National Projects Construction Corporation Limited Tender

CONFERENCE CHAIRS - SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ± 0.1cm thk. hot pressed plywood OCP-QLTA-PL14-18.The Back should be made up of injection moulded glass filled nylon & upholstered using Net fabric with high tenacity yarn. SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D) BACK SIZE :45.0 cm. (W) x 65.3 cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. 3.ARMRESTS : The armrests have an Up-Down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure. Armrest Top has an integrated layer of Thermoplastic Elastomer (TPE). LUMBAR SUPPORT ASSEMBLY: The Lumbar support consshould be ts of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. FRONT PIVOT SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features. • 360° revolving type. • Single point control. • Front-pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat/back tilting ratio of 1:2. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia should be ∅66.1 ± 0.5 cm (76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black Nylon. The Neckrest assembly consshould be t of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest should be fixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0.5 cm and rotation adjustment of overall 76°± 2°. The complete neckrest assembly should be retro fit to the main chair.

SECURITY CELL, OFFICE & CABIN

SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE 47.5 cm. (W) x 69.5 cm (H) SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO mechanism: The mechanism should be designed with the following features: • 360° revolving type. • Upright-position locking • Tilt tension adjustment • Seat/back tilting ratio of 1:3. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLYThe bellow should be 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY:The pedestal should be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Nylon. Overall Dimensions of Chair Seat Height - min 42.5 to max 54.5cm. Height - min97.0 to max 109.0cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood. OCP-QLTA-P14.18 and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed with contoured lumbar support for extra comfort BACK SIZE: 41.0cm. (W) X 46.0cm. (H) ]SEAT SIZE: 43.0cm. (W) X 41.0cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR Polyurethane foam should be moulded with density = 45 ±2 kgs. /m3 and Hardness load 16 ± 2 kgf for 25% compression ARMRESTS : The armrest should be .made of black integral skin polyurethane with 50-70 Shore A hardness and reinforced with MS insert. The P.U. armrest should be fixed to black powder coated DFT 40-60 microns ) armrest bracket made of 0.5 ± 0.05cm. thk. HR steel. PERMANENT CONTACT mechanism: The permanent contact mechanism should be designed with the following features:- 360° revolving type 14° ±2° maximum back-tilt only. Upright position locking Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm TELESCOPIC BELLOW ASSEMBLY: The bellow should be 3 piece telescopic type and injection moulded in black Polypropylene PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet (should be :DD 10791 HR) , powder coated ( DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 55.0 ±0.5cm. pitch-center dia. (65.0 ±1.0cm with castors) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon Overall Dimensions of Chair Seat Height - min 42.0 to max 54.0cm. Height - min80.0 to max 92.0cm. Width & Depth of Chair as measured from pedestal - Width-65.0 cm and Depth-65.0 cm.

Finesse Table - 5026 size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. Finesse ERU -3616 LHS size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.

STORAGE CABINATE: Overall Dimensions of VSDU - 12 shall be 1200mm(W)x450mm(D)x1192.5mm(H) . The top shall be wooden top PLB(25 mm add in unit height ) . The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU - 12 shall have 4 no. of adjustable half shelves . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU 12 - A4 size box file can be stored vertically on two shelves and clear space above third shelf is 295 mm .

RECEPTION AREA

SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood. OCP-QLTA-P14.18 and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed with contoured lumbar support for extra comfort BACK SIZE: 41.0cm. (W) X 46.0cm. (H) ]SEAT SIZE: 43.0cm. (W) X 41.0cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR Polyurethane foam should be moulded with density = 45 ±2 kgs. /m3 and Hardness load 16 ± 2 kgf for 25% compression ARMRESTS : The armrest should be .made of black integral skin polyurethane with 50-70 Shore A hardness and reinforced with MS insert. The P.U. armrest should be fixed to black powder coated DFT 40-60 microns ) armrest bracket made of 0.5 ± 0.05cm. thk. HR steel. PERMANENT CONTACT mechanism: The permanent contact mechanism should be designed with the following features:- 360° revolving type 14° ±2° maximum back-tilt only. Upright position locking Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm TELESCOPIC BELLOW ASSEMBLY: The bellow should be 3 piece telescopic type and injection moulded in black Polypropylene PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet (should be :DD 10791 HR) , powder coated ( DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 55.0 ±0.5cm. pitch-center dia. (65.0 ±1.0cm with castors) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon Overall Dimensions of Chair Seat Height - min 42.0 to max 54.0cm. Height - min80.0 to max 92.0cm. Width & Depth of Chair as measured from pedestal - Width-65.0 cm and Depth-65.0 cm.

Top shall be of Rubberwood with clean Matt PU finish 18 mm thick , inside radius - 700 mm , outside radius - 1350 mm and depth - 650 mm . Cork shall be 18 mm thick of rubber . Glass shall be Frostered 10 mm thick diamond cut finishing on edges , inside radius shall be - 1202.5 mm , otside radius - 1402.5 mm and depth - 200 mm . The Modesty Panel shall be MS Perforated sheet below worksurface : 0.8 mm (thick) x 665 mm ( height) x 1345 mm (flat length ) . Above Worksurface : 0.8 mm (thick ) x 260 mm (height) x 1345 mm (flat length) . The legs shall be of MS tube 1.6 mm thick diameter 50.8 mm and height 604 mm

STORAGE CABINATE: Overall Dimensions of VSDU - 12 shall be 1200mm(W)x450mm(D)x1192.5mm(H) . The top shall be wooden top PLB(25 mm add in unit height ) . The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU - 12 shall have 4 no. of adjustable half shelves . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU 12 - A4 size box file can be stored vertically on two shelves and clear space above third shelf is 295 mm .

SOFA 2 SEATER - SEAT FOAM‎: ‎The seat is made of PU ‎foam with Density ‎28‎± ‎2 ‎kg‎/‎cu‎.‎mtr having an ‎additional top layer of super soft ‎PU foam in Density ‎32 ‎± ‎2 ‎kg‎/‎cu‎. ‎upholstered with fabric ‎or leatherette‎. ‎BACK ‎FOAM‎: ‎The back is ‎made of PU foam with ‎Density ‎28 ‎± ‎2 ‎kg‎/‎cu‎. mtr with two additional ‎top layer of supersoft ‎ foam of density ‎32‎±‎2 ‎kg‎/‎cu‎. ‎mtr‎, ‎upholstered ‎ with fabric or leatherette .UNDERSTRUCTRE ‎: ‎Understructure is made ‎up of ‎1‎.‎2‎±‎0‎.‎1 ‎cm‎. ‎thick ‎hot pressed plywood ‎( moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY‎: ‎It is ‎a welded assembly ‎made in Stainless steel ‎(‎grade SS ‎202‎) ‎tube ‎& ‎plate‎ with plastic endcap. (W) 146.0* (D) 90.5(H) 85.5 cm seat (H) 45.0 cm

SOFA 3 SEATER - SEAT FOAM‎: ‎The seat is made of PU ‎foam with Density ‎28‎± ‎2 ‎kg‎/‎cu‎.‎mtr having an ‎additional top layer of super soft ‎PU foam in Density ‎32 ‎± ‎2 ‎kg‎/‎cu‎. ‎upholstered with fabric ‎or leatherette‎. ‎BACK ‎FOAM‎: ‎The back is ‎made of PU foam with ‎Density ‎28 ‎± ‎2 ‎kg‎/‎cu‎. mtr with two additional ‎top layer of supersoft ‎ foam of density ‎32‎±‎2 ‎kg‎/‎cu‎. ‎mtr‎, ‎upholstered ‎ with fabric or leatherette .UNDERSTRUCTRE ‎: ‎Understructure is made ‎up of ‎1‎.‎2‎±‎0‎.‎1 ‎cm‎. ‎thick ‎hot pressed plywood ‎( moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY‎: ‎It is ‎a welded assembly ‎made in Stainless steel ‎(‎grade SS ‎202‎) ‎tube ‎& ‎plate‎ with plastic endcap. (W) 206.0* (D) 90.5(H) 85.5 cm seat (H) 45.0 cm

PISA CENTER TABLE: Glass should be 12 ±0.3 mm thick black tinted toughened glass uv glued with bushes made in ss 202 grade for fixing with under structure. Should be a center table under structure: it should be a welded assembly made in ss202 grade having dia. 12±0.04 as per should be: 1762. Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

TRAINING CELL & OFFICE

TABLE 5 FEET WORKTOP: Made of 25mm Thick Pre-laminated twin board interior grade of approved shade conforming to IS:12823, and Edge banded with matching 2 mm thick PVC lipping. Size shall be 1500x750mm. Modesty Panel: Made of 25mm Thick Pre-laminated twin board interior grade of approved shade conforming to IS:12823 and Edge banded with matching 2 mm thick PVC lipping. Under-structure: Legs are made of 50mm x 30mm x 1.6mm thk M.S. electric resistance welding tube as per IS:7138 and 10 mm thick HR steel as per IS 2062 welded together and powder coated with min 45 micron thickness of epoxy polyester coating. Modesty holding Leg frame is made of made of 50mm x 30mm x 1.6mm thk M.S. electric resistance welding tube as per IS:7138 and 3mm thick HR steel as per IS 2062 welded together and powder coated with min 45 micron thickness of epoxy polyester coating. Cross member assembly for top is made of made of 50mm x 30mm x 1.6mm thk electric resistance welding tube as per IS:7138 and 3 mm thick HR steel as per IS 2062 welded together and are powder coated with min 45 micron thickness of epoxy polyester coating Pull handle made of Ø16.0 x 1.2mm thk M.S. electric resistance welding tube as per IS:7138 , powder coated with min 45 micron thickness of epoxy polyester coating. Housing bracket assembly is made of 3 mm thick HR steel as per IS 2062 welded together and is powder coated with min 45 micron thickness of epoxy polyester coating. Housing bracket carries mechanism for folding table made of 10mm thick HR steel as per IS 2062. Understructure is provided with Ø 65mm lockable Castors for ease of movement and can be locked when required at any position. The OEM of the products must be ISO 9001, ISO 14001 and ISO 45001 certified. The certificate must be from an authorized issuing agency, verifiable in India by some Government agency like NABCB or NABET. The product must be either Greenguard or Bifma Level or IAQ or Griha certified. The certificate must be attached along with the technical bid. The certificate must mention the manufacturer's name as well as Model name. The certificate must be from an authorised issuing agency only. The certificate must be verifiable from the valid issuer's website.

Training Room chairs: The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT 40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-61.0 cm and Depth-64.5 cm. The OEM of the products must be ISO 9001, ISO 14001 and ISO 45001 certified. The certificate must be from an authorized issuing agency, verifiable in India by some Government agency like NABCB or NABET. The product must be either Greenguard or Bifma Level or IAQ or Griha certified. The certificate must be attached along with the technical bid. The certificate must mention the manufacturer's name as well as Model name. The certificate must be from an authorised issuing agency only. The certificate must be verifiable from the valid issuer's website.

1)SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) BACK SIZE : 45 cm. (W) x 60.5 cm. (D) 2)ARMRESTS The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk MS E.R.W tube. The armrest height adjustable up to 6.5±0.5cm in 5 steps.The Armrest structure should be powder coated (DFT 40-60 micron). 3)ACTIVE BIO-SYNCHRO mechanism (FU3401/3402): The adjustable tilting mechanism should be designed with the following features: • 360° revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of HPDC Aluminium black powder coated. 4)SEAT DEPTH ADJUSTMENT Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. 5) ADJUSTABLE BACK SUPPORTBack Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. 6) PNEUMATIC HT. ADJUSTMENT The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. 9) TWIN WHEEL CASTOR : 5 Nos. twin wheel castors should be injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal. The OEM of the products must be ISO 9001, ISO 14001 and ISO 45001 certified. The certificate must be from an authorized issuing agency, verifiable in India by some Government agency like NABCB or NABET. The product must be either Greenguard or Bifma Level or IAQ or Griha certified. The certificate must be attached along with the technical bid. The certificate must mention the manufacturer's name as well as Model name. The certificate must be from an authorised issuing agency only. The certificate must be verifiable from the valid issuer's website.

BUSINESS DEVELOPMENT

Work top Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access panels provided with soft closing hinges Understructure The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Management Bottom cabinet with door is provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg. HDMI,VGA-A,etc). Size of tables is 2400mmX1200mm (centre line dimensions).

The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height - min93.5 to max 104.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. The OEM of the products must be ISO 9001, ISO 14001 and ISO 45001 certified. The certificate must be from an authorized issuing agency, verifiable in India by some Government agency like NABCB or NABET. The product must be either Greenguard or Bifma Level or IAQ or Griha certified. The certificate must be attached along with the technical bid. The certificate must mention the manufacturer's name as well as Model name. The certificate must be from an authorised issuing agency only. The certificate must be verifiable from the valid issuer's website.

CABIN & PA

SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE 47.5 cm. (W) x 69.5 cm (H) SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO mechanism: The mechanism should be designed with the following features: • 360° revolving type. • Upright-position locking • Tilt tension adjustment • Seat/back tilting ratio of 1:3. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLYThe bellow should be 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY:The pedestal should be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Nylon. Overall Dimensions of Chair Seat Height - min 42.5 to max 54.5cm. Height - min97.0 to max 109.0cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood. OCP-QLTA-P14.18 and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed with contoured lumbar support for extra comfort BACK SIZE: 41.0cm. (W) X 46.0cm. (H) ]SEAT SIZE: 43.0cm. (W) X 41.0cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR Polyurethane foam should be moulded with density = 45 ±2 kgs. /m3 and Hardness load 16 ± 2 kgf for 25% compression ARMRESTS : The armrest should be .made of black integral skin polyurethane with 50-70 Shore A hardness and reinforced with MS insert. The P.U. armrest should be fixed to black powder coated DFT 40-60 microns ) armrest bracket made of 0.5 ± 0.05cm. thk. HR steel. PERMANENT CONTACT mechanism: The permanent contact mechanism should be designed with the following features:- 360° revolving type 14° ±2° maximum back-tilt only. Upright position locking Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm TELESCOPIC BELLOW ASSEMBLY: The bellow should be 3 piece telescopic type and injection moulded in black Polypropylene PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet (should be :DD 10791 HR) , powder coated ( DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 55.0 ±0.5cm. pitch-center dia. (65.0 ±1.0cm with castors) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon Overall Dimensions of Chair Seat Height - min 42.0 to max 54.0cm. Height - min80.0 to max 92.0cm. Width & Depth of Chair as measured from pedestal - Width-65.0 cm and Depth-65.0 cm.

Finesse Table - 5026 size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. Finesse ERU -3616 LHS size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.

Storage Cabinate: Overall Dimensions of VSDU - 12 shall be 1200mm(W)x450mm(D)x1192.5mm(H) . The top shall be wooden top PLB(25 mm add in unit height ) . The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU - 12 shall have 4 no. of adjustable half shelves . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU 12 - A4 size box file can be stored vertically on two shelves and clear space above third shelf is 295 mm .

STAFF CUBICAL

work station Panel Based partition Panel Based partition of 60mm thickness with framework made up of aluminiu alloy extrusions. All Aluminium parts are pretreated for epoxy polyester powder coated of 40-60micron thickness. All these frame work sections are fitted to each other by screws which is properly zinc coated for corrosion resistant. One single frame consists of following Components :- 1.Vertical Member in aluminum alloy extrusion (thickness 1.6mm). 2. Top Horizontal Member in aluminum alloy extrusion of size 60x30mm(thickness 1.3mm). 3. Mid Member in aluminum alloy extrusion of size 60x22mm (thickness 1.3mm) having provision to support the worktop with engineered design Support bracket. 4. Bottom Raceway in aluminum alloy extrusion of size 140mm ht. x 60mm (thickness 1.2mm). 5. Intermediate Raceway In aluminum of size 120mm ht above / below the work top as per requirement. 6. Tiles THE BOTTOM tiles can be provided in following options:- (a) Prelaminated Particle Board tile of 9mm thickness with decorative laminate on top and white balancing on unexposed face, The tiles are supported within groove in aluminium extrusion. (b)The Marker tile are made up of 9mm particle board pasted with 1mm white marker laminate, on the the exposed face The tiles are supported within groove in aluminium extrusion. (c) Fabric on board tile are made up of GI sheet of 0.8mm inside upholstered with response fabric supported with staple pins. The tiles are supported within groove in aluminium extrusion. 7.Top & End Trims -The exposed vertical and horizontal faces of the frames. The trims are made of aluminum extrusions of size 60x19mm(thickness 1.5mm) and are covered with ABS caps on joints and ABS end trims. 8.Connectors:--Partitions are supported by Universal poles & MS bracket of 2mm thick zinc plated wherever required i.e,(L,T,+,180deg) for stability. At 2 Way joint of 90deg- Aluminium alloy extrusion of 60x60mm is provided which is fitted to main frame and epoxy powder coated. At 3 way joint of 90deg- Aluminium alloy extrusion of 60x60mm is provided which is fitted to main frame and epoxy powder coated. At 4 way joint of 90deg- Aluminium alloy extrusion frame Vertical member is fitted with M S connectors at top and WIRE MANAGEMENT - Partition has concealed wire management capabilities and are engineered for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cutouts are provided on Raceways to fix all electrical and data points. LEVELLERS - Levellor of M10 size are provided in each frame which allow 10-25mm adjustment for floor unevenness. Table Top of 25mm thick made up of 25mm Pre-Laminated PLPB Board and Gable end made using 25mm Pre-Laminated PLPB Board with Specially designed Leveller bracket. Modesty made up of 18mm thick Pre-Laminated Board.Pre-Laminated PLPB Board Drawer Pedestal (2B+1F) 400Lx450Dx685Ht. Carcass & Facia made up of 18mm thick Pre-Laminated Board. Back Panel from 9mm PPB. All exposed edges are sealed with 1.5- 2mm thick PVC edge-band & Non-exposed edges with 0.8mm thick PVC edge-band of Rehau or equivalent. All the hardware & channels are from Hettich/Ebco.PVC recessed handles are provided for easy opening and closing of drawer. Size of staff cubicle is 1500mm x1500mm.

Meeting ROOM

Meeting Table 32 seat: Worktop shall be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Plastic ABS access flap is provided for easy access to wires and cables. Work top shall be as per layout. The Under-structure cconsist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction.. Modesty panel shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated. An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pullout audio,video cables onto worktop and connect devices charger to power socket below worktop. 2 STR MAIN ST - 1350 X 600 X 740 2 STR SHARED ST- 1350 X 600 X 740 The OEM of the products must be ISO 9001, ISO 14001 and ISO 45001 certified. The certificate must be from an authorized issuing agency, verifiable in India by some Government agency like NABCB or NABET. The product must be either Greenguard or Bifma Level or IAQ or Griha certified. The certificate must be attached along with the technical bid. The certificate must mention the manufacturer's name as well as Model name. The certificate must be from an authorised issuing agency only. The certificate must be verifiable from the valid issuer's website. Modules as per layout

Conference chairs Midback: The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height - min93.5 to max 104.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. The OEM of the products must be ISO 9001, ISO 14001 and ISO 45001 certified. The certificate must be from an authorized issuing agency, verifiable in India by some Government agency like NABCB or NABET. The product must be either Greenguard or Bifma Level or IAQ or Griha certified. The certificate must be attached along with the technical bid. The certificate must mention the manufacturer's name as well as Model name. The certificate must be from an authorised issuing agency only. The certificate must be verifiable from the valid issuer's website.

Conference chair - SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ± 0.1cm thk. hot pressed plywood OCP-QLTA-PL14-18.The Back should be made up of injection moulded glass filled nylon & upholstered using Net fabric with high tenacity yarn. SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D) BACK SIZE :45.0 cm. (W) x 65.3 cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. 3.ARMRESTS : The armrests have an Up-Down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure. Armrest Top has an integrated layer of Thermoplastic Elastomer (TPE). LUMBAR SUPPORT ASSEMBLY: The Lumbar support consshould be ts of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. FRONT PIVOT SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features. • 360° revolving type. • Single point control. • Front-pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat/back tilting ratio of 1:2. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia should be ∅66.1 ± 0.5 cm (76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black Nylon. The Neckrest assembly consshould be t of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest should be fixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0.5 cm and rotation adjustment of overall 76°± 2°. The complete neckrest assembly should be retro fit to the main chair.

Single Seater sofa - SEAT FOAM‎: ‎The seat is made of PU ‎foam with Density ‎28‎± ‎2 ‎kg‎/‎cu‎.‎mtr having an ‎additional top layer of super soft ‎PU foam in Density ‎32 ‎± ‎2 ‎kg‎/‎cu‎. ‎upholstered with fabric ‎or leatherette‎. ‎BACK ‎FOAM‎: ‎The back is ‎made of PU foam with ‎Density ‎28 ‎± ‎2 ‎kg‎/‎cu‎. mtr with two additional ‎top layer of supersoft ‎ foam of density ‎32‎±‎2 ‎kg‎/‎cu‎. ‎mtr‎, ‎upholstered ‎ with fabric or leatherette .UNDERSTRUCTRE ‎: ‎Understructure is made ‎up of ‎1‎.‎2‎±‎0‎.‎1 ‎cm‎. ‎thick ‎hot pressed plywood ‎( moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY‎: ‎It is ‎a welded assembly ‎made in Stainless steel ‎(‎grade SS ‎202‎) ‎tube ‎& ‎plate‎ with plastic endcap. (W) 86.0* (D) 90.5(H) 85.5 cm seat (H) 45.0 cm

CABIN

SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE 47.5 cm. (W) x 69.5 cm (H) SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO mechanism: The mechanism should be designed with the following features: • 360° revolving type. • Upright-position locking • Tilt tension adjustment • Seat/back tilting ratio of 1:3. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLYThe bellow should be 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY:The pedestal should be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Nylon. Overall Dimensions of Chair Seat Height - min 42.5 to max 54.5cm. Height - min97.0 to max 109.0cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood. OCP-QLTA-P14.18 and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed with contoured lumbar support for extra comfort BACK SIZE: 41.0cm. (W) X 46.0cm. (H) ]SEAT SIZE: 43.0cm. (W) X 41.0cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR Polyurethane foam should be moulded with density = 45 ±2 kgs. /m3 and Hardness load 16 ± 2 kgf for 25% compression ARMRESTS : The armrest should be .made of black integral skin polyurethane with 50-70 Shore A hardness and reinforced with MS insert. The P.U. armrest should be fixed to black powder coated DFT 40-60 microns ) armrest bracket made of 0.5 ± 0.05cm. thk. HR steel. PERMANENT CONTACT mechanism: The permanent contact mechanism should be designed with the following features:- 360° revolving type 14° ±2° maximum back-tilt only. Upright position locking Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm TELESCOPIC BELLOW ASSEMBLY: The bellow should be 3 piece telescopic type and injection moulded in black Polypropylene PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet (should be :DD 10791 HR) , powder coated ( DFT40-60 microns ) and fitted with an injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 55.0 ±0.5cm. pitch-center dia. (65.0 ±1.0cm with castors) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon Overall Dimensions of Chair Seat Height - min 42.0 to max 54.0cm. Height - min80.0 to max 92.0cm. Width & Depth of Chair as measured from pedestal - Width-65.0 cm and Depth-65.0 cm.

Finesse Table - 5026 size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. Finesse ERU -3616 LHS size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.

Storage Cabinate - Overall Dimensions of VSDU - 12 shall be 1200mm(W)x450mm(D)x1192.5mm(H) . The top shall be wooden top PLB(25 mm add in unit height ) . The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU - 12 shall have 4 no. of adjustable half shelves . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU 12 - A4 size box file can be stored vertically on two shelves and clear space above third shelf is 295 mm .