Police Department Tender

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin- charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineerin- plate etc. complete as per the direction of Engineer-in-charge With brass cover plate minimum 1.25 mm thickness

Providing and fixing of 3mm thickness APP (Atactic Poly Propylene Polymer ) Superthermoly STP sheet polyester based sheet black finishing including coats of silver paint with cemented surface by following method cleaning the surface with wire brush to make the surface free from all loose particles, dust etc then repairing / making the corner fillets dips with pidicrete URP 301 or equivalent water proofing compound in cement and sand mortar 12mm to 18mm thick and with PCC 1:2:4 mix. (I) Applying with shalitex STP primer for bitumen membrane @ 0.40 ltr/sq. mt. (II) Mt. by the 3mm thickness APP superthermoly STP black sheets polyester based sheet black finishing manufacture (III) Cut 1" deep groove above the roof surface on the groove with polymer modified mortar (IV) in case of low height parapets, terminate APP superthormoly STP polyester sheets pver the parapet (V) for over lapping of joints, rub the polythylene side of membrane by wire brush, apply shali bond APP over the ribbed area, alow it to the tackly and then fix the bitumenious side of APP superthermolySTP sheet polyester with hot application (VI) for longitudinal and tranverse joint pverlaps of 75mm and 100mm respectively id desired. the vital physical and chemical paramater of the membrane shall as under:- Siftening ppoint of membrane not less them 150*c cold flexiblity shall be upto 0"c when tested in accordance with ASTM, joint strengh in longitudunal and transverse direction at 1223*c as 350/300N/5cm. Tear strenght in longitudinal and transverse direction as 60/80N in 3mm thick, the weight of roll (40KG for 1 mtr bt 10 mtrs) the laying of membrane shall be got done through the certified applicator.

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead With cement mortar 1:4 (1 cement : 4 fine sand)

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 1 mm thick

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour Two coat

Finishing walls with Acrylic smooth exterior paint of required shade Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion (i) Single socketed pipes

110 mm diametre

Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

110mm dia PVC palin bend

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete 250x16 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 100x10 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 200x10 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete 125 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete 100 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete

Engagement of labour skilled/ unskilled for various dismantling works like tacking of floors, damaged tiles, etc including stacking of serviceable material as directed by EIC and disposal of unserviceable material up to 50 mtr lead.

Labour

Carpenter

Renewing glass panes, with wooden fillets wherever necessary Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)

Providing and fixing of 1'-4" to 2’-0” deep kitchen cabnets/ Almirah of approved design & make including shutters, partitioning with 19mm thick (water proof) ply board of approved make and quality including back covering of 0.7mm thick water proof ply and fixing 1mm thick mica of approved colour and make over the frame and shutter, as around including cost of all fixtures i.e. glazing, locking arrangements, handle etc. as per the directions of site Engineer. (complete Job)

Carriage of material by mechanical transport including all loading / unloading complete

Sand Aveg. lead of 20 Km

Providing and fixing of following types of switches, sockets, allied accessories including dismantling of existing switches and sockets with terminations as required Anchor/Legrand/GM/Crabtree or equivalent make

16A switch only piano type

16A socket only piano type

6A switch only piano type

6A socket only piano type

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in existing surface/ recessed steel/ medium class PVC conduit as required Finolex/Polycab/Anchor/V-Guard/Havells/RR kabel or equivalent make

2 x 1.5 Sqmm

2 x 2.5 Sqmm

2x 4 sqmm

Providing and fixing of following type of MCB's/switch gear of L&T/Havells/Anchor/ Schnedier/indoasian Opti-Pro/Legrand or equivalent make of 10 KA or more capacity series including testing and necessary terminations.

63 A SPN

6A-32A MCB's

Providing and fixing of LED lights of following type Crompton/Phillips/Orient/Havells/Syska or equivalent make including necessary terminations as required.

9 Watt LED Lamps

Providing and fixing of fan dimmers of piano type Anchor/Legrand/GM/Crabtree or equivalent make.

Providing and fixing of 48" Sweep ceiling fan with allied accessories complete including necessary terminations anchor/crompton/ Havells/Orient/Usha or equivalent make.

Providing and fixing of manual 63A changeover 240V box with handle

Providing and fixing of Angle/straight holders including terminations GM/Havells/Krant /Anchor/Great white make

Providing and fixing of Phenolic sheets of desired shapes and sizes incluting cutting, finishing, drilling etc.

Providing and fixing of following sizes of PVC battens along the wall or ceiling including dismantling of existing damaged battens.

1" wide surface batten 3 meter long