Jammu And Kashmir State Sports Council Tender

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work

P/F of 100 liter capacity outdoor ,HDPE Plastic dustbin including carriage complete job. Neel Kamal or equivalent make

Arm wheel: Providing and fixing Arm wheel in a pair with below specifications: Dimensions(LxWxH): 850 x 800 x 1800 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pilar with wheel frame of NB 50mm. All pipes must be (G.I.) ‘C’ Class Pipes. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label & sports council logo shall be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

ELLIPTICAL EXERCISER Providing and fixing of Elliptical exerciser with below specifications: Dimensions (LxWxH): 1200 x 550 x 1600 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 80mm (G.I.) ‘C’ Class Pipe. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label & sports council logo shall be fixed on equipment for ease of use. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

DOUBLE CROSS WALKER Providing and fixing of Double cross walker with below specifications: Dimensions (LxWxH): 1600 x 600 x 1600 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). Foot support frame of 96 x 46 x 3mm MS rectangular pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless-steel label & sports council logo shall be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

TRIPLE TWISTER Providing and fixing of Triple twister with below dimensions: Dimensions (LxWxH): 1300 x 1300 x 1650 mm Shall be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Handle Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. Handle frame spokes of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). Foothold plate of made of MS Sheet Metal of 3mm thickness. All Pipes shall be powder coated with 80–120-micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness & Base plate of 12 mm thickness. Once the concrete is set, the equipment shall be fixed on to it. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless-steel label & sports council logo shall be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

DOUBLE PULL CHAIR Providing and fixing of Pull chair in a pair with below specifications: Dimensions (LxWxH): 2400 x 800 x 2000 mm Shall be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Seat main frame of NB 50mm (G.I.) ‘C’ Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all the welding points prior to finishing. Handle bars to be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated to be used used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is to be fixed on to it and nuts and bolts to be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label & sports council logo to be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

SIT UP STATION Providing and fixing of Double sit-up station with below specifications: Dimensions (LxWxH): 1600 x 1150 x 650mm shall be Fabricated with main frame of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 25mm (G.I.) ‘C’ Class Pipe. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) Perforated MS Sheet for Back Support. The back support Fixed on its top is to be made of perforated MS sheet of 2mm thickness. All pipes shall be powder coated using Akzo Nobel or equivalent Paint of 80- 120 micron thick. All joints of pipes shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is to be applied at all welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. The equipment is to be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is to be fixed on to it. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless-steel label & sports council logo shall be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

AIR SWING Air swing in a pair with below specifications: Dimensions (LxWxH): 1150 x 900 x 1250 mm To be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be to be fitted with inbuilt limiters to prevent unwanted movements. The equipment is to be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is to be fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label & sports council logo fixed on equipment for ease of use Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

LEG PRESS Providing and fixing leg press in a pair with below specifications: Dimensions (LxWxH): 2000 x 600 x 1800 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label & sports council logo fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Knee Hip Raise (Chin Ups / Dips / Push Ups): CHIN UPS: Instrumental in building upper body muscles especially that of the back and shoulder. Wide and narrow grips provide for various permulations of popular exercise. DIPS: Soft handgrips for dipping using your own body weight. A very strong and robust exercise fortriceps, shoulders and back muscles. PUSH UPS: Appropriately heighted rolled bars that relieve unneces-sary stress from wrist and forearms. Allows user to dip lower for a more complete arm, chest, shoulder and back workout. Dimensions (LxWxH): 1400 x 1100 x 2100mm. Fabricated with base frame of NB 50mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. Leg support of NB 32mm (G.I.) ‘C’ Class Pipe and other support of NB 25mm (G.I.) 'C' Class Pipes (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters), All pipes shall be powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs, Zinc primer paint is applied at all welding points prior to finishing,The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness,Once the concrete is set, the equipment is fixed on to it.High tensile steel with galvanized nut bolts shall be used for assembly, Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment, Self-Explanatory stainless steel label fixed on equipment for ease of use. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Horse rider station Horse rider station with below specifications: Dimensions (LxWxH): 1000 x 600 x 1100 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe and other pipes of NB 32mm & NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 32mm (G.I.) ‘C’ Class Pipe. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Exercising bar Exercising bar in a pair with below specifications: Dimensions (LxWxH): 1800 x 550 x 1500 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing.Make approved by authority and maintenance of same upto 3 years cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. The equipment is fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label & sports council logo fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Rowing machine Rowing machine with below specifications: Dimensions (LxWxH): 1250 x 800 x 1150 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label & sports council logo fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Providing and fixing of Durable SBR TILE flooring Protects floor from damages by dumbbells and iron gym material Thickness:25 mm Dimensions: 490mm x 490mm SBR-25 SBR TILE of approved make and colour and as per directions of engineer in charge incl cost and carriage incl necessary jointing by cement concrete or adhesives including forming of at least 0.15m x 0.15m or above (width x thickness) block on all sides of tiles as per dierctions of engr incharge including all finishing in all the respects complete job . Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.