Jammu And Kashmir State Sports Council Tender

Hot water flow rate : 40 USGPM Head : 12 M Maximum Permissible Speed : 1440 RPM Motor Rating : 1.5 HP End suction, single stage volute pumps as described above including one standby.

Providing and Fixing of Ball, Globe and Non return valves, 'Y' Strainers. A) Butter Fly Valves 125mm dia

B) 100mm Dia

C) 80mm dia

D) 65mm dia

E) 50mm dia

Y Stainers 50mm dia

40mm dia

25mm dia

Non Return Valve 50mm dia

25mm dia

Ball Valves 50mm dia

40mm dia

32mm dia

25mm dia

15mm dia

Providing, fixing, testing & commissioning of Pressure operated Pump with 100 ltrs. Expansion Tank complete with fittings, valves, mountings and motor base.

Supply, Installation, Testing and Commissioning of double skin sheet metal sectionalised construction Treated Fresh Air Units, with double skin panels with 46mm thick injected PUF of density not less than 40Kg/CuM. The air handling units shall be complete with pre-filter , UVGI, section with 6 row deep chilled water cooling coil of copper tube & aluminium fin construction suitable for 2-pipe system, fan section complete with floor standing forward curved DIDW centrifugal fan, belt drive package, IE-02 squirrel cage induction motor, insulated SS drain pan, copper header with "Copper to MS" adopter, vibration isolation pads etc. all complete as per the specifications.TFAs shall be selected for a maximum face velocity of 500 FPM (2.5 MPS) and as per schedule of air handling units drawn under Appendix VIII. Fan outlet velocity shall not exceed 2000 FPM (10.1 MPS). The unit/s shall be be provided with factory fabricated plenum on filter side (mixing box), with access doors /panels for fresh air duct termination. AHUs shall be of following design parameters:: 20000 CFM (F/M)

Supply, installation, testing and commissioning of Hydronic Floor Heating by way of laying of Polythene, 25mm thick XPL sheets with density 32 Kg/Cum , P/L of (16/20) pex pipes held together with Iron Bars joint by electric ties, the Spain between the pipes will be 4 inch and iron bars 8 inch respectively.

Supply, Installation, Testing & Commissioning of high efficiency tube axial type Axial Flow Fans complete with MS casing, impeller high efficiency motor with class "H" insulation for smoke extraction as shown in the drawings. Motor shall be suitable for operation on 415±10% volts, 50Hz, 3 phase AC power supply and capable to withstand 2500 C temperature for a minimum duration of 2 hours. Provide sound attenuators where asked for below and as per design drawings, the same shall be inclusive in the quoted price. Axial flow fans shall be provided with inlet and outlet cones fabricated at site using GS sheet and necessary vibration isolation arrangement including spring type vibration isolators and rubber gromet etc. as required. : 5000 CFM (C/M)

Supply, installation, testing & commissioning of M.S. Class ‘C’ Heavy duty pipes and fittings like tees, elbows, bends, junctions, unions, flanges etc. clamps structural supports as req./ directed at site incl. painting the pipes with desired shade of enamel paint over a coat of primer. The Pipes shall be measured as per actual. A) 15 mm dia

20mm dia

25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

80mm dia

100mm dia

125mm dia

Supply, Installation, Testing Elastometric closed cell Insulation of 13 mm thick over the piping of following dia.The Pipes shall be measured as per actual. A) 15mm dia (13mm)

20mm dia (13mm)

25mm dia (13mm)

32mm dia (13mm)

40mm dia (13mm)

50mm dia (19mm)

65mm dia (19mm)

80mm dia (19mm)

100mm dia (19mm)

125mm dia (19mm)

Supply, Installation, Testing of Al. Cladding Insulation of pipes and two layers of Polythene and Chickenmesh over the piping of following dia. The Pipes shall be measured as per actual. A) 32mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

125 mm dia

Supply, Installation, Testing Puff Insulation of 50mm thick over the piping of following dia.The Pipes shall be measured as per actual. A) 32mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

125 mm dia

Supply, installation, testing and commissioning of Brass Manifold of 32mm with 10 holes each fitted with FTC, MTC, air vent, suitable ball valves, nipples, and other accessories per specifications.

Supply, Installation, Testing of Room Thermostate. (manual)

Supply, Installation, Testing of star bound fibre cloth and polished with adhesive. Insulation over the piping of following dia. The Pipes shall be measured as per actual. A) 15mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

125 mm dia

Supply, installation, testing & commissioning of Pex Pipe and fittings like tees, elbows, junctions, etc. clamps structural supports as req./ directed at site incl. primer. The Pipes shall be measured as per actual. A) 16/20 mm dia

Providing and fixing rigid PVC piping complete with fittings, supports as per specifications and duly insulated with 10 mm thick Elastometric closed cell Insulation. A) 20mm dia (10mm thick)

25mm dia (10mm thick)

32mm dia (10mm thick)

Supply, installation, testing & commissioning of Galvanized Sheet Metal Ducting complete with supports, hangers, etc. as per specification & drawings and complete with Nertrolic Foam insulation 10 mm thick. A) 0.63mm (24 Guage)

0.80mm (22 Guage)

1.00mm (20 Guage)

Supply, installation, testing and commissioning supply and return air grilles of different sizes as per specifications including fixing frame of G.I. in false ceiling complete as required. A) Supply/Greturn grill with dampers

Jet Air Diffuser 400mm dia

Diffuser 600x600mm

Supply, Installation, Testing of 3-Way value with Actuator, Thermostate, Transformer. A) 50mm dia

40mm dia

Supply, Installation, Testing of Solinoide Value. A) 50mm dia

40mm dia

Cleaning and checking for any leakage for the existing round duct with some rectification like adding some more grills and collar tothe same.

Making good of already existing axial flow fans by checking their motors and fan blades etc

Electrical Control Panel (Plant Room) Supplying, assembling, erecting, connecting, testing and commissioning of dust, damp free floor standing factory built sheet steel enclosed non-drawout modular type Panel fabricated out of suitable sized angle iron and flats, with clean agent gas cylinder automatic system, base channel and covered with 2.0mm thick PCRC sheet, duly painted complete with earth bus, aluminum bus bar, numbering & sign writing, interconnection & including the cost of connection through bus bar / copper conductor flexible connection with all accessories, rotary handles,phase barriers etc. complete as shown in drawing & as per specifications and mounted with the followings etc. complete as required. (All the starters should have NO/ NC contacts for remote/ fire control facility etc. complete) Incoming: 2 No. 300 amps, (Ics=Icu) TPN MCCB with thermal magnetic overcurrent and short circuit release complete with Digital flush type class- I accuracy with power load manager, showing V, A, KVA, KWH etc. with 3 Nos. current transformers of 250/5A ratio, 10 VA Class 1.0 metering. 1 Set of RYB phase indicating & ON/OFF/TRIP LED lamps with 2Amps. SP MCB's backup. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral busbars rated at 415V, 50 Hz., 100 amps, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing:- 125 TPN MCCB with TM release - 3 nos. 25A 4P MCB 'C' - 1nos. 63A 4P MCCB 'C' - 2 nos. 40A 4P MCB 'C' - 3 nos. 300A 4P MCCB 'C' - 0 nos. Fully automatic DOL starter suitable for 7.5 KW motor including suitable TP MCB 'C', CT's, Ammeter, Push Buttons, LED Indications, Auto/ Manual/ OFF selector switch, SPPR, FRLS copper control wiring etc. Complete - 3 Set Fully automatic DOL starter suitable for 0.75 KW motor including suitable TP MCB 'C', CT's, Ammeter, Push Buttons, LED Indications, Auto/ Manual/ OFF selector switch, SPPR, FRLS copper control wiring etc. Complete - 2 Set Fully automatic DOL starter suitable for 1.1 KW motor including suitable TP MCB 'C', CT's, Ammeter, Push Buttons, LED Indications, Auto/ Manual/ OFF selector switch, SPPR, FRLS copper control wiring etc. Complete - 2 Sets Fully automatic DOL starter suitable for 2.2 KW motor including suitable TP MCB 'C', CT's, Ammeter, Push Buttons, LED Indications, Auto/ Manual/ OFF selector switch, SPPR, FRLS copper control wiring etc. Complete - 2 Set

Electrical Control Panel (AHU+Elec Boiler) Supplying, assembling, erecting, connecting, testing and commissioning of dust, damp free floor standing factory built sheet steel enclosed non-drawout modular type Panel fabricated out of suitable sized angle iron and flats, with clean agent gas cylinder automatic system, base channel and covered with 2.0mm thick PCRC sheet, duly painted complete with earth bus, aluminium bus bar, numbering & sign writing, interconnection & including the cost of connection through bus bar / copper conductor flexible connection with all accessories, rotary handles,phase barriers etc. complete as shown in drawing & as per specifications and mounted with the followings etc. complete as required. (All the starters should have NO/ NC contacts for remote/ fire control facility etc. complete) Incoming: 1 No. 150 amps, (Ics=Icu) TPN MCCB with thermal magnetic overcurrent and short circuit release complete with Digital flush type class- I accuracy with power load manager, showing V, A, KVA, KWH etc. with 3 Nos. current transformers of 250/5A ratio, 10 VA Class 1.0 metering. 1 Set of RYB phase indicating & ON/OFF/TRIP LED lamps with 2Amps. SP MCB's backup. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral busbars rated at 415V, 50 Hz., 100 amps, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing:- 16A SP MCB 'C' - 2 nos. 25A 4P MCB 'C' - 0 nos. 63A 4P MCCB 'C' - 2 nos. 40A 4P MCB 'C' - 0 nos. 100A 4P MCCB 'C' - 2 nos. Fully automatic DOL starter suitable for 2.0 KW motor including suitable TP MCB 'C', CT's, Ammeter, Push Buttons, LED Indications, Auto/ Manual/ OFF selector switch, SPPR, FRLS copper control wiring etc. Complete - 2 Set Fully automatic DOL starter suitable for 2.2 KW motor including suitable TP MCB 'C', CT's, Ammeter, Push Buttons, LED Indications, Auto/ Manual/ OFF selector switch, SPPR, FRLS copper control wiring etc. Complete - 2 Set

Electrical Control Panel (AHU+Ehuast) Supplying, assembling, erecting, connecting, testing and commissioning of dust, damp free floor standing factory built sheet steel enclosed non-drawout modular type Panel fabricated out of suitable sized angle iron and flats, with clean agent gas cylinder automatic system, base channel and covered with 2.0mm thick PCRC sheet, duly painted complete with earth bus, aluminium bus bar, numbering & sign writing, interconnection & including the cost of connection through bus bar / copper conductor flexible connection with all accessories, rotary handles,phase barriers etc. complete as shown in drawing & as per specifications and mounted with the followings etc. complete as required. (All the starters should have NO/ NC contacts for remote/ fire control facility etc. complete) Incoming:1 No. 150 amps, (Ics=Icu) TPN MCCB with thermal magnetic overcurrent and short circuit release complete with Digital flush type class- I accuracy with power load manager, showing V, A, KVA, KWH etc. with 3 Nos. current transformers of 250/5A ratio, 10 VA Class 1.0 metering.1 Set of RYB phase indicating & ON/OFF/TRIP LED lamps with 2Amps. SP MCB's backup. Bus Bars:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 415V, 50 Hz., 100 amps, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing:- 16A SP MCB 'C' - 2 nos. 25A 4P MCB 'C' - 0 nos. 63A 4P MCCB 'C' - 2 nos. 40A 4P MCB 'C' - 0 nos. 100A 4P MCCB 'C' - 2 nos. Fully automatic DOL starter suitable for 2.0 KW motor including suitable TP MCB 'C', CT's, Ammeter, Push Buttons, LED Indications, Auto/ Manual/ OFF selector switch, SPPR, FRLS copper control wiring etc. Complete - 2 Set Fully automatic DOL starter suitable for 2.2 KW motor including suitable TP MCB 'C', CT's, Ammeter, Push Buttons, LED Indications, Auto/ Manual/ OFF selector switch, SPPR, FRLS copper control wiring etc. Complete - 2 Set

Electrical cable Providing and fixing Flame Retardent Low Smoke, XLPE insulated, outer sheated armoured aluminium/Copper conductor cables from main panel boards to various equipments through walls/ceiling with appropriate clamps and fixing arrangements, cable termination etc. as per specifications and drawings. 31/2 Core - 400mm2 (AI)

4 Core - 35 mm2 (Al)

4 core - 16 mm2 (Al)

4 core - 10 mm2 (Cu)

4 core - 6 mm2 (Cu)

4 core - 4 mm2 (Cu)

4 core - 2.5 mm2 (Cu)

Cable Tray Fabricating and installing perforated GI cable trays including horizontal and vertical bends, reducers, tees cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including painting etc. as required. A) 100mm X 50mm X 1.6mm

150mm X 50mm X 1.6mm

Earthing Providing and fixing 25 mm x 5 mm G.I. strip on surface or in recess for earth connection etc. complete as required.

Providing and fixing 8 SWG dia GI wire on surgace or in recess for loop earthing alongwith the existing surface/ recessed conduit/ submain wiring/ cable as required.