National Bank For Agriculture And Rural Development Tender

Dismantling doors including chowkhats, architrave, holdfasts etc. of area of 3 sqm. and below complete and stacking within 50 meters lead.

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground outside municipal limits With cement mortar 1:4 (1 cement : 4 fine sand)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in superstructure up to floor v level including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand

Dismantling tile work in floors and walls, wherever required, laid in cement mortar including disposal of malwa beyond municipal limits. Providing and laying vitrified floor tiles in 600x600 mm with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. and skirting till 150 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size in dado upto ceiling level over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. 19.3.2 Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 20mm nominal outer dia pipes with all necessary accessories required for complete fitting

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. 19.3.2 Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 50mm nominal outer dia pipes with all necessary accessories required for complete fitting

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. 19.3.2 Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 75mm nominal outer dia pipes with all necessary accessories required for complete fitting

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete,including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid

Supplying and fixing best approved best quality SS Health Facet with Stop cork of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications (make parryware/hindware/equivalent)

Providing and fixing CPVC inlet connection for flush pipe connecting with W.C. pan

Providing and fixing SS gully trap of approved size and make

Providing and fixing CP Brass wall mixer of quality & make

Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer including providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete 32 mm dia flexible pipe, providing and fixing PTMT Waste Coupling for wash basin and sink, and CP nipples, of approved quality, make and colour

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gm

Providing and fixing CP brass angle valve for wash basin and geyser points of approved quality conforming to IS: 8931 15 mm nominal bore

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet 150mm diameter

Providing and fixing PTMT soap dish holder having length of 138 mm, breadth 102mm, height of 75mm with concealed fittings arrangements, weighing not less than 106gm

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms.

Door Frames for bathroom: Dismantling of old door frames, providing and fixing wood (Sal wood) work in frames (5 inch single rebated) of doors, wrought framed and fixed in position with hold fast lugs or with dash fasteners. The frame shall be fixed with 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block (Approximate length 19 ft each frame) Doors for bathroom: Supplying and fixing of 30mm thick factory made flush door shutters (Century/Greenply or equivalent) with 1.00mm thick decorative laminate of approved make (Century/Greenply or equivalent), texture and shade on both side of shutters pasted with adhesive (Pidilite or equivalent). The shutters shall be fixed with atleast three SS hinges of approved make; provided with margins at all edges; one mortice door lock handle (Godrej or equivalent); two 200mm tower bolts (Godrej or equivalent); 1 door stopper and 75mm door buffer. (Approximate door size 20 sq ft/door). Fixing of frames and doors shall include complete repairs (floor & wall) to the damaged incurred during the dismantling of old door frames.

Door Frames for entrance doors: Dismantling of old door frames, providing and fixing wood (Sal wood) work in frames (5 inch single rebated) of doors, wrought framed and fixed in position with hold fast lugs or with dash fasteners. The frame shall be fixed with 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block (Approximate length 19 ft each frame)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. Laying of veneer as per drawing. Make: Green, archid, duro or equilvent) 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)

Providing and fixing wooden moulded corner beading / joint filler of triangular / rectangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. Complete job in 2nd class teak wood

Melamine polishing on wood work (one or more coat) all job Complete

Providing and fixing of fastner 150 mm long including fixing to frame with 8 mm diameter bolts.

Providing and fixing Stainless Steel tower bolts ISI marked (304 grade) with necessary screws etc. complete. ( Make: Godrej, Harrison or equivalent)

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing Mortise Door Lock Handle Set 1ck(EM01, ss finish)- 6 lever lock, 3 keys, double throw-5" handle, Left/Right Handed Door Operation- Mortise Lock with Latch for Home, Main Door, Internal Doors (Model Number- 7750) of approved quality with necessary screws etc. Complete (Make: Godrej, Harrison or equivalent)

Providing and fixing stainless steel hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges (heavy weight) with Stainless Steel screws etc. complete.

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete :