 - 01 No. 2. Site 2 - 01 No.

Supply, installation, testing and commissioning of Single Phase, Single core, single ratio, Epoxy resin Cast Current Transformers suitable for 11kV, copper wound primary type with rated burden 5VA and accuracy class 0.5 or better and conforming to IS2705 (part-I & II) amended upto date. ISF shall be upto 5. The CT ratio shall be as under:. CT ratio:- i. 2.5 /5 for 25kVA DT ii. 5/5 for 63kVA DT iii. 7.5/5 for 100kVA DT iv. 15/5 for 200kVA DT v. 20/5 for 250kVA DT vi. 25/5 for 400kVA DT vii. 50/5 for 630kVA DT viii. 75/5 for 1MVA DT 1. Site 1 - 01 set 2. Site 2 - 01set

Supply, installation, testing and commissioning of 11kV/ 110 V, Three phase epoxy resin cast PT with rated burden 15VA per phase andaccuracy class 0.5 or better and conforming to IS:3156 (part-I&II) amended upto date with proper colour coded identification. PTs shall be of uniform insulating and withstand separate source 23 KV pf for one minute. 1. Site 1 - 01 set 2. Site 2 - 01 set

Supply, installation, testing and commissioning of Bus Bar as per details: CTs bus bar:- 40x6 mm copper strip or adequate size. PTs bus bar: Copper wire 8 SWG or 30x0.6mm copper flat strip to connect PT terminal or adequate size duly insulated by the monoplast tape.

Supply, installation, testing and commissioning of PVC Copper wire flexible multi-strand of required size for secondary connections for CT wiring the minimum wire size shall be 4 mm2 (RYB) and for PT wiring minimum wire size shall be 2.5 mm2 (RYB).

Supply and fixing of Copper Lugs preferably ring type duly crimped for termination of wires and tapes

Providing and fixing of Grounding bus of minimum 40mm copper, 25cm long fixed to the unit in HV chamber. The CTs, PT meter and 11 KV Cable sheath shall be grounded to the bus through grounding wire (green) of min size 10mm2.

Supply, installation, testing and commissioning of 3Ph, 3 Wire HT CT/PT operated Fully static Smart Tri-Vector Energymeters DLMS CompliantCategory 'C' with RS232 port for modem compatibility. 11kV/110V, Ph-Ph (3P,3W) metersfor measurement of different electrical parameters including Active Energy (kWh/ MWh), Reactive Energy (kVArh/MVArh), Apparent Energy (kVAh/ MVAh) etc. (make L&T, Secure,ABB)

Supply and fixing of Pedestal made out of G.I Channel of size 75 x 40 mm or angle iron of size (65 x 65 x 5) mm, duly painted as per site requirement for mounting of metering panel including concrete foundation wherever required including cost of nuts and bolts.

Supply and fixing of Independent flexible PVC pipes for CT wiring and PT wiring of appropriate size from HTcompartment to meter compartment

Supply, installation, testing and commissioning of 3 Core 11 kV Aluminium cable XLPE armoured 35 mm2 including cost of clamp for its fixing where ever required. 1. Site 1 - 20 Mtr 2. Site 2 - 20 Mtr

Supply, installation, testing and commissioning of Cable termination kits suitable for 3 x 35 mm2 XLPE Cable(indoor/outdoor) 1. Site 1 - 04 Set 2. Site 2 - 04 Set

Providing and laying of Earthing by way of 40 mm GI Pipe earthing for HT metering. Job includes , excavation, enhancement material and man Hole Chamber (500x450x600)mm with frame and cover. 1. Site 1 - 02 No. 2. Site 2 - 02 No.

Supply of material & Laying of Cement bottoming of poles (1:2:4 Mix as per REC Standards 0.48 M3 per Pole) 1. Site 1 - 28 No. 2. Site 2 - 62 No.