Jammu And Kashmir State Sports Council Tender

Providing and laying in Position Cement Concrete of specified grade excl. the cost of centering, shuttering all works upto plinth level in 1:2:4 with (1 cement : 2 course sand : 4 graded stone agg. 20mm nominal size crushed aggregate)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix,I ncluyding pumping of concrete to site laying but excluding the cost of centering, shuttering,finishing and reinforcement, including admixtures in recommended proportions as per IS:9103 to accelerate, retard setting of concrete ,improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable seperately all works plinth level excl. carriage up to site of work

Reinforcement for R. C. C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars .( All work at all levels complete.)

Structural steel work in welded in built up sections trusses and framed work, including cutting, hoisting, fixing in position and applying of priming coat of approved steel primer complete in all respects..(All work at all levels complete.)

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing form work including Centring ,shuttering , strutting, propping etc. using ply wood sheeting with water proofing ply board and removal of the same for ( All works at all levels complete.).- a) Foundations, footings, bases of columns etc. for mass concrete.

b) Columns, pillars, piers, abutments, posts and struts etc

b) Beams

Filling available excavated earth (excluding rock) in trenches plinth, sides of foundation etc. layers not exceeding 20Cm in depth consolidationg each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Excavating, supplying and filling of local earth (including royalty)by mechanical transport up to a lead of 5 km also including ramming and watering of the earth inlayers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

Brick masonry with FPS bricks of class designation 75 in super structure up to floor V level in cement mortar 1:6 (1cement: 6 coarse sand). complete in all respects

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made (As per Sample)

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (As per Sample)

Providing and fixing 20 mm thick T&G planks made of imported wood (New zealand pine or equivalent) on wood work in false ceiling, wall/wall partitions sawn and put up in position ( budloo wood Ceiling Joists of 50 mm x 65 mm in sections placed @ 600 mm C/C both ways or as required at site). including cost of necessary adhesive & cost of nails etc. all complete upto floor 5 level as per the directions of Engineer-in-charge (including cost of all material, leads, lifts and carriages etc upto site of work complete).(For panelling /Ceilings/Soffits etc.)

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position Budloo / Fir wood

Providing and fixing planed eves boarding of Ist class kail wood (250 x 32 mm ) N/S with necessary grooves and chamfer as per detailed drawing / as per the directions of Engineer In charge

Providing and fixing precoated galvanized iron high profile sheets Crill make or equivalent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete uptoany pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (0.50 mm thickness )

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete (Ridges /Valleys etc. plain (500 - 600mm)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(600 x 600 mmm)

P/f glass mosaic titles at finsihed plain wall surface of size 20mm x20mm x4mm in all colour, design, fixing in customize design as per direction of Engineer-in-charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 Kg per Sqm and grouting of the same. the rate is inclusive of all operation material and required pattern approved by Engineer incharge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing Aluminium Composite Powder coated sheet cladding as per drawing, using Shree Narmada Aluminium mill finish rectangular Vertical tube size - 50x150x2mm having wt. 2.13kg/m & horizontal square tube size 50x50x2mm having weight 1.043 kg/m including 4mm thick aluminium composite panel sheet with 0.5mm aluminium foil thickness, backer rod, & the periphery of cladding panel shall be sealed with weather Silicone of Dow Corning/Walker make, necessary screws & hardware etc., including 5 mm thick toughened glass complete in all respect, as per the directions of engineer in charge

Making plinth protection 50mm thick of cement conc. 1:3:6 (1 cement: 3 coarse sand : 6 graded stone agg 20mm nominal size) over 75mm bed of dry stone agg. 40mm nominal size well rammed and consolidation and grouted with fine sand incl. finishing the top smooth.

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, curing, fixing and finishing complete in cement mortar 1:3 (1 cement : 3 fine sand) etc. complete excluding plastering of the jambs, sills and soffits.

Providing and fixing in wall lining of specified medium density board, pre-laminated one side decorative lamination other side balancing lamination Grade I, exterior grade, with necessary fixing arrangement and screws etc. complete. Flat pressed 3 layer particle board or graded wood particle board grade-I type-II, IS: 12823 marked including primer coat on unexposed surfaces (18 mm thick

Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing.(Rough chisel dressed)

Providing and fixing ornamental wooden columns/ posts of 200 mm x200 mm (average size) as per approved design of consultant of (ist class Kail wood) fixed with base/top plates/frames with necessary 16 mm dia holding down bolts complete in all respects.

Carriages of materials from source to site of work by mechanical transport/head load if any and for any unforseen items complete as per the site requirements a) Sand /Aggregate av. lead 10kms

Bricks av. lead 10kms

Supply fixing testing and commissioning of underwater light Niche in UV treated ABS 14.5 Watt 12 Volt with 3 Mtr cable and conduit to be laid in poolwall make Aquafine, Hayward Astral or equivalent

Providing and laying in situ seven course water proofing treatment with APP (Atactic poly- propylene) modified Polymeric membrane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/ sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS: 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane of specified thickness, weight and centre core, HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement:3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement: 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately.) Modified Polymeric membrane 2.0 mm thick of 3.0 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micro

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge in all respects a) 50mm nominal outer dia pipes

b) 62.50mm nominal outer dia pipes

c) 75mm nominal outer dia pipes

d) 100mm nominal outer dia pipes

Providing of structural and Geo Tech investigation Consutancy services. The scope of work includes soil investigation/ Geotechnical investigation. ETS Maping complete if required at Site, prepration of structural drawings, and vetting of structural drawing by any third party. Any other service not specially mentioned here but required for the proper and successful completion of the project shall be proposed and designed at no extra cost Structure should be designed on latest version of STAAD-PRO taking into account of latest Earthquake IS Code available as per the approved drawings and site conditions.